Re: [PATCH v3 4/5] hwmon: sy7636a: read the temperature only while the rails are on

[Guenter Roeck]

On Sun, Nov 08, 2026 at 09:36:01AM +0000, Pablo Mazzini wrote:
> The driver enables VCOM at probe, which keeps the panel's high voltage
> rails on for good. Read the temperature only while the rails are on, when
> the chip samples it, and return -ENODATA otherwise. Read power good with
> it in one transfer, so the value can not be from before the first sample
> or after the rails went off. Register it under the chip name, as the
> TPS65185 and FP9931 drivers do.
> 
> Signed-off-by: Pablo Mazzini <pmazzini@xxxxxxxxx>
> ---
>  drivers/hwmon/sy7636a-hwmon.c | 37 +++++++++++++++++++++++------------
>  1 file changed, 25 insertions(+), 12 deletions(-)
> 
> diff --git a/drivers/hwmon/sy7636a-hwmon.c b/drivers/hwmon/sy7636a-hwmon.c
> index a6b47452e29e..0c0601d47b87 100644
> --- a/drivers/hwmon/sy7636a-hwmon.c
> +++ b/drivers/hwmon/sy7636a-hwmon.c
> @@ -9,26 +9,43 @@
>   */
>  
>  #include <linux/auxiliary_bus.h>
> +#include <linux/bits.h>
>  #include <linux/err.h>
>  #include <linux/hwmon.h>
>  #include <linux/module.h>
>  #include <linux/regmap.h>
> -#include <linux/regulator/machine.h>
>  
> -#define SY7636A_REG_TERMISTOR_READOUT	0x08
> +#define SY7636A_REG_FAULT_FLAG		0x07
> +#define SY7636A_FAULT_FLAG_PG		BIT(0)
>  
>  static int sy7636a_read(struct device *dev, enum hwmon_sensor_types type,
>  			u32 attr, int channel, long *temp)
>  {
>  	struct regmap *regmap = dev_get_drvdata(dev);
> -	int ret, reg_val;
> -
> -	ret = regmap_read(regmap,
> -			  SY7636A_REG_TERMISTOR_READOUT, &reg_val);
> +	u8 buf[2];
> +	int ret;
> +
> +	/*
> +	 * The thermistor is sampled while ON_OFF is set, but the first sample
> +	 * is only ready after the ADC sampling and conversion time (ADC_SPL +
> +	 * ADC_DEL in the datasheet); until then it holds its reset value, 0.
> +	 * PG is only set once all rails are up, after the first sample, so
> +	 * read it in the same transfer and report the temperature only while
> +	 * it is set.
> +	 *
> +	 * With ON_OFF set but PG low (rails still ramping up, or a fault), no
> +	 * temperature is reported even if one may be available. That is
> +	 * accepted: the display driver reads the temperature only while it
> +	 * holds the rails on, after power good.
> +	 */
> +	ret = regmap_bulk_read(regmap, SY7636A_REG_FAULT_FLAG, buf, sizeof(buf));
>  	if (ret)
>  		return ret;
>  
> -	*temp = (s8)reg_val * 1000;
> +	if (!(buf[0] & SY7636A_FAULT_FLAG_PG))
> +		return -ENODATA;
> +
> +	*temp = (s8)buf[1] * 1000;
>  
>  	return 0;
>  }
> @@ -72,12 +89,8 @@ static int sy7636a_sensor_probe(struct auxiliary_device *adev,
>  	if (!regmap)
>  		return -ENODEV;
>  
> -	err = devm_regulator_get_enable(&adev->dev, "vcom");
> -	if (err)
> -		return err;
> -
>  	hwmon_dev = devm_hwmon_device_register_with_info(&adev->dev,
> -							 "sy7636a_temperature", regmap,
> +							 "sy7636a", regmap,

This change is neither related to this patch nor necessary. Other drivers (unnecessarily)
doing the same is not an argument.

Guenter

>  							 &sy7636a_chip_info, NULL);
>  
>  	if (IS_ERR(hwmon_dev)) {