[PATCH v7 17/23] arm64: dts: qcom: sm8750-qrd: Enable S5KJN1 camera sensor

From: Wenmeng Liu

Date: Sat Nov 14 2026 - 06:33:28 EST


Enable CAMSS, CCI1 and CSIPHY3 on the SM8750 QRD board. The S5KJN1
camera sensor is connected to CCI1 I2C bus 0, uses MCLK3 at 24 MHz and
connects to CSIPHY3 over a 4-lane D-PHY link.

Signed-off-by: Wenmeng Liu <wenmeng.liu@xxxxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sm8750-qrd.dts | 72 +++++++++++++++++++++++++++++++++
1 file changed, 72 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8750-qrd.dts b/arch/arm64/boot/dts/qcom/sm8750-qrd.dts
index 75927e1f7b9ab0316781c64dbcc82d3394c414f6..c92a1f3c47bd5cbae26854614682c3bc7daa0398 100644
--- a/arch/arm64/boot/dts/qcom/sm8750-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8750-qrd.dts
@@ -7,6 +7,7 @@

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
+#include <dt-bindings/media/video-interfaces.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "sm8750.dtsi"
#include "pm8010.dtsi"
@@ -858,6 +859,70 @@ vreg_l7n_3p3: ldo7 {
};
};

+&camss {
+ status = "okay";
+};
+
+&camss_csiphy3_in_port {
+ camss_csiphy3_inep: endpoint {
+ data-lanes = <1 2 3 4>;
+ remote-endpoint = <&csiphy3_out_ep>;
+ };
+};
+
+&cci1 {
+ status = "okay";
+};
+
+&cci1_i2c0 {
+ camera@56 {
+ compatible = "samsung,s5kjn1";
+ reg = <0x56>;
+
+ reset-gpios = <&tlmm 109 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&cam_mclk3_default &cam3_reset_default>;
+ pinctrl-names = "default";
+
+ clocks = <&cambistmclkcc CAM_BIST_MCLK_CC_MCLK3_CLK>;
+ assigned-clocks = <&cambistmclkcc CAM_BIST_MCLK_CC_MCLK3_CLK>;
+ assigned-clock-rates = <24000000>;
+
+ vdda-supply = <&vreg_l4m_2p8>;
+ vddd-supply = <&vreg_l2m_1p056>;
+ vddio-supply = <&vreg_l5m_1p8>;
+
+ port {
+ s5kjn1_out_ep: endpoint {
+ data-lanes = <1 2 3 4>;
+ link-frequencies = /bits/ 64 <700000000>;
+ remote-endpoint = <&csiphy3_in_ep>;
+ };
+ };
+ };
+};
+
+&csiphy3 {
+ vdda-0p9-supply = <&vreg_l1f_0p88>;
+ vdda-1p2-supply = <&vreg_l3g_1p2>;
+
+ status = "okay";
+};
+
+&csiphy3_in_port {
+ csiphy3_in_ep: endpoint {
+ bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
+ clock-lanes = <0>;
+ data-lanes = <1 2 3 4>;
+ remote-endpoint = <&s5kjn1_out_ep>;
+ };
+};
+
+&csiphy3_out_port {
+ csiphy3_out_ep: endpoint {
+ remote-endpoint = <&camss_csiphy3_inep>;
+ };
+};
+
&gpu {
status = "okay";
};
@@ -1081,6 +1146,13 @@ &tlmm {
/* reserved for secure world */
gpio-reserved-ranges = <36 4>, <74 1>;

+ cam3_reset_default: cam3-reset-default-state {
+ pins = "gpio109";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
sdc2_card_det_n: sd-card-det-n-state {
pins = "gpio55";
function = "gpio";

--
2.34.1