Re: [PATCH v2 2/6] remoteproc: amd_mbv_bram: Restore reset GPIO direction after PL reconfig
From: Mathieu Poirier
Date: Thu Nov 19 2026 - 11:45:07 EST
On Wed, Nov 04, 2026 at 09:18:58PM -0800, Ben Levinsky wrote:
> Partial reconfiguration of the programmable logic restores the AXI GPIO
> that drives the soft-core reset to its hardware default direction, but
> gpiolib keeps its cached output direction. gpiod_set_value_cansleep()
> then only updates the data register, so the processor never sees a
> reset transition: remoteproc reports it as running while the newly
> loaded firmware never starts.
>
Where does the "partial reconfiguration of the programmable logic" happens?
What makes it partial? Shouldn't that be fixed instead?
> Use gpiod_direction_output() for every reset transition so the output
> direction is re-established, and assert reset briefly before releasing
> it so each start produces a clean reset pulse after the firmware has
> been loaded.
>
> Fixes: f87b4998994e ("remoteproc: Add AMD MicroBlaze/V BRAM-based remote processor driver")
> Assisted-by: Claude:claude-opus-5.5
> Signed-off-by: Ben Levinsky <ben.levinsky@xxxxxxx>
> ---
> drivers/remoteproc/amd_mbv_bram_rproc.c | 23 ++++++++++++++++++++---
> 1 file changed, 20 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/remoteproc/amd_mbv_bram_rproc.c b/drivers/remoteproc/amd_mbv_bram_rproc.c
> index 6cf33c7b7e64..da621f62f7df 100644
> --- a/drivers/remoteproc/amd_mbv_bram_rproc.c
> +++ b/drivers/remoteproc/amd_mbv_bram_rproc.c
> @@ -16,6 +16,7 @@
> */
>
> #include <linux/clk.h>
> +#include <linux/delay.h>
> #include <linux/dma-mapping.h>
> #include <linux/gpio/consumer.h>
> #include <linux/module.h>
> @@ -94,8 +95,24 @@ static int amd_bram_rproc_start(struct rproc *rproc)
> return ret;
> }
>
> + /*
> + * Partial reconfiguration restores the PL GPIO hardware defaults but
> + * leaves gpiolib's cached direction unchanged. Re-establish the output
> + * direction and generate a reset pulse after firmware has been loaded.
> + * gpiod_set_value_cansleep() is insufficient here because it changes the
> + * value without restoring an output direction lost during DFX.
> + */
> + ret = gpiod_direction_output(priv->reset, 1);
> + if (ret) {
> + dev_err(priv->dev, "failed to assert reset: %d\n", ret);
> + clk_disable_unprepare(priv->clk);
> + return ret;
> + }
Why is this needed now rather than when this driver was introduced?
> + /* Hold reset asserted long enough to provide a clean reset pulse. */
> + usleep_range(10, 20);
> +
I really don't like random wait times, please find another way like polling the
GPIO line for an expected value. I also thougth the GPIO subsystem was already
dealing with de-bouncing. And the question from above still stands, i.e what
changed to required sleeping that wasn't there when this driver was first
submitted?
> /* Deassert reset and let the processor run. */
> - ret = gpiod_set_value_cansleep(priv->reset, 0);
> + ret = gpiod_direction_output(priv->reset, 0);
> if (ret) {
> dev_err(priv->dev, "failed to deassert reset: %d\n", ret);
> clk_disable_unprepare(priv->clk);
> @@ -110,8 +127,8 @@ static int amd_bram_rproc_stop(struct rproc *rproc)
> struct amd_bram_rproc *priv = rproc->priv;
> int ret;
>
> - /* Assert reset before disabling the processor clock. */
> - ret = gpiod_set_value_cansleep(priv->reset, 1);
> + /* Restore the output direction after DFX and assert reset. */
> + ret = gpiod_direction_output(priv->reset, 1);
> if (ret) {
> dev_err(priv->dev, "failed to assert reset: %d\n", ret);
> return ret;
> --
> 2.34.1
>