[PATCH net-next v4 3/5] selftests: seg6: move SRv6 End PSP setup into its own helper
From: Hangbin Liu
Date: Thu Nov 19 2026 - 08:58:41 EST
From: Hangbin Liu <liuhangbin@xxxxxxxxxx>
setup() installs both the base topology and the End PSP policies. That
couples general test setup with one specific flavor scenario and makes
it hard to add further flavor cases cleanly.
Extract the End PSP policy setup into setup_end_flv_psp() so flavor
tests can set up and later tear down independently (the matching
cleanup arrives in a following patch).
Run the block under set -e so a setup failure is treated as an error
instead of falling through into the connectivity checks. When deciding
to report the run as skipped, keep any failure already recorded by a
test, so a real failure is not converted into a skip.
Signed-off-by: Hangbin Liu <liuhangbin@xxxxxxxxxx>
---
.../testing/selftests/net/srv6_end_flavors_test.sh | 33 ++++++++++++++++------
1 file changed, 25 insertions(+), 8 deletions(-)
diff --git a/tools/testing/selftests/net/srv6_end_flavors_test.sh b/tools/testing/selftests/net/srv6_end_flavors_test.sh
index 157baa8ecb0b..250de54d8bfa 100755
--- a/tools/testing/selftests/net/srv6_end_flavors_test.sh
+++ b/tools/testing/selftests/net/srv6_end_flavors_test.sh
@@ -488,10 +488,15 @@ cleanup()
# check whether the setup phase was completed successfully or not. In
# case of an error during the setup phase of the testing environment,
- # the selftest is considered as "skipped".
+ # the selftest is considered as "skipped", unless a test has already
+ # recorded a failure.
if [ "${SETUP_ERR}" -ne 0 ]; then
- echo "SKIP: Setting up the testing environment failed"
- exit "${ksft_skip}"
+ if [ "$ret" -ne "$ksft_fail" ]; then
+ echo "SKIP: Setting up the testing environment failed"
+ exit "${ksft_skip}"
+ fi
+
+ echo "FAIL: Setting up the testing environment failed"
fi
exit "${ret}"
@@ -962,17 +967,25 @@ setup()
setup_hs 1 1
setup_hs 2 2
- # set up the loopback addresses of the hosts used by the Policies (i.c)
- # and (i.d).
- setup_hs_lo_addr 1 1 "${END_CSID_PSP_FUNC}"
- setup_hs_lo_addr 2 2 "${END_CSID_PSP_FUNC}"
-
# set up default SRv6 Endpoints (i.e. SRv6 End behavior)
setup_rt_local_sids 1 "2 3 4"
setup_rt_local_sids 2 "1 3 4"
setup_rt_local_sids 3 "1 2 4"
setup_rt_local_sids 4 "1 2 3"
+ # testing environment was set up successfully
+ SETUP_ERR=0
+}
+
+setup_end_flv_psp()
+{
+ SETUP_ERR=1
+
+ # set up the loopback addresses of the hosts used by the Policies (i.c)
+ # and (i.d).
+ setup_hs_lo_addr 1 1 "${END_CSID_PSP_FUNC}"
+ setup_hs_lo_addr 2 2 "${END_CSID_PSP_FUNC}"
+
# set up SRv6 policies
# create a connection between hosts hs-1 and hs-2.
# The path between hs-1 and hs-2 traverses SRv6 aware routers.
@@ -1429,6 +1442,10 @@ set +e
router_tests
host2gateway_tests
+
+set -e
+setup_end_flv_psp
+set +e
host_srv6_end_flv_psp_tests
host_srv6_end_flv_next_csid_psp_tests
host_srv6_end_flv_consumed_srh_tests
--
2.56.0