[PATCH] arm64: dts: ti: Add LincolnTech OLDI LCD-185 Overlay for AM67A-BeagleY-AI
From: Swamil Jain
Date: Wed Nov 04 2026 - 10:33:00 EST
The panel is Lincoln Technology Solutions LCD185-101CT[0]. It is a
Dual-Link LVDS panel and supports WUXGA resolution (1920x1200).
Furthermore, it has an i2c based touch controller: Goodix-GT928.
Add DT overlay for the OLDI panel to connect with BeagleY-AI platform.
[0]: https://lincolntechsolutions.com/wp-content/uploads/2024/09/LCD185-101CTL1ARNTT_DS_R1.3.pdf
Signed-off-by: Swamil Jain <s-jain1@xxxxxx>
---
This overlay adds support for Lincolntech LCD-185 for BeagleY-AI.
The patch depends on "[PATCH v5 00/15] drm/tidss: Add BeagleY-AI display
support (and some more)"[1] series.
[1]: https://lore.kernel.org/all/20261103-beagley-ai-display-v5-0-f1c8d0e52bb4@xxxxxxxxxxxxxxxx/";
---
arch/arm64/boot/dts/ti/Makefile | 4 +
...-am67a-beagley-ai-lincolntech-lcd185-panel.dtso | 199 +++++++++++++++++++++
2 files changed, 203 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index da654153a35b..f7c0b514b330 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -207,6 +207,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6754-phyboard-rigel.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am67a-beagley-ai.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am67a-beagley-ai-csi0-imx219.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am67a-beagley-ai-csi1-imx219.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-am67a-beagley-ai-lincolntech-lcd185-panel.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm-csi2-quad-rpi-cam-imx219.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm-csi2-quad-tevi-ov5640.dtbo
@@ -370,6 +371,8 @@ k3-am67a-beagley-ai-csi0-imx219-dtbs := k3-am67a-beagley-ai.dtb \
k3-am67a-beagley-ai-csi0-imx219.dtbo
k3-am67a-beagley-ai-csi1-imx219-dtbs := k3-am67a-beagley-ai.dtb \
k3-am67a-beagley-ai-csi1-imx219.dtbo
+k3-am67a-beagley-ai-lincolntech-lcd185-panel-dtbs := k3-am67a-beagley-ai.dtb \
+ k3-am67a-beagley-ai-lincolntech-lcd185-panel.dtbo
k3-am68-sk-base-board-csi2-dual-imx219-dtbs := k3-am68-sk-base-board.dtb \
k3-j721e-sk-csi2-dual-imx219.dtbo
k3-am68-sk-base-board-pcie1-ep-dtbs := k3-am68-sk-base-board.dtb \
@@ -490,6 +493,7 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
k3-am642-tqma64xxl-mbax4xxl-wlan.dtb \
k3-am67a-beagley-ai-csi0-imx219.dtb \
k3-am67a-beagley-ai-csi1-imx219.dtb \
+ k3-am67a-beagley-ai-lincolntech-lcd185-panel.dtb \
k3-am68-phyboard-izar-lvds-ph128800t006.dtb \
k3-am68-phyboard-izar-peb-av-15.dtb \
k3-am68-phyboard-izar-pwm-fan.dtb \
diff --git a/arch/arm64/boot/dts/ti/k3-am67a-beagley-ai-lincolntech-lcd185-panel.dtso b/arch/arm64/boot/dts/ti/k3-am67a-beagley-ai-lincolntech-lcd185-panel.dtso
new file mode 100644
index 000000000000..8004c058bfb1
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am67a-beagley-ai-lincolntech-lcd185-panel.dtso
@@ -0,0 +1,199 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/**
+ * Lincoln tech Solutions OLDI panel (LCD185-101CT) and touch DT overlay for AM67A-BeagleY-AI
+ *
+ * This overlay adds support for the Lincoln tech LCD185-101CT OLDI panel interfaced with
+ * the DSS0 display subsystem on BeagleY-AI. The panel includes capacitive touchscreen support.
