Re: [PATCH net-next v21 06/13] ax88179_178a: Add EEE configuration support for AX88179A PHYs
From: netdev-bot+sashiko
Date: Sun Nov 15 2026 - 21:07:43 EST
Thank you for your contribution! Sashiko AI review found 2 potential
issue(s) to consider.
Critical: 0 · High: 0 · Medium: 1 · Low: 1
If you believe none of the issues are legitimate, please reply to each
issue of Medium severity or higher and explain why the AI is wrong.
If any of them are legitimate and you plan to respin, please let patchwork
know by including "pw-bot: cr" as a separate line at the end of your reply
(one such reply per series is enough).
- [Medium] This patch fills phylink_config.lpi_interfaces in
ax88179a_phylink_setup() (drivers/net/usb/ax88179a_devices.c:470-472).
- [Low] Once this patch fills lpi_interfaces, pl->mac_supports_eee
becomes true, and the new .get_eee/.set_eee ops…
--
ax88179_178a: Add EEE configuration support for AX88179A PHYs
This commit fills phylink_config.lpi_interfaces in ax88179a_phylink_setup(),
so phylink now treats the MAC as EEE capable. It also adds ethtool
get_eee/set_eee operations that call into phylink.
> diff --git a/drivers/net/usb/ax88179a_devices.c b/drivers/net/usb/ax88179a_devices.c
> index 62619fd68c408..272e923656832 100644
> --- a/drivers/net/usb/ax88179a_devices.c
> +++ b/drivers/net/usb/ax88179a_devices.c
> @@ -225,6 +225,20 @@ static int ax88179a_get_eeprom_len(struct net_device *net)
> return AX88179A_EEPROM_LEN;
> }
>
> +static int ax88179a_get_eee(struct net_device *net, struct ethtool_keee *edata)
> +{
> + struct ax88179_data *ax179_data = netdev2data(net);
> +
> + return phylink_ethtool_get_eee(ax179_data->phylink, edata);
> +}
> +
> +static int ax88179a_set_eee(struct net_device *net, struct ethtool_keee *edata)
> +{
> + struct ax88179_data *ax179_data = netdev2data(net);
> +
> + return phylink_ethtool_set_eee(ax179_data->phylink, edata);
> +}
[Severity: Low]
Will ethtool now accept and report a tx_lpi_timer that the hardware never
uses?
ax88179a_mac_enable_tx_lpi() ignores its timer argument:
static int ax88179a_mac_enable_tx_lpi(struct phylink_config *config, u32 timer, bool tx_clk_stop)
{
...
/* AX88179A does not provide LPI timer registers */
return ax88179_write_cmd(dev, AX_GPHY_CTL, AX_GPHY_EEE_CTRL, true, 0, NULL);
}
phylink_ethtool_set_eee() does not check eee->tx_lpi_timer. On success it
stores the value in pl->eee_cfg, and later get_eee calls report it back.
So "ethtool --set-eee <dev> tx-timer N" succeeds and reads back N, but the
hardware does not change.
ax88179a_phylink_setup() also never sets phylink_config.lpi_timer_default,
so phylink_create() starts with:
pl->eee_cfg.tx_lpi_timer = pl->config->lpi_timer_default;
As a result, ethtool shows a 0 us LPI timer by default. That probably does
not match the fixed delay the hardware actually uses.
Before this patch, get/set_eee returned -EOPNOTSUPP, so none of this was
reachable. Some other phylink drivers (r8169, ksz, rtl8365mb) also ignore
the timer.
Could lpi_timer_default be set to the hardware's real fixed delay, or could
values other than the default be rejected?
[ ... ]
> @@ -451,6 +467,10 @@ static int ax88179a_phylink_setup(struct usbnet *dev)
> phy_if_mode = PHY_INTERFACE_MODE_SGMII;
> }
>
> + memcpy(data->phylink_config.lpi_interfaces,
> + data->phylink_config.supported_interfaces,
> + sizeof(data->phylink_config.lpi_interfaces));
> +
[Severity: Medium]
Does this change the default EEE advertisement on chips other than the
AX88772D?
With lpi_interfaces filled in, phylink_create() now sets
pl->mac_supports_eee to true. ax88179a_phylink_setup() still sets
eee_enabled_default = false, so pl->eee_cfg.eee_enabled is false. In
phylink_bringup_phy() this means:
if (pl->mac_supports_eee) {
if (pl->eee_cfg.eee_enabled)
phy_support_eee(phy);
...
linkmode_and(phy->advertising_eee, phy->advertising_eee,
pl->supported_lpi);
} else if (pl->mac_supports_eee_ops) {
/* MAC supports phylink EEE, but wants EEE always disabled. */
phy_disable_eee(phy);
}
Before this patch, the else-if branch ran and phy_disable_eee() cleared
advertising_eee. Now only the linkmode_and() runs. Whatever phy_probe()
read from the PHY's power-on EEE advertisement stays in place, and
phy_probe() has already set:
phydev->eee_cfg.eee_enabled = !linkmode_empty(phydev->advertising_eee);
If the internal PHY advertises EEE at reset, the link would negotiate EEE
with the partner by default, and ethtool --show-eee would report EEE as
enabled. Meanwhile, phylink's eee_cfg says disabled and MAC TX LPI stays off.
This seems to go against the comment in ax88179a_reset():
/* Ensure EEE state is off, consistent with phylink setup */
ax88179_write_cmd(dev, AX_GPHY_CTL, AX_GPHY_EEE_CTRL, false, 0, NULL);
After this patch, that comment holds for the MAC LPI control but not for the
PHY advertisement. The older ax88179_178a driver for the same devices
cleared the advertisement explicitly in ax88179_reset(), using
ax88179_disable_eee() and linkmode_zero(eee_data.advertised).
If EEE is meant to be off by default, should the PHY's EEE advertisement be
cleared explicitly? That way the default would not depend on the PHY's reset
or strap values.
--
Sashiko AI review · https://netdev-ai.bots.linux.dev/sashiko/#/patchset/20261114-ax88179a-v21-0-c2d34410bcbe%40birger-koblitz.de