Mouse support is specified in the XF86Config file,
and the fact that the mouse config shows as supplied
info, not probed info, means that the system might
not really be finding the mouse.
Another potential problem is that sometimes GPM
(general purpose mouse support) conflicts with
XWindows. You may need to remove /etc/rc.d/rc.gpm .
Hope this helps.
Mishelle Bradford
______________________________________________________
On Thu, 22 Aug 1996, Rajnish Sinha wrote:
>
> I am trying to install X windows on linux. My linux version is
> 1.2.13 with a patch for IP in IP tunnelling support. I have
> installed XFree86 version 3.1.2 with files from the elf and common
> distribution.
>
> I am using a NEC Versa 4050C laptop.
> My laptop has Super VGA or SVGA video and I installed
> the file X32SVGA.tgz from the XFree86 distribution.
> I got the XF86config file for NEC Versa from the Linux laptops
> home page.
> I followed the instructions given in the INSTALL document to install
> the X software.
>
> I was able to run X when I used linux kernel version 1.2.13.
> But when I added the patch for IP in IP,
> I get the following error message when I start X.
> As you see in the error message, PS2 mouse support is recognized.
>
> Any suggestions on what I can do to make this work?
>
> Thanks
>
>
> XFree86 Version 3.1.2 / X Window System
> (protocol Version 11, revision 0, vendor release 6000)
> Operating System: Linux
> Configured drivers:
> SVGA: server for 8-bit colour SVGA (Patchlevel 0):
> et4000, et4000w32, et4000w32i, et4000w32p, et3000, pvga1, wd90c00,
> wd90c10, wd90c30, wd90c24, wd90c31, wd90c33, gvga, vgawonder,
> tvga8800cs, tvga8900b, tvga8900c, tvga8900cl, tvga9000, clgd5420,
> clgd5422, clgd5424, clgd5426, clgd5428, clgd5429, clgd5430,
> clgd5434,
> clgd5436, clgd6205, clgd6215, clgd6225, clgd6235, ncr77c22,
> ncr77c22e,
> cpq_avga, oti067, oti077, oti087, mx, al2101, ali2228, ali2301,
> ali2302, ali2308, ali2401, cl6410, cl6412, cl6420, cl6440, video7,
> ct65520, ct65530, ct65540, ct65545, ark1000vl, ark1000pv,
> ark2000pv,
> realtek, generic
> (using VT number 7)
>
> XF86Config: /usr/X11R6/lib/X11/XF86Config
> (**) stands for supplied, (--) stands for probed/default values
> (**) Mouse: type: PS/2, device: /dev/psaux, baudrate: 1200,
> 3 button emulation (timeout: 50ms)
> (**) SVGA: Graphics device ID: "Laptop"
> (**) SVGA: Monitor ID: "C&T Laptop"
> (**) FontPath set to "/usr/X11R6/lib/X11/fonts/misc/"
> (**) SVGA: chipset: ct65545
> (**) SVGA: videoram: 1024k
> (--) SVGA: clocks: 28.38 28.32 28.33 28.32 28.37 28.32 28.32
> 28.39
> (--) SVGA: Maximum allowed dot-clock: 65.000 MHz
> (--) SVGA: There is no defined dot-clock matching mode "1024x768"
> (--) SVGA: Removing mode "1024x768" from list of valid modes.
> (--) SVGA: There is no mode definition named "800+600"
> (--) SVGA: Removing mode "800+600" from list of valid modes.
> (**) SVGA: Mode "800x600": mode clock = 28.300, clock used = 28.320
> (--) SVGA: There is no mode definition named "704x600"
> (--) SVGA: Removing mode "704x600" from list of valid modes.
> (**) SVGA: Mode "640x480": mode clock = 28.300, clock used = 28.320
> (--) SVGA: Virtual resolution set to 800x600
> (--) SVGA: SpeedUp code selection modified because virtualX != 1024
>
> Fatal server error:
> Cannot open mouse (Device or resource busy)
>
> xinit: No such file or directory (errno 2): unexpected signal 13
>
>