[PATCH 1/7] arm64: dts: qcom: lemans-draco-evk: Add LT9611UXD HDMI bridge support

From: Mohit Dsor

Date: Fri Nov 13 2026 - 11:44:23 EST


Add support for the Lontium LT9611UXD DSI-to-HDMI bridge on the base
board DT to provide HDMI output via the LT9611UXD daughter card.

LT9611UXD is connected through I2C mux channel 0 on i2c1, with reset
and interrupt on GPIO39 and GPIO97 respectively, powered by fixed
regulators on expander2. DIP Switch SW2.4 need to be ON for this to
work.

Signed-off-by: Mohit Dsor <mohit.dsor@xxxxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/lemans-draco-evk.dts | 118 ++++++++++++++++++++++++++
1 file changed, 118 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/lemans-draco-evk.dts b/arch/arm64/boot/dts/qcom/lemans-draco-evk.dts
index 5238157ad002..89beed7de36b 100644
--- a/arch/arm64/boot/dts/qcom/lemans-draco-evk.dts
+++ b/arch/arm64/boot/dts/qcom/lemans-draco-evk.dts
@@ -16,6 +16,7 @@ / {
aliases {
ethernet0 = &ethernet0;
ethernet1 = &ethernet1;
+ i2c1 = &i2c1;
};

dp0-connector {
@@ -74,6 +75,34 @@ dp3_connector_in: endpoint {
};
};

+ hdmi_connector: hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_out: endpoint {
+ remote-endpoint = <&hdmi_bridge_out>;
+ };
+ };
+ };
+
+ vreg_bridge_1p2: regulator-bridge-1p2 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_bridge_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ vin-supply = <&vreg_bridge_3p3>;
+ };
+
+ vreg_bridge_3p3: regulator-bridge-3p3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_bridge_3p3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&expander2 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
vreg_dp0_pwr: regulator-dp0-pwr {
compatible = "regulator-fixed";
regulator-name = "VREG_DP0_PWR_3P3";
@@ -115,6 +144,63 @@ vreg_dp3_pwr: regulator-dp3-pwr {
};
};

+&i2c1 {
+ status = "okay";
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9548";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ vdd-supply = <&vreg_s4a>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hdmi_bridge: hdmi-bridge@41 {
+ compatible = "lontium,lt9611uxd";
+ reg = <0x41>;
+
+ interrupts-extended = <&tlmm 97 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_bridge_3p3>;
+ vdd-supply = <&vreg_bridge_1p2>;
+
+ pinctrl-0 = <&bridge_rst_pin &bridge_irq_pin>;
+ pinctrl-names = "default";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ hdmi_bridge_in0: endpoint {
+ remote-endpoint = <&mdss0_dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ hdmi_bridge_in1: endpoint {
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ hdmi_bridge_out: endpoint {
+ remote-endpoint = <&hdmi_connector_out>;
+ };
+ };
+ };
+ };
+ };
+ };
+};
+
&i2c2 {
status = "okay";

@@ -156,6 +242,21 @@ expander4: gpio@38 {

&tlmm {

+ bridge_rst_pin: bridge-rst-state {
+ pins = "gpio39";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ output-high;
+ };
+
+ bridge_irq_pin: bridge-irq-state {
+ pins = "gpio97";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
dp2_hot_plug_det: dp2-hot-plug-det-state {
pins = "gpio104";
function = "edp2_hot";
@@ -308,6 +409,23 @@ &mdss0_dp1_phy {
status = "okay";
};

+&mdss0_dsi0 {
+ vdda-supply = <&vreg_l1c>;
+
+ status = "okay";
+};
+
+&mdss0_dsi0_out {
+ data-lanes = <0 1 2 3>;
+ remote-endpoint = <&hdmi_bridge_in0>;
+};
+
+&mdss0_dsi0_phy {
+ vdds-supply = <&vreg_l4a>;
+
+ status = "okay";
+};
+
&mdss1 {
status = "okay";
};

--
2.34.1