[PATCH v2 5/6] arm64: dts: allwinner: a133: Add CPU OPP table

From: Rajan Yadav via B4 Relay

Date: Wed Nov 18 2026 - 05:52:49 EST


From: Rajan Yadav <rajanyadav0307@xxxxxxxxx>

Add the A133 CPU OPPs from the vendor BSP (sun50iw10p1.dtsi), plus
1608 MHz for b0 and b1 from the vendor table in the factory firmware of
the KickPi K5C. There are ten voltage sets, speed0-5 for the a0-a5/a6
grades and speed6-9 for the "high speed" b0-b3 grades.
opp-supported-hw selects the frequencies of each grade:

- 1464 MHz only for the a grades
- 1416 and 1512 MHz only for the b grades
- 1608 MHz only for b0 and b1, the revision A-E "high speed" grades
- 408-1320 MHz for all

The highest voltage is 1.18 V, inside the 0.81-1.2 V recommended
operating range of VDD_CPU in the A133 datasheet (V1.5, table 5-2).

The BSP uses 1008 MHz where the A100 table uses 1080 MHz, at the same
voltages for a0-a2. U-Boot starts the CPU at 1008 MHz, which mainline
now reports as an unlisted initial frequency. This table follows the
BSP.

The BSP table stops at 1512 MHz, although some datasheet versions list
1.6 GHz for the A133. The factory firmware of the KickPi K5C (Linux
4.9.170, built January 2026) has the same table plus five OPPs:
1608 MHz for b0 (1.18 V) and b1 (1.13 V, at most 1.14 V), and 1416 MHz
for a0-a2. This patch takes the 1608 MHz OPP from it.

The K5C is a b2 part and never uses this OPP. With a test-only change
that forces the grade, the CPU PLL locked at 1608 MHz and the PMIC was
set to 1.18 V for b0 and 1.13 V for b1. Forced to b0, two 20-minute
runs of full load on the K5C without a heatsink reached the 90 C
passive trip after 10-13 minutes; from then on the temperature stayed
between 83.5 and 90.4 C.

The table has the A100 compatible as a fallback and the speed bin cell
first, so a kernel without A133 support selects speed0-2 from the speed
bin and gets the voltages of the A100 table, with 1008 instead of
1080 MHz. It needs the efuse cells added to sun50i-a100.dtsi in the
previous patch.

A script compared every voltage and the frequency set of every grade
with both vendor tables. It found no difference to the BSP file other
than the added 1608 MHz OPP, and no difference to the factory table
other than its 1416 MHz OPP for a0-a2.

Claude Code (Anthropic) drafted this table and its message from the
two vendor device trees (numbers only) and wrote the comparison script;
I reviewed it and tested it on a KickPi K5C.

Suggested-by: Andre Przywara <andre.przywara@xxxxxxx>
Signed-off-by: Rajan Yadav <rajanyadav0307@xxxxxxxxx>

