[PATCH net v4 08/10] net: phy: smsc: wait for LAN83C183 power-down recovery

From: Florian Fainelli

Date: Fri Nov 20 2026 - 19:49:07 EST


The LAN83C183 uses the generic PHY driver, which returns immediately
after clearing BMCR_PDOWN. Section 1.11 of the datasheet allows 500 ms
before normal operation is restored. Starting the Au1000 MAC before the
MII clocks recover can hang the MTX-1 when reopening its interface.

Add a LAN83C183 driver entry and resume callback. Wait for recovery only
when BMCR_PDOWN was actually cleared, and propagate MDIO errors without
waiting. Resuming an already awake PHY does not incur the delay.

This supplies the PHY recovery delay; it does not by itself fix the
Au1000 MAC/PHY ordering on reopen. The companion patch, "net: au1000:
keep the MAC stopped until the PHY link is ready", resumes the PHY
synchronously before MAC initialization and stops the MAC before PHY
suspend. Both changes are needed to address the MTX-1 reopen hang.
Keep this PHY change first so the recovery delay is available when the
MAC sequencing fix is applied.

The specific PHY driver must be bound before the MAC attaches the PHY.
For a built-in au1000 MAC used during early boot, enable CONFIG_SMSC_PHY=y.
Module configurations must arrange for smsc.ko to be loaded before PHY
attachment. If attachment falls back to genphy, loading smsc.ko later
does not replace that binding and the recovery delay will not run.
MTX-1 validation used CONFIG_MIPS_AU1X00_ENET=y and CONFIG_SMSC_PHY=y;
the boot logs confirmed attachment to the SMSC LAN83C183 driver.

The LAN83C183 and LSI L80227 document the same LSI/SEEQ OUI and model 4,
so this ID match also binds the L80227 and applies the same conservative
500 ms delay when clearing power-down. The entry otherwise uses generic
PHY helpers and does not program SMSC-specific registers. Hardware
validation is limited to the LAN83C183; the L80227 was not tested.

Sashiko AI review identified the dependency, binding prerequisite and
shared PHY ID.

Fixes: be9dad1f9f26 ("net: phy: suspend phydev when going to HALTED")
Link: https://pdf.dzsc.com/LAN/LAN83C183.pdf#page=44
Link: https://datasheet.octopart.com/L80223-LSI-datasheet-11757091.pdf#page=73
Signed-off-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
---
drivers/net/phy/Kconfig | 2 +-
drivers/net/phy/smsc.c | 27 +++++++++++++++++++++++++++
2 files changed, 28 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 30e9d22c8d1a..10466b2574eb 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -421,7 +421,7 @@ config SMSC_PHY
tristate "SMSC PHYs"
select CRC16
help
- Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs
+ Currently supports the LAN83C183, LAN83C185, LAN8187 and LAN8700 PHYs

config STE10XP
tristate "STMicroelectronics STe10Xp PHYs"
diff --git a/drivers/net/phy/smsc.c b/drivers/net/phy/smsc.c
index 48487149c225..c0713017e54b 100644
--- a/drivers/net/phy/smsc.c
+++ b/drivers/net/phy/smsc.c
@@ -13,6 +13,7 @@
*/

#include <linux/clk.h>
+#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/mii.h>
@@ -684,8 +685,33 @@ int smsc_phy_probe(struct phy_device *phydev)
}
EXPORT_SYMBOL_GPL(smsc_phy_probe);

+static int lan83c183_resume(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = phy_modify_changed(phydev, MII_BMCR, BMCR_PDOWN, 0);
+ if (ret < 0)
+ return ret;
+
+ /* The PHY needs up to 500 ms to restore operation after power-down. */
+ if (ret)
+ msleep(500);
+
+ return 0;
+}
+
static struct phy_driver smsc_phy_driver[] = {
{
+ /* LSI/SEEQ OUI 00:a0:7d, model 4; shared with L80227. */
+ .phy_id = 0x0016f840,
+ .phy_id_mask = 0xfffffff0,
+ .name = "SMSC LAN83C183",
+
+ .get_features = genphy_read_abilities,
+ .suspend = genphy_suspend,
+ .resume = lan83c183_resume,
+ .set_loopback = genphy_loopback,
+}, {
.phy_id = 0x0007c0a0, /* OUI=0x00800f, Model#=0x0a */
.phy_id_mask = 0xfffffff0,
.name = "SMSC LAN83C185",
@@ -887,6 +913,7 @@ MODULE_AUTHOR("Herbert Valerio Riedel");
MODULE_LICENSE("GPL");

static const struct mdio_device_id __maybe_unused smsc_tbl[] = {
+ { 0x0016f840, 0xfffffff0 },
{ 0x0007c0a0, 0xfffffff0 },
{ 0x0007c0b0, 0xfffffff0 },
{ 0x0007c0c0, 0xfffffff0 },
--
2.53.0