[PATCH v3 0/2] ARM: dts: zynq: Add ALINX AX7Z020B development board

From: Pufan Jin

Date: Thu Nov 12 2026 - 18:34:06 EST


Add devicetree support for the ALINX AX7Z020B board, built around the
ALINX AC7Z020 system on module with a Zynq-7000 (XC7Z020-2CLG400I) SoC.

Changes in v3:
- Drop the vendor website Link: tags (Krzysztof Kozlowski).
- Drop the empty bootargs property (Krzysztof Kozlowski).
- Rename the USB PHY node from phy0 to phy, as there is only one USB PHY
on the board (Krzysztof Kozlowski).
- Keep the explicit mdio node under gem0, as requested during the v1
review and reviewed by Andrew Lunn in v2. dtc W=1 flags the parent
node's inherited #address-cells/#size-cells. DT schema validation
reports the same Zynq-7000 diagnostics as zynq-zybo-z7. The MDIO
layout was also verified on hardware.
- Sort I2C child nodes by address and reorder status/reg properties.
- Add Krzysztof's Acked-by to patch 1.

The "alinx" vendor prefix is already queued in linux-next as commit
1f06cd374a60 ("dt-bindings: vendor-prefixes: Add ALINX vendor prefix"),
so it is not part of this series.

Tested on hardware before the DTS style reordering: SD boot, UART
console, SD card, GbE (900+ Mbps and LED hardware offload), dual CAN,
I2C, QSPI and XADC.

Pufan Jin (2):
dt-bindings: soc: xilinx: Add ALINX AX7Z020B board
ARM: dts: zynq: Add ALINX AX7Z020B development board

.../bindings/soc/xilinx/xilinx.yaml | 5 +
arch/arm/boot/dts/xilinx/Makefile | 1 +
.../boot/dts/xilinx/zynq-alinx-ac7z020.dtsi | 71 +++++++++
.../boot/dts/xilinx/zynq-alinx-ax7z020b.dts | 146 ++++++++++++++++++
4 files changed, 223 insertions(+)
create mode 100644 arch/arm/boot/dts/xilinx/zynq-alinx-ac7z020.dtsi
create mode 100644 arch/arm/boot/dts/xilinx/zynq-alinx-ax7z020b.dts

Range-diff against v2:
1: f44b8dc6e6 ! 1: ca50a01108 dt-bindings: soc: xilinx: Add ALINX AX7Z020B board
@@ Commit message
Document the ALINX AX7Z020B development board, built around the ALINX
AC7Z020 system on module.

- Link: https://www.alinx.com/
Signed-off-by: Pufan Jin <cyan2254650260@xxxxxxxxx>
+ Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxxxxxxxx>

## Documentation/devicetree/bindings/soc/xilinx/xilinx.yaml ##
@@ Documentation/devicetree/bindings/soc/xilinx/xilinx.yaml: properties:
2: a985ee80d4 ! 2: 477061f136 ARM: dts: zynq: Add ALINX AX7Z020B development board
@@ Commit message
always accessible from the PS, so expose these channels via the
driver's xlnx,channels property.

- Link: https://www.alinx.com/
Signed-off-by: Pufan Jin <cyan2254650260@xxxxxxxxx>

## arch/arm/boot/dts/xilinx/Makefile ##
@@ arch/arm/boot/dts/xilinx/zynq-alinx-ac7z020.dtsi (new)
+
+&qspi {
+ bootph-all;
-+ status = "okay";
+ num-cs = <1>;
+
++ status = "okay";
++
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
@@ arch/arm/boot/dts/xilinx/zynq-alinx-ac7z020.dtsi (new)
+ #size-cells = <1>;
+
+ partition@0 {
-+ label = "boot";
+ reg = <0x00000000 0x00500000>;
++ label = "boot";
+ };
+
+ partition@500000 {
-+ label = "bootenv";
+ reg = <0x00500000 0x00020000>;
++ label = "bootenv";
+ };
+
+ partition@520000 {
-+ label = "image";
+ reg = <0x00520000 0x00a80000>;
++ label = "image";
+ };
+
+ partition@fa0000 {
-+ label = "spare";
+ reg = <0x00fa0000 0x01060000>;
++ label = "spare";
+ };
+ };
+ };
@@ arch/arm/boot/dts/xilinx/zynq-alinx-ax7z020b.dts (new)
+ };
+
+ chosen {
-+ bootargs = "";
+ stdout-path = "serial0:115200n8";
+ };
+
-+ usb_phy0: phy0 {
++ usb_phy0: phy {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ reset-gpios = <&gpio0 46 GPIO_ACTIVE_LOW>;
@@ arch/arm/boot/dts/xilinx/zynq-alinx-ax7z020b.dts (new)
+};
+
+&gem0 {
-+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <&ethernet_phy>;
+
++ status = "okay";
++
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
@@ arch/arm/boot/dts/xilinx/zynq-alinx-ax7z020b.dts (new)
+};
+
+&i2c0 {
-+ status = "okay";
+ clock-frequency = <100000>;
+
++ status = "okay";
++
++ temperature-sensor@48 {
++ compatible = "national,lm75";
++ reg = <0x48>;
++ };
++
+ eeprom@50 {
+ compatible = "atmel,24c04";
+ reg = <0x50>;
@@ arch/arm/boot/dts/xilinx/zynq-alinx-ax7z020b.dts (new)
+ compatible = "dallas,ds1338";
+ reg = <0x68>;
+ };
-+
-+ temperature-sensor@48 {
-+ compatible = "national,lm75";
-+ reg = <0x48>;
-+ };
+};
+
+&sdhci0 {
+ bootph-all;
-+ status = "okay";
+ disable-wp;
++
++ status = "okay";
+};
+
+&uart0 {
@@ arch/arm/boot/dts/xilinx/zynq-alinx-ax7z020b.dts (new)
+
+&uart1 {
+ bootph-all;
++
+ status = "okay";
+};
+
+&usb0 {
-+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy0>;
++
++ status = "okay";
+};

--
2.56.0