---
Changes in v2:
- Add 1608 MHz for b0 and b1 from the factory firmware table, as Andre
asked; the commit message describes the source and the K5C tests.
- Alexander's Reviewed-by and Tested-by for v1 are not carried over
because of this change. Alexander, could you check whether they
still apply to this version?
---
.../boot/dts/allwinner/sun50i-a133-cpu-opp.dtsi | 182 +++++++++++++++++++++
1 file changed, 182 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a133-cpu-opp.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a133-cpu-opp.dtsi
new file mode 100644
index 00000000000..dd5fdeea7ea
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a133-cpu-opp.dtsi
@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2026 Rajan Yadav <rajanyadav0307@xxxxxxxxx>
+/*
+ * A133 CPU OPPs. The voltages and grade selection follow the Allwinner
+ * vendor BSP (sun50iw10p1.dtsi); 1608 MHz for b0 and b1 is from the vendor
+ * table in the factory firmware of the KickPi K5C. Index 0-5 are the
+ * vendor's a0-a5 grades (a6 uses the a5 values), index 6-9 are the "high
+ * speed" b0-b3 grades. This needs the efuse cells from sun50i-a100.dtsi.
+ */
+
+/ {
+ cpu_opp_table: opp-table-cpu {
+ compatible = "allwinner,sun50i-a133-operating-points",
+ "allwinner,sun50i-a100-operating-points";
+ nvmem-cells = <&cpu_speed_grade>, <&chip_marking>,
+ <&cpu_pcpu>, <&cpu_bin_ext>;
+ nvmem-cell-names = "bin", "marking", "pcpu", "bin-ext";
+ opp-shared;
+
+ opp-408000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <408000000>;
+
+ opp-microvolt-speed0 = <900000>;
+ opp-microvolt-speed1 = <900000>;
+ opp-microvolt-speed2 = <900000>;
+ opp-microvolt-speed3 = <940000>;
+ opp-microvolt-speed4 = <940000>;
+ opp-microvolt-speed5 = <920000>;
+ opp-microvolt-speed6 = <900000>;
+ opp-microvolt-speed7 = <900000>;
+ opp-microvolt-speed8 = <940000>;
+ opp-microvolt-speed9 = <920000>;
+ opp-supported-hw = <0x3ff>;
+ };
+
+ opp-600000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <600000000>;
+
+ opp-microvolt-speed0 = <900000>;
+ opp-microvolt-speed1 = <900000>;
+ opp-microvolt-speed2 = <900000>;
+ opp-microvolt-speed3 = <940000>;
+ opp-microvolt-speed4 = <940000>;
+ opp-microvolt-speed5 = <920000>;
+ opp-microvolt-speed6 = <900000>;
+ opp-microvolt-speed7 = <900000>;
+ opp-microvolt-speed8 = <940000>;
+ opp-microvolt-speed9 = <920000>;
+ opp-supported-hw = <0x3ff>;
+ };
+
+ opp-816000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <816000000>;
+
+ opp-microvolt-speed0 = <940000>;
+ opp-microvolt-speed1 = <900000>;
+ opp-microvolt-speed2 = <900000>;
+ opp-microvolt-speed3 = <940000>;
+ opp-microvolt-speed4 = <940000>;
+ opp-microvolt-speed5 = <920000>;
+ opp-microvolt-speed6 = <900000>;
+ opp-microvolt-speed7 = <900000>;
+ opp-microvolt-speed8 = <940000>;
+ opp-microvolt-speed9 = <920000>;
+ opp-supported-hw = <0x3ff>;
+ };
+
+ opp-1008000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <1008000000>;
+
+ opp-microvolt-speed0 = <1020000>;
+ opp-microvolt-speed1 = <980000>;
+ opp-microvolt-speed2 = <950000>;
+ opp-microvolt-speed3 = <1020000>;
+ opp-microvolt-speed4 = <960000>;
+ opp-microvolt-speed5 = <940000>;
+ opp-microvolt-speed6 = <980000>;
+ opp-microvolt-speed7 = <950000>;
+ opp-microvolt-speed8 = <960000>;
+ opp-microvolt-speed9 = <940000>;
+ opp-supported-hw = <0x3ff>;
+ };
+
+ opp-1200000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <1200000000>;
+
+ opp-microvolt-speed0 = <1100000>;
+ opp-microvolt-speed1 = <1020000>;
+ opp-microvolt-speed2 = <1000000>;
+ opp-microvolt-speed3 = <1100000>;
+ opp-microvolt-speed4 = <980000>;
+ opp-microvolt-speed5 = <960000>;
+ opp-microvolt-speed6 = <1020000>;
+ opp-microvolt-speed7 = <1000000>;
+ opp-microvolt-speed8 = <980000>;
+ opp-microvolt-speed9 = <960000>;
+ opp-supported-hw = <0x3ff>;
+ };
+
+ opp-1320000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <1320000000>;
+
+ opp-microvolt-speed0 = <1160000>;
+ opp-microvolt-speed1 = <1060000>;
+ opp-microvolt-speed2 = <1030000>;
+ opp-microvolt-speed3 = <1160000>;
+ opp-microvolt-speed4 = <1020000>;
+ opp-microvolt-speed5 = <1000000>;
+ opp-microvolt-speed6 = <1060000>;
+ opp-microvolt-speed7 = <1030000>;
+ opp-microvolt-speed8 = <1020000>;
+ opp-microvolt-speed9 = <1000000>;
+ opp-supported-hw = <0x3ff>;
+ };
+
+ opp-1416000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <1416000000>;
+
+ opp-microvolt-speed6 = <1100000>;
+ opp-microvolt-speed7 = <1070000>;
+ opp-microvolt-speed8 = <1060000>;
+ opp-microvolt-speed9 = <1040000>;
+ opp-supported-hw = <0x3c0>;
+ };
+
+ opp-1464000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <1464000000>;
+
+ opp-microvolt-speed0 = <1180000>;
+ opp-microvolt-speed1 = <1180000>;
+ opp-microvolt-speed2 = <1130000>;
+ opp-microvolt-speed3 = <1180000>;
+ opp-microvolt-speed4 = <1100000>;
+ opp-microvolt-speed5 = <1080000>;
+ opp-supported-hw = <0x3f>;
+ };
+
+ opp-1512000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <1512000000>;
+
+ opp-microvolt-speed6 = <1180000>;
+ opp-microvolt-speed7 = <1130000 1130000 1140000>;
+ opp-microvolt-speed8 = <1100000>;
+ opp-microvolt-speed9 = <1080000>;
+ opp-supported-hw = <0x3c0>;
+ };
+
+ opp-1608000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <1608000000>;
+
+ opp-microvolt-speed6 = <1180000>;
+ opp-microvolt-speed7 = <1130000 1130000 1140000>;
+ opp-supported-hw = <0xc0>;
+ };
+ };
+};
+
+&cpu0 {
+ operating-points-v2 = <&cpu_opp_table>;
+};
+
+&cpu1 {
+ operating-points-v2 = <&cpu_opp_table>;
+};
+
+&cpu2 {
+ operating-points-v2 = <&cpu_opp_table>;
+};
+
+&cpu3 {
+ operating-points-v2 = <&cpu_opp_table>;
+};

--
2.34.1