[PATCH net-next v2 0/3] net: dsa: make a shorter bridge ageing time take effect
From: Oleksij Rempel
Date: Sun Nov 15 2026 - 06:00:30 EST
During an STP topology change, the bridge lowers the ageing time so
that stale FDB entries go away quickly. When the change is over, the
bridge sets the configured value again. On DSA switches, both steps
can go wrong:
- On a KSZ9893, ksz9477 does not apply a shorter value at once. Patch 1
fixes this.
- The DSA core can keep the short value after the bridge has restored
the long one. Patch 2 fixes this, and patch 3 does the same for a
port that has left the bridge.
In a lab test on a KSZ9893, I cut one of two redundant paths while a
station sent one-way UDP or raw Ethernet traffic. Without the series,
the traffic stopped for up to 56 s, long after STP had converged. With
it, the traffic came back after 12 to 15 s, about as long as STP
needed to converge.
One case is not fixed. The last port of a bridge in its DSA tree may
leave while the bridge has a shorter ageing time, for example during a
topology change. Then the switch keeps the short value until a bridge
with ports in the same DSA tree sets its ageing time, or a port in that
tree joins a bridge.
The patches carry Fixes tags. They still go to net-next, because
patches 2 and 3 change the DSA core and affect every driver with
.set_ageing_time.
With patch 2, sja1105 reloads its static config once more when the
bridge restores the ageing time.
To check patches 2 and 3 on a KSZ9477-family switch over I2C, read the
ageing register from debugfs (<device> is the I2C device, for example
3-005f):
dd if=/sys/kernel/debug/regmap/<device>-32/registers bs=15 \
skip=$((0x310)) count=1 2>/dev/null
The ageing time in seconds is bits 5:3 of the first byte times the last
byte. For example, in "0310: 55450096" bits 5:3 of 0x55 give 2 and 0x96
is 150, so the ageing time is 2 x 150 s = 300 s.
Without STP, after a boot (the comments give the register value):
ip link add br0 type bridge stp_state 0
ip link set lan1 master br0
ip link set lan2 master br0
ip link set br0 up
ip link set br0 type bridge ageing_time 1000 # 10 s
# 0310: 4d45000a (1 x 10 s)
ip link set lan2 nomaster
ip link set br0 type bridge ageing_time 30000 # 300 s
# with the series: 0310: 55450096 (2 x 150 s)
# without patch 2 or 3: 0310: 4d45000a (1 x 10 s)
With kernel STP, start again with a bridge that runs STP, here with
forward_delay 4 s. lan1 and lan2 need a link to peers that do not run
STP, so that br0 is the root bridge:
ip link del br0
ip link add br0 type bridge stp_state 1 forward_delay 400
ip link set lan1 master br0
ip link set lan2 master br0
ip link set lan1 up
ip link set lan2 up
ip link set br0 up
# wait until /sys/class/net/br0/bridge/topology_change reads 1
# 0310: 55450004 (2 x 4 s)
ip link set lan2 nomaster
sleep 30
# with the series: 0310: 55450096 (2 x 150 s)
# without patch 2 or 3: 0310: 55450004 (2 x 4 s)
Tested on a KSZ9893.
---
Changes in v2:
- Link to v1: https://lore.kernel.org/r/20261104-ksz-stp-ageing-v1-0-2c2bc7217dea@xxxxxxxxxxxxxx
---
Oleksij Rempel (3):
net: dsa: microchip: ksz9477: apply a shorter ageing time at once
net: dsa: ignore the old ageing time of the port being changed
net: dsa: forget the port ageing time when the port leaves the bridge
drivers/net/dsa/microchip/ksz9477.c | 41 ++++++++++++++++++++++++++++++++-----
net/dsa/port.c | 13 +++++++++---
net/dsa/switch.c | 17 +++++++++++----
net/dsa/switch.h | 1 +
4 files changed, 60 insertions(+), 12 deletions(-)
---
base-commit: 6964ff21c5d8b75649211a52dbfd92753e605649
change-id: 20261103-ksz-stp-ageing-705aa69829e5
Best regards,
--
Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>