[PATCH 0/2] ARM: dts: zynq: Add ALINX AX7Z020B development board

[Pufan Jin]

This series adds device tree support for the ALINX AX7Z020B development
board, based on the Xilinx Zynq-7000 SoC (XC7Z020-2CLG400I).

Note: the "alinx" vendor prefix is not part of this series, it is already
present as commit 1f06cd374a60 ("dt-bindings: vendor-prefixes: Add ALINX
vendor prefix") in the Xilinx for-next branch.

The platform consists of two physical layers:

1. ALINX AC7Z020 system on module (SoM), in zynq-alinx-ac7z020.dtsi:
   - Xilinx XC7Z020-2CLG400I SoC (dual ARM Cortex-A9, 33.333333MHz PS_CLK)
   - 1024 MiB DDR3 SDRAM (2x MT41K256M16RE-125, 32-bit bus)
   - 32 MiB QSPI Flash (Winbond W25Q256FVEI) with 4 MTD partitions
   - DevCFG FPGA manager

2. The AX7Z020B board (AC7Z020 SoM plus carrier board), described in
   zynq-alinx-ax7z020b.dts:
   - Serial console via USB-UART bridge (CP2102, MIO 48-49)
   - MicroSD slot on SDHCI0 (MIO 40-45)
   - Gigabit Ethernet via GEM0 (MIO 16-27 RGMII, MIO 52-53 MDIO)
     with JLSemi JL2121 PHY at MDIO address 1 and RJ45 link/activity LEDs
   - USB 2.0 host via USB3320C ULPI PHY (MIO 28-39), reset on MIO 46
   - Dual CAN buses (CAN0 on MIO 10-11, CAN1 on MIO 12-13) with
     SN65HVD232 transceivers
   - I2C bus on MIO 50-51 with 24LC04 EEPROM, DS1338 RTC and LM75 sensor
   - 2x SMA AD inputs and a spare differential pair wired to XADC aux
     channels VAUX1/VAUX9/VAUX12. XADC is a hard macro accessible from the
     PS without PL configuration, the channels are enabled via the
     xlnx,channels property.

Tested on hardware: boot from SD card, UART console, SD card, GbE with
iperf3 (940+ Mbps) and netdev LED trigger hardware offload, USB host,
dual CAN (SocketCAN at 500 kbps), I2C sensors, QSPI flash MTD partitions,
and XADC temperature/voltage plus the external AD aux channels via IIO.

The DTB passes CHECK_DTBS=y and the bindings pass dt_binding_check.

Pufan Jin (2):
  dt-bindings: soc: xilinx: Add ALINX AX7Z020B board
  ARM: dts: zynq: Add ALINX AX7Z020B development board

 .../bindings/soc/xilinx/xilinx.yaml           |   6 +
 arch/arm/boot/dts/xilinx/Makefile             |   1 +
 .../boot/dts/xilinx/zynq-alinx-ac7z020.dtsi   |  72 +++++++++
 .../boot/dts/xilinx/zynq-alinx-ax7z020b.dts   | 137 ++++++++++++++++++
 4 files changed, 216 insertions(+)
 create mode 100644 arch/arm/boot/dts/xilinx/zynq-alinx-ac7z020.dtsi
 create mode 100644 arch/arm/boot/dts/xilinx/zynq-alinx-ax7z020b.dts

-- 
2.56.0