Re: [PATCH v3 2/2] arm64: dts: allwinner: h6: Add Orange Pi 3 LTS
From: Chen-Yu Tsai
Date: Sun Nov 15 2026 - 05:14:42 EST
On Tue, Oct 27, 2026 at 7:34 AM Cristian Filipescu via B4 Relay
<devnull+filipescu.cristian.gmail.com@xxxxxxxxxx> wrote:
>
> From: Jernej Skrabec <jernej.skrabec@xxxxxxxxx>
>
> Add the board description for the Allwinner H6-based Orange Pi 3 LTS,
> including its regulators, storage, Ethernet PHY, LEDs and USB ports.
>
> Specify the Motorcomm YT8531C PHY ID to avoid early ID autodetection,
> which failed on MAC driver rebind. Reset the sole PHY at MDIO bus
> registration and keep reset outside interface detach so its configured
> 125 MHz clock output is retained. Use PHY-internal RGMII delays.
>
> Select the weakest GPIO drive level for both LEDs. Enable 1.8 V eMMC
> DDR52 and HS200 modes; retain the H6 maximum frequency of 150 MHz.
>
> Link: https://lore.kernel.org/linux-sunxi/20250413134318.66681-3-jernej.skrabec@xxxxxxxxx/
> Signed-off-by: Jernej Skrabec <jernej.skrabec@xxxxxxxxx>
> Signed-off-by: Cristian Filipescu <filipescu.cristian@xxxxxxxxx>
> ---
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../dts/allwinner/sun50i-h6-orangepi-3-lts.dts | 379 +++++++++++++++++++++
> 2 files changed, 380 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index aa21f58a4..7ea136380 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -41,6 +41,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-beelink-gs1.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-3.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-3-lts.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3-lts.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3-lts.dts
> new file mode 100644
> index 000000000..e2ca41b94
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3-lts.dts
> @@ -0,0 +1,379 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +// Copyright (C) 2025 Jernej Skrabec <jernej.skrabec@xxxxxxxxx>
> +// Based on sun50i-h6-orangepi-3.dts, which is:
> +// Copyright (C) 2019 Ondřej Jirman <megous@xxxxxxxxxx>
We now have a common sun50i-h6-orangepi.dtsi file. You really should
rewrite this patch to just use that as a base. It is mostly the same
across all the OrangePi H6 boards.
> +
> +/dts-v1/;
> +
> +#include "sun50i-h6.dtsi"
> +#include "sun50i-h6-cpu-opp.dtsi"
> +#include "sun50i-h6-gpu-opp.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> + model = "OrangePi 3 LTS";
> + compatible = "xunlong,orangepi-3-lts", "allwinner,sun50i-h6";
> +
> + aliases {
> + ethernet0 = &emac;
> + ethernet1 = &aw859a;
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + connector {
> + compatible = "hdmi-connector";
> + ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
> + type = "a";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> + ext_osc32k: ext-osc32k-clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <32768>;
> + clock-output-names = "ext-osc32k";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led-0 {
> + function = LED_FUNCTION_STATUS;
The schematic (v1.4) calls this the "PWR" LED.
> + color = <LED_COLOR_ID_RED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_red_pin>;
> + gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> + };
> +
> + led-1 {
> + function = LED_FUNCTION_POWER;
And this one the "STATUS" LED. So you have the two functions swapped.
> + color = <LED_COLOR_ID_GREEN>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_green_pin>;
> + gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */
> + default-state = "on";
And this should go to the power LED.
> + };
> + };
> +
> + reg_gmac_3v3: gmac-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "gmac-3v3";
> + vin-supply = <®_vcc5v>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + startup-delay-us = <150000>;
> + enable-active-high;
> + gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
> + };
> +
> + reg_vcc5v: vcc5v {
> + /* board wide 5V supply directly from the DC jack */
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-5v";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + reg_wifi_3v3: wifi-3v3 {
> + /* 3.3V regulator for WiFi and BT */
> + compatible = "regulator-fixed";
> + regulator-name = "wifi-3v3";
> + vin-supply = <®_vcc5v>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + enable-active-high;
> + gpio = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
> + };
> +
> + wifi_pwrseq: wifi-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&rtc CLK_OSC32K_FANOUT>;
> + clock-names = "ext_clock";
> + reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
> + post-power-on-delay-ms = <200>;
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <®_dcdca>;
> +};
Set the supply on all cores.
