[PATCH v2 0/1] alpha/perf: Enable duration-based sampling throttling

From: Magnus Lindholm

Date: Tue Nov 10 2026 - 14:31:59 EST


Hi,

Changes in v2, following Matt's review:
- Describe the unresponsive-machine/RCU-starvation symptom in the commit.
- Include proto.h for est_cycle_freq and use cycles_t without the cast.
- Precompute the cycles-to-nanoseconds multiplier/shift and mark both
__ro_after_init, removing division from the interrupt path.
- Add Matt's Reviewed-by.

Both v2 mainline and ES40 integration builds passed (vmlinux, boot image
and modules), with only the existing saved_config COMMON-symbol warning.
Disassembly confirms no division call in either interrupt wrapper.
The multiplier conversion checks cover rounding, overflow and RPCC wrap.
The historical hardware results below apply to v1's division-based
conversion. V2 also passed seven bounded tests on the ES40 with the
alpha-devel integration: the 1024/s and 4096/s CPU0 controls, 1024/s
controls on CPUs 1 and 2, and period-17 tests starting at 100000/s on
each CPU. Duration feedback reduced the limits to 7168/s, 5120/s and
5120/s respectively. All 26156 samples were recorded without reported
loss, and no new RCU stalls or kernel faults appeared, including a
30-second observation after the final run. This does not repeat the
full v1 stress matrix below. The selected-frequency cleanup remains
outside this patch.

While testing Matt's v7 ProfileMe series [1] on my EV67 AlphaServer ES40,
I found that short-period sampling could make the machine unresponsive.
Once serial logging was enabled, the console showed RCU grace-period
kthread starvation reports. The failure also reproduced without my
generic-entry follow-up patches.

Count-based throttling was working: at HZ=1024 and the default limit of
100000 samples/s, the observed cadence was approximately 98 interrupts
per throttle cycle. However, Alpha never called perf_sample_event_took(),
so perf could not reduce that limit based on interrupt handling cost.
Setting perf_cpu_time_max_percent to 25 did not provide that feedback.

Keeping period 17 but lowering the limit to 1024 or 4096 samples/s made
the tests pass while still exercising repeated stop/park/restart cycles.
Adding duration feedback also made the original high-rate test pass,
without changing those counter-state operations. The minimal fix measured
average handler costs of 24-26 us against a 2.5 us budget and reduced the
limit to 7168-8192 samples/s.

Reproducer
==========

The reproducer requires Matt's ProfileMe kernel series and matching perf
tools. On the ES40 I used the following one-second workload, built
natively as "busy":

#include <stdint.h>
#include <time.h>

static double now(void)
{
struct timespec t;

clock_gettime(CLOCK_MONOTONIC, &t);
return t.tv_sec + t.tv_nsec * 1e-9;
}

int main(void)
{
uint64_t x = 1;
double end = now() + 1;

do {
for (int i = 0; i < 1000; i++)
asm volatile("mulq %0,3,%0" : "+r" (x));
} while (now() < end);
return 0;
}

cc -O2 -o busy busy.c

As root, with serial capture running:

dmesg -n 7
sysctl -w kernel.perf_event_max_sample_rate=100000
sysctl -w kernel.perf_cpu_time_max_percent=25

The period-10007 control completed successfully:

taskset -c 0 perf record -B -R \
-e cpu/instructions,profileme,randomize/ -c 10007 \
-o control.data -- ./busy

Changing only the period reproduced the failure:

taskset -c 0 perf record -B -R \
-e cpu/instructions,profileme,randomize/ -c 17 \
-o period17.data -- ./busy

The unpatched runs required a manual reset; a userspace timeout did not
reliably recover the system. The commands above are the essential
recording commands from the controlled tests, which also used a timeout
supervisor and saved logs on another machine.

Validation and submission scope
===============================

The v1 minimal fix, without diagnostic instrumentation, passed three
repeats of the high-rate reproducer and the two low-rate controls.
Broader testing covered 21 cases on all three CPUs: randomized ProfileMe
instruction sampling at periods 16, 17 and 31, ProfileMe and Aggregate
cycle sampling, and concurrent ProfileMe and mixed-mode workloads.
All completed, with 1352488 samples, no recorded losses and no new RCU
stalls or kernel faults. This was bounded stress testing, not a long soak.

The missing feedback predates ProfileMe. This patch is therefore based
on mainline and can be reviewed and applied independently of Matt's
series. I cross-built vmlinux, the Alpha boot image and modules on
mainline d48723711bae with the ES40 configuration and GCC 15.0.1. The
only build warning was the existing saved_config COMMON-symbol warning.

The hardware results above used Matt's v7 series with the v1 fix applied;
the mainline-only build has not been boot-tested. RPCC supplies a short,
same-CPU interval because Alpha's tick-based sched_clock() is too coarse
for this measurement. Counter programming and event handling are unchanged.

[1] https://lore.kernel.org/linux-alpha/20261105-alpha-profileme-v7-0-c474e892abb0@xxxxxxxxx/


Magnus Lindholm (1):
alpha/perf: Account for time spent handling PMU interrupts

arch/alpha/kernel/perf_event.c | 35 ++++++++++++++++++++++++++++++++--
1 file changed, 33 insertions(+), 2 deletions(-)

--
2.43.0