[PATCH v4 0/2] i2c: Add Cortina Systems CS75xx I2C controller driver
From: Fil Dunsky via B4 Relay
Date: Sun Nov 15 2026 - 11:55:49 EST
The I2C ("Bi-Wire") controller of the Cortina Systems CS75xx
("Goldengate G2") SoCs transfers one byte per command, with a command
register much like the OpenCores one, and raises an interrupt when a
command has completed. This series adds the binding and a driver for
plain I2C and emulated SMBus, without quick commands (every message
carries at least one data byte) and without 10-bit addresses.
The driver used to be part of a series with the interrupt controller,
GPIO and watchdog drivers and the device tree changes. That series is
now split per subsystem: the driver builds with COMPILE_TEST and does
not depend on the platform series [1], which is under review separately.
The device tree nodes will follow with the other CS75xx dts changes once
the platform is merged.
There is no public documentation; the register layout comes from the GPL
vendor kernels. Tested on a Securifi Almond+ (CS7542) with the SX8650
touchscreen controller at 0x48: reads are ACKed, an empty address returns
-ENXIO without timeouts. Repeated START between messages has not been
exercised on the board.
[1] https://lore.kernel.org/all/20261114-b4-cs75xx-v7-0-8f17f38821b4@xxxxxxxxx/
---
Changes in v4:
- rebase on v7.4-rc1
- split out of "Cortina Systems CS75xx: interrupt controller, GPIO, I2C
and TWD watchdog" so that each driver can go through its own tree; no
longer based on the platform series
- binding: limit clock-frequency to 400 kHz instead of listing 100 and
400 kHz, which is what the driver accepts; I kept Rob's Reviewed-by
from v3 for this one-line change
- collect Reviewed-by tags
- use fsleep() and device_set_node(); sort the Kconfig and Makefile
entries
- Link to v3: https://patch.msgid.link/20261013-b4-cs75xx-s2-v3-0-181bb0d23f4c@xxxxxxxxx
Changes in v3:
- rebase on v6 of the platform series
- reset the controller with its interrupt disabled, check the prescaler
against the field width exactly, wait for a bus held by another master
up to the adapter timeout (sashiko-bot)
- Link to v2: https://patch.msgid.link/20261013-b4-cs75xx-s2-v2-0-94f8c0a90cda@xxxxxxxxx
Changes in v2:
- rebase on v5 of the platform series
- do not include <linux/mod_devicetable.h> (Uwe)
- complete a failed transfer only once its stop condition is done, so
that the stop interrupt cannot race with the next transfer; take the
lock over the whole interrupt handler; report a NACK of the last byte
of a write; enable the interrupt again after a reset on timeout; fail
with -EBUSY when the bus stays busy (sashiko-bot)
- Link to v1: https://patch.msgid.link/20261012-b4-cs75xx-s2-v1-0-8a7641b7b79c@xxxxxxxxx
To: Andi Shyti <andi.shyti@xxxxxxxxxx>
To: Rob Herring <robh@xxxxxxxxxx>
To: Krzysztof Kozlowski <krzk+dt@xxxxxxxxxx>
To: Conor Dooley <conor+dt@xxxxxxxxxx>
Cc: linux-i2c@xxxxxxxxxxxxxxx
Cc: devicetree@xxxxxxxxxxxxxxx
Cc: linux-kernel@xxxxxxxxxxxxxxx
Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
---
Fil Dunsky (2):
dt-bindings: i2c: Add Cortina Systems CS7542 I2C controller
i2c: Add Cortina Systems CS75xx I2C controller driver
.../bindings/i2c/cortina,cs7542-i2c.yaml | 56 +++
drivers/i2c/busses/Kconfig | 11 +
drivers/i2c/busses/Makefile | 1 +
drivers/i2c/busses/i2c-cs75xx.c | 392 +++++++++++++++++++++
4 files changed, 460 insertions(+)
---
base-commit: 6628e7d4c6b25c8d18f1345e3a20d21829aae7e4
change-id: 20261015-cs75xx-i2c-944d27231b4c
Best regards,
--
Fil Dunsky <filipp.dunsky@xxxxxxxxx>