> +
> +&de {
> + status = "okay";
> +};
> +
> +&dwc3 {
> + status = "okay";
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci3 {
> + status = "okay";
> +};
> +
> +&emac {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ext_rgmii_pins>;
> + phy-mode = "rgmii-id";
> + phy-handle = <&ext_rgmii_phy>;
> + phy-supply = <®_gmac_3v3>;
> + allwinner,rx-delay-ps = <0>;
> + allwinner,tx-delay-ps = <0>;
> + status = "okay";
> +};
> +
> +&gpu {
> + mali-supply = <®_dcdcc>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + hvcc-supply = <®_bldo2>;
> + status = "okay";
> +};
> +
> +&hdmi_out {
> + hdmi_out_con: endpoint {
> + remote-endpoint = <&hdmi_con_in>;
> + };
> +};
> +
> +&mdio {
> + reset-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */
> + reset-delay-us = <15000>;
> + reset-post-delay-us = <100000>;
> +
> + ext_rgmii_phy: ethernet-phy@1 {
> + compatible = "ethernet-phy-id4f51.e91b";
> + reg = <1>;
> +
> + motorcomm,clk-out-frequency-hz = <125000000>;
> + rx-internal-delay-ps = <1950>;
> + tx-internal-delay-ps = <1950>;
> + };
> +};
> +
> +&mmc0 {
> + vmmc-supply = <®_cldo1>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> + disable-wp;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&mmc1 {
> + vmmc-supply = <®_wifi_3v3>;
> + vqmmc-supply = <®_bldo3>;
Something is fishy here. The schematic also shows vcc-wifi-io (on the aw859
side) directly derived from vcc-wifi (reg_wifi_3v3). I suggest at least
checking with a multimeter to confirm what the voltage is on the VDDIO
pin of the module.
> + mmc-pwrseq = <&wifi_pwrseq>;
> + bus-width = <4>;
> + non-removable;
> + status = "okay";
> +
> + aw859a: wifi@1 {
> + reg = <1>;
> + };
> +};
> +
> +&mmc2 {
> + vmmc-supply = <®_cldo1>;
> + vqmmc-supply = <®_bldo2>;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> + cap-mmc-hw-reset;
> + non-removable;
> + bus-width = <8>;
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&ohci3 {
> + status = "okay";
> +};
> +
> +&pio {
> + vcc-pc-supply = <®_bldo2>;
> + vcc-pd-supply = <®_cldo1>;
> + vcc-pg-supply = <®_bldo3>;
> +};
> +
> +&r_ir {
> + status = "okay";
> +};
> +
> +&r_pio {
> + vcc-pm-supply = <®_bldo3>;
> +
> + led_green_pin: led-green-pin {
> + pins = "PL7";
> + function = "gpio_out";
> + drive-strength = <10>;
> + };
> +
> + led_red_pin: led-red-pin {
> + pins = "PL4";
> + function = "gpio_out";
> + drive-strength = <10>;
> + };
> +};
> +
> +&r_i2c {
> + status = "okay";
> +
> + axp805: pmic@36 {
> + compatible = "x-powers,axp805", "x-powers,axp806";
> + reg = <0x36>;
> + interrupt-parent = <&r_intc>;
> + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + x-powers,self-working-mode;
> + vina-supply = <®_vcc5v>;
> + vinb-supply = <®_vcc5v>;
> + vinc-supply = <®_vcc5v>;
> + vind-supply = <®_vcc5v>;
> + vine-supply = <®_vcc5v>;
> + aldoin-supply = <®_vcc5v>;
> + bldoin-supply = <®_vcc5v>;
> + cldoin-supply = <®_vcc5v>;
> +
> + regulators {
> + reg_aldo1: aldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-pl-led-ir";
> + };
> +
> + reg_aldo2: aldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc33-audio-tv-ephy-mac";
> + };
> +
> + /* ALDO3 is shorted to CLDO1 */
> + reg_aldo3: aldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc33-io-pd-emmc-sd-usb-uart-1";
> + };
> +
> + reg_bldo1: bldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18-dram-bias-pll";
> + };
> +
> + reg_bldo2: bldo2 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-efuse-pcie-hdmi-pc";
> + };
> +
> + reg_bldo3: bldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-pm-pg-dcxoio-wifi";
> + };
> +
> + bldo4 {
> + /* unused */
> + };
> +
> + reg_cldo1: cldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc33-io-pd-emmc-sd-usb-uart-2";
> + };
> +
> + cldo2 {
> + /* unused */
> + };
> +
> + cldo3 {
> + /* unused */
> + };
> +
> + /* DCDCB is polyphased with DCDCA. */
> + reg_dcdca: dcdca {
> + regulator-always-on;
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1160000>;
> + regulator-ramp-delay = <2500>;
> + regulator-name = "vdd-cpu";
> + };
> +
> + reg_dcdcc: dcdcc {
> + regulator-enable-ramp-delay = <32000>;
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-ramp-delay = <2500>;
> + regulator-name = "vdd-gpu";
> + };
> +
> + reg_dcdcd: dcdcd {
> + regulator-always-on;
> + regulator-min-microvolt = <960000>;
> + regulator-max-microvolt = <960000>;
> + regulator-name = "vdd-sys";
> + };
> +
> + reg_dcdce: dcdce {
> + regulator-always-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vcc-dram";
> + };
> +
> + sw {
> + /* unused */
> + };
> + };
> + };
> +};
> +
> +&rtc {
> + clocks = <&ext_osc32k>;
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_ph_pins>;
> + status = "okay";
> +};
> +
> +&usb2otg {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usb2phy {
> + usb0_id_det-gpios = <&pio 2 15 GPIO_ACTIVE_HIGH>; /* PC15 */
This isn't connected to anything but a pull-up. And you already specified
host mode only above.
ChenYu
> + usb0_vbus-supply = <®_vcc5v>;
> + usb3_vbus-supply = <®_vcc5v>;
> + status = "okay";
> +};
> +
> +&usb3phy {
> + status = "okay";
> +};
>
> --
> 2.47.3
>
>