scsi : aborting command due to timeout : pid 55794, scsi0, channel 0, id 0,
lun 0 Read (6) 1d 01 d2 62 00
aic7xxx: (abort) Aborting scb 1, TCL 0/0/0
scsi : aborting command due to timeout : pid 55797, scsi0, channel 0, id 1,
lun 0 Write (6) 06 80 2a 04 00
aic7xxx: (abort) Aborting scb 2, TCL 1/0/0
scsi : aborting command due to timeout : pid 55798, scsi0, channel 0, id 1,
lun 0 Write (6) 06 80 32 04 00
aic7xxx: (abort) Aborting scb 4, TCL 1/0/0
scsi : aborting command due to timeout : pid 55796, scsi0, channel 0, id 0,
lun 0 Write (6) 06 40 02 04 00
aic7xxx: (abort) Aborting scb 3, TCL 0/0/0
...and here's the dmesg stuff relating to scsi:
aic7xxx: BurstLen = 8 DWDs, Latency Timer = 240 PCLKS
aic7xxx: AHA-2940 Rev B.
aic7xxx: devconfig = 0x500.
aic7xxx: Reading SEEPROM...done.
aic7xxx: Extended translation disabled.
aic7xxx: Memory check yields 16 SCBs, paging not enabled.
AHA-2940 (PCI-bus), I/O 0xf800, Mem 0xffbef000:
irq 10
bus release time 40 bclks
data fifo threshold 100%
SCSI CHANNEL A:
scsi id 7
scsi selection timeout 256 ms
scsi bus reset at power-on enabled
scsi bus parity enabled
scsi bus termination (low byte) disabled
aic7xxx: Downloading sequencer code...done.
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 4.0/3.2/4.0
scsi : 1 host.
scsi0: Scanning channel A for devices.
scsi0: Target 0, channel A, now synchronous at 10.0MHz, offset 15.
Vendor: IBM Model: DPES-31080 !t Rev: S31K
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi0: Target 1, channel A, now synchronous at 4.4MHz, offset 15.
Vendor: MAXTOR Model: LXT-340S Rev: 6.55
Type: Direct-Access ANSI SCSI revision: 01 CCS
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
scsi0: Target 2, channel A, now synchronous at 4.0MHz, offset 15.
Vendor: TOSHIBA Model: CD-ROM XM-3601TA Rev: 0725
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0
scsi0: Target 4, channel A, now synchronous at 6.67MHz, offset 15.
Vendor: ARCHIVE Model: Python 28388-XXX Rev: 5.45
Type: Sequential-Access ANSI SCSI revision: 02
Detected scsi tape st0 at scsi0, channel 0, id 4, lun 0
scsi : detected 1 SCSI tape 1 SCSI cdrom 2 SCSI disks total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2118144 [1034 MB] [1.0 GB]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 665154 [324 MB] [0.3 GB]
Michael
-- Michael Nelson nelson@seahunt.imat.com San Francisco, CA