Re: [PATCH v2 2/2] ARM: dts: zynq: Add ALINX AX7Z020B development board

From: Pufan Jin

Date: Thu Nov 12 2026 - 19:07:36 EST



On 11/12/26 7:08 PM, Krzysztof Kozlowski wrote:
On Wed, Nov 11, 2026 at 11:29:17AM -0500, Pufan Jin wrote:
Add devicetree support for the ALINX AX7Z020B development board.
The board is built around the ALINX AC7Z020 system on module with a
Zynq-7000 (XC7Z020-2CLG400I) SoC, 1 GB DDR3 SDRAM and 32 MB QSPI
flash, and provides Gigabit Ethernet (JLSemi JL2121 PHY), USB 2.0
host, MicroSD slot, dual CAN buses (SN65HVD232 transceivers on
MIO 10-13), I2C RTC/EEPROM/LM75 and the serial console on UART1.
DevCFG FPGA manager is also enabled.

The two SMA AD inputs and the spare differential pair are wired to
XADC aux channels VAUX1, VAUX9 and VAUX12. The XADC hard macro is
always accessible from the PS, so expose these channels via the
driver's xlnx,channels property.

Link: https://www.alinx.com/
Drop link. We do not advertise websites, unless it brings some value.

Signed-off-by: Pufan Jin <cyan2254650260@xxxxxxxxx>
---
arch/arm/boot/dts/xilinx/Makefile | 1 +
.../boot/dts/xilinx/zynq-alinx-ac7z020.dtsi | 70 +++++++++
.../boot/dts/xilinx/zynq-alinx-ax7z020b.dts | 142 ++++++++++++++++++
3 files changed, 213 insertions(+)
create mode 100644 arch/arm/boot/dts/xilinx/zynq-alinx-ac7z020.dtsi
create mode 100644 arch/arm/boot/dts/xilinx/zynq-alinx-ax7z020b.dts
...

diff --git a/arch/arm/boot/dts/xilinx/zynq-alinx-ax7z020b.dts b/arch/arm/boot/dts/xilinx/zynq-alinx-ax7z020b.dts
new file mode 100644
index 0000000000..472d9fcaaf
--- /dev/null
+++ b/arch/arm/boot/dts/xilinx/zynq-alinx-ax7z020b.dts
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * DTS for ALINX AX7Z020B Development Board
+ *
+ * Copyright (C) 2026 Pufan Jin <cyan2254650260@xxxxxxxxx>
+ */
+
+/dts-v1/;
+#include "zynq-alinx-ac7z020.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "ALINX AX7Z020B Development Board";
+ compatible = "alinx,ax7z020b", "alinx,ac7z020", "xlnx,zynq-7000";
+
+ aliases {
+ ethernet0 = &gem0;
+ serial0 = &uart1;
+ serial1 = &uart0;
+ mmc0 = &sdhci0;
+ spi0 = &qspi;
+ i2c0 = &i2c0;
+ };
+
+ chosen {
+ bootargs = "";
Drop bootargs, why do you need empty ones anyway?


+ stdout-path = "serial0:115200n8";
+ };
+
+ usb_phy0: phy0 {
just "phy" or is there phy-1?

Best regards,
Krzysztof


Drop link. We do not advertise websites, unless it brings some value.
Agreed. I've removed the link in v3.

Drop bootargs, why do you need empty ones anyway?

The empty bootargs is not needed. I've removed it.

just "phy" or is there phy-1?

There is only one USB PHY on this board. I've renamed the node to "phy".

Thanks for the review!

Pufan Jin