Re: [PATCH net-next v3 3/5] selftests: seg6: move SRv6 End PSP setup into its own helper

From: Hangbin Liu

Date: Mon Nov 16 2026 - 01:21:15 EST


Hi Andrea,
On Mon, Nov 16, 2026 at 05:26:59AM +0100, Andrea Mayer wrote:
> > [snip]
> > diff --git a/tools/testing/selftests/net/srv6_end_flavors_test.sh b/tools/testing/selftests/net/srv6_end_flavors_test.sh
> > index 157baa8ecb0b..0ed5bfe99029 100755
> > --- a/tools/testing/selftests/net/srv6_end_flavors_test.sh
> > +++ b/tools/testing/selftests/net/srv6_end_flavors_test.sh
> > @@ -488,8 +488,9 @@ cleanup()
> >
> > # check whether the setup phase was completed successfully or not. In
> > # case of an error during the setup phase of the testing environment,
> > - # the selftest is considered as "skipped".
> > - if [ "${SETUP_ERR}" -ne 0 ]; then
> > + # the selftest is considered as "skipped", unless a test has already
> > + # recorded a failure.
> > + if [ "${SETUP_ERR}" -ne 0 ] && [ "$ret" -ne "$ksft_fail" ]; then
> > echo "SKIP: Setting up the testing environment failed"
> > exit "${ksft_skip}"
> > fi
>
> When a test has already failed and the setup then fails, the script
> exits with 1 and does not say that the setup failed. For example, with
> hs-2 -> gw failing and then an error in setup_end_flv_psp(), the last
> TEST lines in the log are:
>
> TEST: IPv6 Hosts connectivity: hs-1 -> gw [ OK ]
> TEST: IPv6 Hosts connectivity: hs-2 -> gw [FAIL]
>
> The End PSP tests did not run. Before this patch, the setup ran before
> any test, and cleanup() printed "Setting up the testing environment
> failed" on every setup error. Could cleanup() print it also in this
> case, keeping the exit code 1? Something like:
>
> if [ "${SETUP_ERR}" -ne 0 ]; then
> if [ "${ret}" -ne "${ksft_fail}" ]; then
> echo "SKIP: Setting up the testing environment failed"
> exit "${ksft_skip}"
> fi
>
> echo "FAIL: Setting up the testing environment failed"
> fi
>
> exit "${ret}"

OK, I will fix it.

> > # see __setup_rt_policy
> > @@ -962,17 +980,29 @@ setup()
> > setup_hs 1 1
> > setup_hs 2 2
> >
> > - # set up the loopback addresses of the hosts used by the Policies (i.c)
> > - # and (i.d).
> > - setup_hs_lo_addr 1 1 "${END_CSID_PSP_FUNC}"
> > - setup_hs_lo_addr 2 2 "${END_CSID_PSP_FUNC}"
> > -
> > # set up default SRv6 Endpoints (i.e. SRv6 End behavior)
> > setup_rt_local_sids 1 "2 3 4"
> > setup_rt_local_sids 2 "1 3 4"
> > setup_rt_local_sids 3 "1 2 4"
> > setup_rt_local_sids 4 "1 2 3"
> >
> > + # testing environment was set up successfully
> > + SETUP_ERR=0
> > +}
> > +
> > +setup_end_flv_psp()
> > +{
> > + SETUP_ERR=1
> > +
> > + # set up the loopback addresses of the hosts used by the Policies (i.c)
> > + # and (i.d).
> > + setup_hs_lo_addr 1 1 "${END_CSID_PSP_FUNC}"
> > + setup_hs_lo_addr 2 2 "${END_CSID_PSP_FUNC}"
> > +
> > + # setup proxy on route entries for hosts
> > + setup_rt_host_proxy 1 2 "${END_CSID_PSP_FUNC}"
> > + setup_rt_host_proxy 2 1 "${END_CSID_PSP_FUNC}"
> > +
> > # set up SRv6 policies
> > # create a connection between hosts hs-1 and hs-2.
> > # The path between hs-1 and hs-2 traverses SRv6 aware routers.
>
> Before this patch, __setup_rt_policy() added the proxy entry together
> with the route of each Policy. With this patch, each scenario calls
> setup_rt_host_proxy() instead.
>
> In this v3, 4/5 deletes the proxies when the scenario ends, like the
> routes of the Policies. So I think the proxy entry can stay in
> __setup_rt_policy(), and in 4/5 its defer can go next to the defer of
> the route. What do you think?

OK, I will keep the proxy set up in __setup_rt_policy.

Thanks
Hangbin