Re: [PATCH v3 0/2] arm64: dts: allwinner: Support Orange Pi 3 LTS
From: Cristian Filipescu
Date: Sun Nov 15 2026 - 18:44:28 EST
Hi Chen-Yu,
On Sun, Nov 15, 2026 at 3:00 AM Chen-Yu Tsai <wens@xxxxxxxxxx> wrote:
>
> On Tue, Oct 27, 2026 at 7:34 AM Cristian Filipescu via B4 Relay
> <devnull+filipescu.cristian.gmail.com@xxxxxxxxxx> wrote:
> >
> > Continue Jernej Skrabec's April 2025 series, adding the board compatible
> > and device tree for the Allwinner H6-based Orange Pi 3 LTS.
> >
> > Board testing passed SD/eMMC reads, both LEDs at drive strength 10,
> > and five Ethernet interface cycles plus three MAC driver rebinds.
> > Each network cycle reached 1 Gbps/full duplex, obtained DHCP and passed
> > ping; PHY ID and 125 MHz clock-output configuration were read back.
> > eMMC DDR52 at 50 MHz and HS200 at 150 MHz each passed 768 MiB of direct
> > reads and 256 MiB of patterned writes with verified readbacks and data
> > restoration. All reported MMC error counters were zero. Both board DTBs
> > compile and pass schema checks.
> >
> > Codex assisted with DTS updates, review analysis and build checks;
> > Cristian performed the board tests.
> >
> > ---
> > Changes in v3:
> > - Keep green as power and red as status, matching Armbian LTS roles;
> > default green on and red off without a boot-stage sequence.
>
> The roles should match the schematics, as the hardware vendor specified.
Agreed. v4 now inherits red PL4 as power/on and green PL7 as
status/off from sun50i-h6-orangepi.dtsi, matching the schematic. I have
removed the Armbian-based rationale from the current revision description.
>
> > - Select drive strength 10 on PL4 and PL7 with per-LED pinctrl states.
> > - Move PHY reset to the MDIO bus, before discovery and outside detach.
> > - Specify the YT8531C PHY ID; MAC rebind fails with early autodetection.
>
> Why do you need the PHY ID if you moved the PHY reset up to the bus level
>
> ChenYu
I have dropped the explicit PHY ID in v4. Generic discovery now
passes five interface cycles and three MAC unbind/rebind cycles, both with
and without temporary PHY-ID logging. Each run reached 1 Gbps/full duplex,
obtained DHCP in all eight cycles and passed 24/24 pings. The initial ID
reads matched 4f51:e91b, and the configured 125 MHz output was retained.
>
> > - Enable 1.8 V eMMC DDR52 and HS200 after board testing; retain the
> > existing H6 maximum frequency of 150 MHz.
> > - Shorten the descriptions and update validation status.
> > - Link to v2: https://lore.kernel.org/all/20261022-sunxi-orangepi-3-lts-v2-0-70b899252c6a@xxxxxxxxx/
> >
> > ---
> > Jernej Skrabec (2):
> > dt-bindings: arm: sunxi: Add Orange Pi 3 LTS board
> > arm64: dts: allwinner: h6: Add Orange Pi 3 LTS
> >
> > Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +
> > arch/arm64/boot/dts/allwinner/Makefile | 1 +
> > .../dts/allwinner/sun50i-h6-orangepi-3-lts.dts | 379 +++++++++++++++++++++
> > 3 files changed, 385 insertions(+)
> > ---
> > base-commit: 4403278e4ea2f654f8130a5c03eb8b4516a0f201
> > change-id: 20261022-sunxi-orangepi-3-lts-43b92246a8ed
> >
> > Best regards,
> > --
> > Cristian Filipescu <filipescu.cristian@xxxxxxxxx>
> >
> >
Regards,
Cristian Filipescu
------------------------------------