Here is some info about my problem with an adaptec 2940 and a Wangtek
tape. When the machine hangs I get the following output:
SCSI0 Parity error during phase Data-Out on target 4, channel 0, lun0.
SCSI0 Parity error during phase Data-Out on target 4, channel 0, lun0.
SCSI0 channel 0: resetting for second half of retries.
SCSI bus is being reset for host 0 channel 0
aic7xxx: (reset) target/channel 4/0
aic7xxx: (reset_device) target/channel -1/A to scb 4/A
aic7xxx: (match_scb) comparing target/channel -1/A to scb 4/A
aic7xxx: (reset_device) aborting SCB1, TCL=4/0/0
aic7xxx: (match_scb) comparing target/channel -1/A to scb 4/A
aic7xxx: (reset_device) aborting SCB1, TCL=4/0/0
aic7xxx: (match_scb) comparing target/channel -1/A to scb 4/A
aic7xxx: (reset_channel) Resetting current channel
aic7xxx: (reset_channel) Chanel reset, sequencer restarted
After this it's completely dead.
On bootup I get the following information about the scsi-card and
tape/disks:
aic7xxx: BurstLen = 8 DWDs, Latency Timer = 64 PCLKS
aic7xxx: AHA-2940 Rev B.
aic7xxx: devconfig = 0x500.
aic7xxx: Reading SEEPROM...done.
aic7xxx: Extended translation enabled.
aic7xxx: Memory check yields 16 SCBs, paging not enabled.
AHA-2940 (PCI-bus), I/O 0xfc00, Mem 0xfffbf000:
irq 11
bus release time 40 bclks
data fifo threshold 100%
SCSI CHANNEL A:
scsi id 7
scsi selection timeout 256 ms
scsi bus reset at power-on enabled
scsi bus parity enabled
scsi bus termination (low byte) disabled
aic7xxx: Downloading sequencer code...done.
aic7xxx: Resetting the SCSI bus...done.
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 3.4/3.2/3.1
scsi : 1 host.
scsi0: Scanning channel A for devices.
scsi0: Target 0, channel A, now synchronous at 10.0MHz, offset 15.
Vendor: Quantum Model: XP34300 Rev: 81HB
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi0: Target 3, channel A, refusing synchronous negotiation; using
asynchronous transfers.
Vendor: DEC Model: TLZ04 1989(C)DEC Rev: 1615
Type: Sequential-Access ANSI SCSI revision: 02
Detected scsi tape st0 at scsi0, channel 0, id 3, lun 0
scsi0: Target 4, channel A, now synchronous at 10.0MHz, offset 15.
Vendor: COMPAQ Model: ST15150N Rev: 5216
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 4, lun 0
scsi0: Target 5, channel A, refusing synchronous negotiation; using
asynchronous transfers.
Vendor: WANGTEK Model: 5150ES SCSI FA23 Rev: 08
Type: Sequential-Access ANSI SCSI revision: 01
Detected scsi tape st1 at scsi0, channel 0, id 5, lun 0
scsi0: Target 6, channel A, now synchronous at 5.0MHz, offset 12.
Vendor: NEC Model: CD-ROM DRIVE:500 Rev: 2.5
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
scsi : detected 2 SCSI tapes 1 SCSI cdrom 2 SCSI disks total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 8399520 [4101 MB] [4.1
GB]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 8386000 [4094 MB] [4.1
GB]
The error appears everytime I try to read a tape from /dev/st1 and didn't
appear in 2.0.12
/Alex
- --
+-----------------------+---------------------------------------------+
| Alex Frausin | Linux > Solaris, HP-UX, BSD, MacOS, Win95.. |
| | |
| | Opinions all mine |
| Phone +46 31 772 8328 | http://alice.gd.chalmers.se/~alex |
| | |
+-----------------------+---------------------------------------------+
-----BEGIN PGP SIGNATURE-----
Version: 2.6.3ia
Charset: noconv
iQB1AwUBMhuM7vkgghhdb7RhAQG61QL8DNRhLUGrd6PbWPZbvKmRsPNgMDBt1ce9
KvQeD6fxAJd+YKqp3NOQVOZ6QOOg5kbWqoNAPs8aIp36DdKUozztheghzhemmtNf
OqNPPiR6BDb2TSPubW+TuJykm0f+LA1o
=Gp89
-----END PGP SIGNATURE-----