+ *
+ * Copyright (C) 2026 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "k3-pinctrl.h"
+
+&{/} {
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&backlight_pins_default &backlight_en_pins_default>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ enable-gpios = <&mcu_gpio0 11 GPIO_ACTIVE_HIGH>;
+ pwms = <&ecap0 0 20000 0>;
+ };
+
+ lcd {
+ compatible = "lincolntech,lcd185-101ct";
+ backlight = <&backlight>;
+ /*
+ * Note that the OLDI TX 0 transmits the odd set of pixels
+ * while the OLDI TX 1 transmits the even set. This is a
+ * fixed configuration in the IP integration and is not
+ * changeable. The properties, "dual-lvds-odd-pixels" and
+ * "dual-lvds-even-pixels" have been used to merely
+ * identify if a Dual Link configuration is required.
+ * Swapping them will cause an error in the dss oldi driver.
+ */
+ power-supply = <&vsys_5v0>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dual-lvds-odd-pixels;
+ lcd_in0: endpoint {
+ remote-endpoint = <&dss0_oldi0_out>;
+ };
+ };
+ port@1 {
+ reg = <1>;
+ dual-lvds-even-pixels;
+ lcd_in1: endpoint {
+ remote-endpoint = <&dss0_oldi1_out>;
+ };
+ };
+ };
+ };
+};
+
+&main_pmx0 {
+ backlight_pins_default: backlight-default-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x01f0, PIN_OUTPUT, 8) /* (A23) ECAP0_IN_APWM_OUT BL_PWM */
+ >;
+ };
+
+ touchscreen_int_pins_default: touchscreen-int-default-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x0038, PIN_INPUT, 7) /* (J22) GPIO0_14 TP_INT */
+ >;
+ };
+};
+
+&mcu_pmx0 {
+ backlight_en_pins_default: backlight-en-default-pins {
+ pinctrl-single,pins = <
+ J722S_MCU_IOPAD(0x002c, PIN_OUTPUT, 7) /* (C4) MCU_GPIO0_11 BL_EN */
+ >;
+ };
+
+ touchscreen_rst_pins_default: touchscreen-rst-default-pins {
+ pinctrl-single,pins = <
+ J722S_MCU_IOPAD(0x0030, PIN_OUTPUT, 7) /* (C3) MCU_GPIO0_12 MST_RST */
+ >;
+ };
+};
+
+&dss0 {
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* VP1: Output to OLDI */
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dss0_dpi0_out0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&dss0_oldi0_in>;
+ };
+
+ dss0_dpi0_out1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&dss0_oldi1_in>;
+ };
+ };
+ };
+};
+
+&dss0_oldi0 {
+ status = "okay";
+ ti,companion-oldi = <&dss0_oldi1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ dss0_oldi0_in: endpoint {
+ remote-endpoint = <&dss0_dpi0_out0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ dss0_oldi0_out: endpoint {
+ remote-endpoint = <&lcd_in0>;
+ };
+ };
+ };
+};
+
+&dss0_oldi1 {
+ status = "okay";
+ ti,secondary-oldi;
+ ti,companion-oldi = <&dss0_oldi0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ dss0_oldi1_in: endpoint {
+ remote-endpoint = <&dss0_dpi0_out1>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ dss0_oldi1_out: endpoint {
+ remote-endpoint = <&lcd_in1>;
+ };
+ };
+ };
+};
+
+&main_i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c1_pins_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ eeprom@57 {
+ compatible = "atmel,24c256";
+ reg = <0x57>;
+ };
+
+ touchscreen@5d {
+ compatible = "goodix,gt928";
+ reg = <0x5d>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchscreen_int_pins_default &touchscreen_rst_pins_default>;
+ interrupt-parent = <&main_gpio0>;
+ interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
+ irq-gpios = <&main_gpio0 14 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&mcu_gpio0 12 GPIO_ACTIVE_HIGH>;
+ touchscreen-size-x = <1920>;
+ touchscreen-size-y = <1200>;
+ };
+};
+
+&ecap0 {
+ status = "okay";
+};
---
base-commit: 8b7179210b22f8e48a82c5ceacb9d56a9c4cfec4
change-id: 20261104-v1_beagley-ai-lincolntech-lcd185-0ab3d7bda52f
Best regards,
--
Swamil Jain <s-jain1@xxxxxx>