Re: [PATCH v2 1/2] tpm: Disable a TPM that stops responding

From: Jarkko Sakkinen

Date: Thu Nov 12 2026 - 09:07:45 EST


On Thu, Nov 12, 2026 at 04:30:17AM -0800, Breno Leitao wrote:
> A TPM that stops responding fails each command only after the transport
> timeout, and its callers keep sending more: the hwrng thread every 10
> seconds forever, and userspace through /dev/tpmrm0. Each attempt holds
> tpm_mutex for the whole timeout and logs an error:
>
> tpm tpm0: invalid TPM_STS.x 0xff, dumping stack for forensics
> tpm tpm0: tpm_try_transmit: send(): error -62
> tpm tpm0: tpm_try_transmit: send(): error -62
> ...
>
> The core already stops using a TPM it cannot trust: tpm_try_get_ops()
> fails with -EIO once TPM_CHIP_FLAG_DISABLE is set, which
> tpm2_load_null() does when it cannot restore the null key. Set the same
> flag once 60 commands in a row have timed out.
>
> A completed command, whatever its TPM return code, resets the count.
> Some TPMs stall for half a minute, time out a handful of commands, and
> then recover, so a short streak must not disable them.
>
> With only the hwrng retrying every 10 seconds, 60 timeouts take more
> than ten minutes. A userspace poller gets there sooner, but each of its
> commands still waits out the transport timeout.
>
> The limit is the tpm.max_unanswered boot parameter, so that slow
> pre-production parts, such as FPGA prototypes, can raise it, or set it
> to 0 to never disable the TPM. A disabled TPM stays disabled until the
> driver is rebound or the machine reboots.
>
> Signed-off-by: Breno Leitao <leitao@xxxxxxxxxx>
> ---
> drivers/char/tpm/tpm-interface.c | 15 +++++++++++++++
> include/linux/tpm.h | 1 +
> 2 files changed, 16 insertions(+)
>
> diff --git a/drivers/char/tpm/tpm-interface.c b/drivers/char/tpm/tpm-interface.c
> index e0385b16616b46..b7865ccb799289 100644
> --- a/drivers/char/tpm/tpm-interface.c
> +++ b/drivers/char/tpm/tpm-interface.c
> @@ -40,6 +40,11 @@ module_param_named(suspend_pcr, tpm_suspend_pcr, uint, 0644);
> MODULE_PARM_DESC(suspend_pcr,
> "PCR to use for dummy writes to facilitate flush on suspend.");
>
> +static unsigned int tpm_max_unanswered = 60;
> +module_param_named(max_unanswered, tpm_max_unanswered, uint, 0444);
> +MODULE_PARM_DESC(max_unanswered,
> + "Disable the TPM after this many commands in a row time out (0 = never).");

Documentation/admin/kernel-parameters.txt update is also needed.

tpm_max_missed_responses is what I would suggest, because it is more
accurate e.g., on stating what is being counted :-)


> +
> /**
> * tpm_calc_ordinal_duration() - calculate the maximum command duration
> * @chip: TPM chip to use.
> @@ -268,6 +273,16 @@ ssize_t tpm_transmit(struct tpm_chip *chip, u8 *buf, size_t bufsiz)
> delay_msec *= 2;
> memcpy(buf, save, save_size);
> }
> +
> + if (ret >= 0) {
> + /* we are good, reset nr_unanswered */

I'm not a huge fan in general of third person plural in the source code
comments. Probably a comment here is not needed at all as it does not
state anything that would not be obvious (i.e. something nothing
non-obvious is documented).

> + chip->nr_unanswered = 0;
> + } else if (ret == -ETIME &&
> + ++chip->nr_unanswered == tpm_max_unanswered) {
> + dev_err(&chip->dev, "%u commands in a row timed out, disabling the TPM\n",
> + chip->nr_unanswered);
> + chip->flags |= TPM_CHIP_FLAG_DISABLE;
> + }
> return ret;
> }
>
> diff --git a/include/linux/tpm.h b/include/linux/tpm.h
> index 0db277af45c393..e8191585a68e7a 100644
> --- a/include/linux/tpm.h
> +++ b/include/linux/tpm.h
> @@ -131,6 +131,7 @@ struct tpm_chip {
> struct hwrng hwrng;
>
> struct mutex tpm_mutex; /* tpm is processing */
> + unsigned int nr_unanswered; /* commands in a row that timed out */

This would be then nr_lost_responses.

>
> unsigned long timeout_a; /* jiffies */
> unsigned long timeout_b; /* jiffies */
>
> --
> 2.53.0-Meta
>

Br, Jarkko