Re: [PATCH v5 0/2] usb: dwc3: fixes for two connectors sharing one HS bus

[Krishna Kurapati]

On 10/31/2026 8:31 PM, Qianhui Xu wrote:
> *** AI-assistance disclosure ***
> This cover letter and the accompanying patches were prepared with the help
> of an LLM coding assistant; the author reviewed, tested and takes full
> responsibility for the content. All measurements cited below come from real
> hardware runs and are reproducible with the commands referenced in our
> public reports.
>
> Greetings,
>
> This is v5.  It is a fixup series that applies *on top of* v4 [1] -- it
> does not replace v4 1/3..3/3, it fixes them in place:

If v5 is being sent, it must not to be applied on top of v4. It must 
include (v4 + any additional changes/improvements).

Regards,
Krishna,

>    - 1/2 tightens the binding of v4 1/3 (snps,dwc3-common.yaml),
>    - 2/2 fixes the driver of v4 3/3 (usb: dwc3: support two connectors
>      sharing one HS data bus) and also corrects
>      usb_role_switch_at_endpoint() introduced by v4 2/3.
>
> Base: v4 3/3 (fd69bd54e328, "usb: dwc3: support two connectors sharing
> one HS data bus").  Please apply v4 1/3..3/3 from lore [1] before this
> series; the `base-commit:` trailer in this posting is informational only,
> since it names a commit that is not in any public tree yet.
>
> Hardware: Lenovo Legion Y700 (4th gen) tablet, SM8750.  Both High Speed
> connectors share one DWC3 controller; a port-select GPIO picks which
> connector owns the bus, and each connector has its own typec port with its
> own role switch, described per graph endpoint.
>
> Changes since v4 (all points are replies to the automated review by
> Sashiko [2][3][4]; no human maintainer replied in the v4 thread yet):
>
> Binding (Sashiko on v4 1/3, three Medium findings [2]):
>
>    * "hs-port patternProperties does not match what the driver expects /
>      escapes unevaluatedProperties".  Fixed: the endpoint name pattern is
>      now the same one graph.yaml uses, so an unnumbered endpoint or
>      endpoint@2+ is validated too instead of silently escaping the
>      unevaluatedProperties: false rule (v5 1/2).
>
>    * "usb-role-switch should not be required only indirectly".  Fixed: the
>      controller node must now carry "usb-role-switch" whenever
>      port-select-gpios is present.  This is a driver-fact fix, not just
>      schema cosmetics: without that property dwc3_get_dr_mode() forces
>      dr_mode back to peripheral and dwc3_drd_init() never runs, so a DT
>      that passed the old schema did not describe a DT the driver could act
>      on (v5 1/2).
>
>    * "mux-state complementarity is not expressed".  Fixed: the two
>      independent `if: const: 0` blocks only rejected two zeroes; two
>      endpoints both claiming mux-state = <1> passed validation.  The pair
>      is now a single oneOf so exactly one assignment is accepted (v5 1/2).
>
>    * On the standing question whether this should use the standard
>      mux-controls/mux-states properties instead of per-endpoint role
>      switches: kept the graph-endpoint shape for now.  Reason: the
>      arbitration is "earliest request wins" between two *typec connectors*
>      that must each be a usb role switch consumer, and the endpoint is the
>      fwnode the connector is attached to; a mux-control consumer does not
>      give us that per-connector identity.  drivers/usb/ has no
>      mux_control consumer today to follow as precedent.  Happy to reshape
>      if the DT maintainers prefer the standard property.
>
> usb: roles (Sashiko on v4 2/3, one High finding [3]):
>
>    * "-EPROBE_DEFER is swallowed by !IS_ERR_OR_NULL(sw)".  Fixed: pass the
>      error up, as suggested (v5 2/2, last hunk).  This was also the root
>      cause we hit on real hardware: the UCSI glue kept a NULL switch and
>      the connectors never bound.
>
> usb: dwc3 (Sashiko on v4 3/3, five High + three Medium findings [4]):
>
>    * "dwc3_set_mode() under dwc->lock self-deadlocks".  Fixed: request
