[PATCH] arm64: dts: qcom: eliza-mtp: Add WCD9390 USB-SS mux for DP alt mode

From: Balaji Kalkonda

Date: Thu Nov 12 2026 - 00:48:28 EST


The WCD9390 USB-SS mux routes the AUX/SBU lines between the USB-C
connector and the DP PHY, but eliza-mtp lacks the devicetree node for
it. Without a physical path for AUX, every DPCD probe times out and
the display never comes up:

msm_dpu ae01000.display-controller: [drm:drm_dp_dpcd_probe [drm_display_helper]] dpu_dp_aux: 0x00102 AUX -> (ret=-110)
msm_dpu ae01000.display-controller: [drm:msm_dp_bridge_hpd_notify [msm]] type=10 link hpd_link_status=0x0, status=2
[drm:msm_dp_bridge_detect [msm]] failed to read caps
[drm:msm_dp_bridge_detect [msm]] aux not connected

Add the wcd_usbss typec-mux node on i2c3, along with its supply and
reset line, and wire its SBU endpoint to a new port on the pmic-glink
connector. This gives the AUX/SBU signals a physical path from the
USB-C connector through the mux to the DP PHY.

Signed-off-by: Balaji Kalkonda <balaji.kalkonda@xxxxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/eliza-mtp.dts | 36 ++++++++++++++++++++++++++++++++++
1 file changed, 36 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/eliza-mtp.dts b/arch/arm64/boot/dts/qcom/eliza-mtp.dts
index ee05192adcfb..d848ae77ab85 100644
--- a/arch/arm64/boot/dts/qcom/eliza-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/eliza-mtp.dts
@@ -96,6 +96,14 @@ pmic_glink_ss_in: endpoint {
remote-endpoint = <&usb_dp_qmpphy_out>;
};
};
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_sbu: endpoint {
+ remote-endpoint = <&wcd_usbss_sbu_mux>;
+ };
+ };
};
};
};
@@ -112,6 +120,34 @@ vph_pwr: regulator-vph-pwr {
};
};

+&i2c3 {
+ status = "okay";
+
+ wcd_usbss: typec-mux@e {
+ compatible = "qcom,wcd9390-usbss";
+ reg = <0xe>;
+
+ vdd-supply = <&vreg_l7b>;
+ reset-gpios = <&tlmm 152 GPIO_ACTIVE_HIGH>;
+
+ mode-switch;
+ orientation-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ wcd_usbss_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_sbu>;
+ };
+ };
+ };
+ };
+};
+
&apps_rsc {
regulators-0 {
compatible = "qcom,pm7550-rpmh-regulators";

---
base-commit: 793807ca13bf3072fc6d16ce6d90e9ab9beff2a5
change-id: 20261111-eliza-wcd-mux-fix-453716a9c1a9

Best regards,
--
Balaji Kalkonda <balaji.kalkonda@xxxxxxxxxxxxxxxx>