[PATCH net-next v3 0/3] ionic: make the device command timeout configurable

From: Nikhil P. Rao

Date: Wed Nov 18 2026 - 19:33:10 EST


ionic waits a fixed 5 seconds for device and admin queue commands, and
the RDMA driver gives its admin queue 2 seconds. Some commands can take
the firmware longer than that, for example while a PFC configuration
change flaps the links. The firmware is alive but slow, yet the
timed-out command and everything queued behind it fail, and an RDMA
admin queue timeout resets the RDMA LIF so that later verbs fail with
-ENODEV.

Patch 1 makes the timeout a per-device value without changing it.
Patch 2 has the RDMA admin queue use the ionic command timeout instead
of its own 2 seconds.
Patch 3 adds a permanent devlink parameter, cmd_timeout, on each PF.
The firmware stores the value per PF in NVM, and the PF and its VFs
read it at probe and after a reset.

Tested on an AMD Pensando adapter under KASAN and lockdep: get and set
of the parameter, and the stored value read back after an FLR.

Patch 2 conflicts with "RDMA/ionic: Wait the device command timeout for
admin queue commands", sent to rdma for-rc:
https://patch.msgid.link/20261118-b4-ionic-rdma-admin-timeout-v1-1-39536999a3e4@xxxxxxx
When both are merged, keep this series' version: ionic_admin_timeout()
replaces IONIC_ADMIN_TIMEOUT, and already defaults to 5 seconds.

This series was developed with the help of an LLM-based coding
assistant (Claude).

---
Changes in v3:
- patch 3:
- register the parameter once at probe, on PFs only, instead of
unregistering it on firmware and PCI resets and registering it
again on restart
- get reports the value read at the last probe or reset, or stored by
a later set, instead of sending a device command
- keep the timeout in use when reading the stored value fails,
instead of falling back to the default
- read the stored value right after identify at probe and PCI reset,
so the remaining commands there use it
- rebase on net-next
- Link to v2: https://patch.msgid.link/20261105-b4-ionic-cmd-timeout-v2-0-35a9a2aa48b1@xxxxxxx

Changes in v2:
- patch 3:
- comment in ionic_dl_cmd_timeout_get() on why it has no FW_RESET check
- changelog "after probe or reset" -> "after probe or PCI reset"
- Link to v1: https://patch.msgid.link/20261102-b4-ionic-cmd-timeout-v1-0-2f75c2d0a0c7@xxxxxxx

---
Arun Kumar Prakash (3):
ionic: make the command timeout per device
RDMA/ionic: Use the ionic command timeout for the admin queue
ionic: add devlink param for command timeout

Documentation/networking/devlink/ionic.rst | 27 ++++++++
drivers/infiniband/hw/ionic/ionic_admin.c | 9 ++-
drivers/net/ethernet/pensando/ionic/ionic.h | 10 ++-
drivers/net/ethernet/pensando/ionic/ionic_api.h | 8 +++
drivers/net/ethernet/pensando/ionic/ionic_aux.c | 8 ++-
.../net/ethernet/pensando/ionic/ionic_bus_pci.c | 3 +
drivers/net/ethernet/pensando/ionic/ionic_dev.c | 70 ++++++++++++++++++--
drivers/net/ethernet/pensando/ionic/ionic_dev.h | 2 +
.../net/ethernet/pensando/ionic/ionic_devlink.c | 77 ++++++++++++++++++++++
.../net/ethernet/pensando/ionic/ionic_ethtool.c | 12 ++--
drivers/net/ethernet/pensando/ionic/ionic_fw.c | 8 +--
drivers/net/ethernet/pensando/ionic/ionic_if.h | 8 +++
drivers/net/ethernet/pensando/ionic/ionic_lif.c | 11 ++--
drivers/net/ethernet/pensando/ionic/ionic_main.c | 17 ++---
14 files changed, 236 insertions(+), 34 deletions(-)
---
base-commit: 44454974aef9c81949e5858ed3e8cbd08e104cad
change-id: 20261102-b4-ionic-cmd-timeout-c704d5304b4f

Best regards,
--
Nikhil P. Rao <nikhil.rao@xxxxxxx>