>      decision and issue are now paired by mux->lock; dwc->lock is only held
>      while updating the individual fields (v5 2/2).
>
>    * "glue layer is never notified".  Fixed: dwc3_pre_set_role() is called
>      with the effective role, outside spinlocks, before dwc3_set_mode(),
>      mirroring the single-connector path (v5 2/2).
>
>    * "same-role request that moves the data path to the other connector".
>      Fixed: dwc3_set_prtcap() only clears SUSPHY when PRTCAP changes, so
>      that case now clears it explicitly (v5 2/2).
>
>    * "registration earlier than the initial mode request races with a
>      connector driver".  Fixed: register and request the initial mode under
>      mux->lock, tear down in reverse order on failure (v5 2/2).
>
>    * "fwnode references leak on error paths".  Fixed: dwc->role_mux is
>      published before the error paths that used to leak the endpoint
>      fwnodes, so dwc3_role_mux_exit() can actually unwind (v5 2/2).
>
>    * "sticky mux->error is reported to the next caller after it already
>      committed its own request".  Fixed: the sticky value is dropped; a
>      failed data-path switch is logged and counted per connector (v5 2/2).
>
>    * (found during on-device testing, same area) dwc3_mux_role_get()
>      returned USB_ROLE_NONE for a connector that did not own the data path,
>      hiding its pending request; the connector driver then never sent the
>      set_role(NONE) that would clear it, and the stale request kept winning
>      arbitration after unplug.  get() now reports the requested role
>      (v5 2/2).
>
> Test evidence (all on the SM8750 tablet, kernel built from this series):
>
>    - `git am --3way` of the whole series on top of v4 3/3 succeeds;
>      checkpatch --strict reports 0 errors / 0 warnings / 0 checks for both
>      patches.
>    - `dt-doc-validate` on snps,dwc3-common.yaml: clean.
>    - `make W=1 drivers/usb/dwc3/ drivers/usb/roles/` (arm64): 0 warnings.
>    - On device: after the -EPROBE_DEFER fix, /sys/class/typec shows port0,
>      port1 and a bound partner; with function_graph tracing, 12 consecutive
>      plug/unplug cycles each went usb_role_switch_set_role ->
>      dwc3_mux_role_set [dwc3] -> glue notifier -> dwc3_set_mode with zero
>      WARNING/BUG/lockdep splats, USB data and charging both stable
>      throughout.
>    - The binding topology (two HS connectors on port@0 and port@2 of the
>      controller's port node, one endpoint each, mux-state on the endpoint)
>      matches what the board DTS uses; port@1 is occupied by the SuperSpeed
>      path to the QMP PHY, which is why the two HS connectors are not
>      siblings under one port.
>
> Known limitation, stated up front: the role *arbitration* detail (which
> connector wins a simultaneous request) is verified only by code reading and
> the stale-request test above; a dedicated per-port role-value trace is
> instrumented but its data set is not yet complete.  Everything else listed
> above has been exercised on hardware.
>
> Thanks,
> Qianhui Xu
>
> [1] v4: https://lore.kernel.org/linux-usb/20261026123211.243224-1-xiaqinghuan@xxxxxxxxxxxxxxxx/
> [2] Sashiko on v4 1/3: <sashiko-outbox-185247@xxxxxxxxxx>
> [3] Sashiko on v4 2/3: <sashiko-outbox-185254@xxxxxxxxxx>
> [4] Sashiko on v4 3/3: <sashiko-outbox-185299@xxxxxxxxxx>
>
> Qianhui Xu (2):
>    dt-bindings: usb: snps,dwc3: tighten the two-connector shared HS bus
>    usb: dwc3: fix the two-connector shared HS bus role handling
>
>   .../bindings/usb/snps,dwc3-common.yaml        | 105 +++++++++---------
>   drivers/usb/dwc3/core.c                       |  36 ++++--
>   drivers/usb/dwc3/core.h                       |   4 +-
>   drivers/usb/dwc3/drd.c                        |  65 ++++++++---
>   drivers/usb/roles/class.c                     |   7 +-
>   5 files changed, 140 insertions(+), 77 deletions(-)
>
>
> base-commit: fd69bd54e328c407b1853378b25d15803d3453fa