[PATCH net v3 09/10] net: au1000: keep the MAC stopped until the PHY link is ready

From: Florian Fainelli

Date: Tue Nov 17 2026 - 14:33:59 EST


phy_stop() powers down the PHY when the interface is closed. The driver
leaves MAC receive/transmit enabled on link-down and enables them during
initialization before the PHY resumes. MTX-1 can hang when the MAC runs
while its MII clocks are absent or still recovering.

Stop the MAC on link-down before phylib suspends the PHY. On open, clear
the driver's acknowledged link cache and synchronously resume the PHY
to restore its MII clocks and honor its recovery delay before MAC
initialization. Preserve the existing au1000_init() before phy_start()
ordering so the PHY worker cannot access MDIO or enable traffic during
setup. Leave RX/TX stopped until a link-up callback configures duplex
and enables traffic.

Use the acknowledged link and duplex cache under the device lock during
initialization, retaining it for watchdog recovery. Keep the reset-time
hard stop for paths without a preceding link-down callback. On resume
failure reset the MAC and release the IRQ. Remove the unreachable
initialization-error branch, since au1000_init() always returns zero.
Reconcile the initialization and probe comments: initialization forces
a reset itself, and PHY resume may already have enabled the MAC for
MDIO accesses.

Fixes: be9dad1f9f26 ("net: phy: suspend phydev when going to HALTED")
Signed-off-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
---
drivers/net/ethernet/amd/au1000_eth.c | 49 ++++++++++++++++++---------
1 file changed, 33 insertions(+), 16 deletions(-)

diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index cb2f3333ba9f..98a75aba92e1 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -456,7 +456,8 @@ au1000_adjust_link(struct net_device *dev)
/* link state changed */

if (!phydev->link) {
- /* link went down */
+ /* Stop the MAC before the PHY can remove its clocks. */
+ au1000_hard_stop(dev);
aup->old_speed = 0;
aup->old_duplex = -1;
}
@@ -688,13 +689,11 @@ static const struct ethtool_ops au1000_ethtool_ops = {
static u32 au1000_rx_mode(struct net_device *dev, u32 reg);

/*
- * Initialize the interface.
+ * Reset and initialize the interface.
*
- * When the device powers up, the clocks are disabled and the
- * mac is in reset state. When the interface is closed, we
- * do the same -- reset the device and disable the clocks to
- * conserve power. Thus, whenever au1000_init() is called,
- * the device should already be in reset state.
+ * The PHY must be resumed before initializing the MAC. MDIO accesses
+ * during PHY resume may have already enabled the MAC clocks and released
+ * reset; au1000_enable_mac(dev, 1) forces a reset regardless of that state.
*/
static int au1000_init(struct net_device *dev)
{
@@ -729,12 +728,12 @@ static int au1000_init(struct net_device *dev)

wmb(); /* drain writebuffer */

- control = MAC_RX_ENABLE | MAC_TX_ENABLE;
+ control = 0;
#ifndef CONFIG_CPU_LITTLE_ENDIAN
control |= MAC_BIG_ENDIAN;
#endif
if (dev->phydev) {
- if (dev->phydev->link && (DUPLEX_FULL == dev->phydev->duplex))
+ if (aup->old_link && aup->old_duplex == DUPLEX_FULL)
control |= MAC_FULL_DUPLEX;
else
control |= MAC_DISABLE_RX_OWN;
@@ -744,6 +743,10 @@ static int au1000_init(struct net_device *dev)

control = au1000_rx_mode(dev, control);

+ /* Only use link state acknowledged by au1000_adjust_link(). */
+ if (!dev->phydev || aup->old_link)
+ control |= MAC_RX_ENABLE | MAC_TX_ENABLE;
+
writel(control, &aup->mac->control);
writel(0x8100, &aup->mac->vlan1_tag); /* activate vlan support */
wmb(); /* drain writebuffer */
@@ -918,6 +921,7 @@ static irqreturn_t au1000_interrupt(int irq, void *dev_id)

static int au1000_open(struct net_device *dev)
{
+ unsigned long flags;
int retval;
struct au1000_private *aup = netdev_priv(dev);

@@ -930,13 +934,21 @@ static int au1000_open(struct net_device *dev)
return retval;
}

- retval = au1000_init(dev);
- if (retval) {
- netdev_err(dev, "error in au1000_init\n");
- free_irq(dev->irq, dev);
- return retval;
+ spin_lock_irqsave(&aup->lock, flags);
+ aup->old_link = 0;
+ aup->old_speed = 0;
+ aup->old_duplex = -1;
+ spin_unlock_irqrestore(&aup->lock, flags);
+
+ /* Restore the MII clocks without starting the PHY state machine. */
+ if (dev->phydev) {
+ retval = phy_resume(dev->phydev);
+ if (retval)
+ goto err_reset;
}

+ au1000_init(dev);
+
if (dev->phydev)
phy_start(dev->phydev);

@@ -945,6 +957,11 @@ static int au1000_open(struct net_device *dev)
netif_dbg(aup, drv, dev, "open: Initialization done.\n");

return 0;
+
+err_reset:
+ au1000_reset_mac(dev);
+ free_irq(dev->irq, dev);
+ return retval;
}

static int au1000_close(struct net_device *dev)
@@ -1306,8 +1323,8 @@ static int au1000_probe(struct platform_device *pdev)
dev->watchdog_timeo = ETH_TX_TIMEOUT;

/*
- * The boot code uses the ethernet controller, so reset it to start
- * fresh. au1000_init() expects that the device is in reset state.
+ * The boot code uses the ethernet controller, so stop it and gate
+ * its clock until the driver needs it.
*/
au1000_reset_mac(dev);

--
2.53.0