Thansk! This patch indeed fixes the problem where both sym53c8xx and ncr53c8xx
wanted to play with the same SCSI adapter.
However, now a different problem showed up (with vger-August 24/2.3.15-preXX
on PPC):
| sym53c8xx: at PCI bus 0, device 6, function 0
| sym53c8xx: setting PCI_COMMAND_IO PCI_COMMAND_MEMORY...
| sym53c8xx: setting PCI_COMMAND_MASTER PCI_COMMAND_PARITY...(fix-up)
| sym53c8xx: 53c875 detected
| sym53c875-0: rev=0x04, base=0xc3000000, io_port=0x1400, irq=31
| sym53c875-0: NCR clock is 40218KHz, 40218KHz
| sym53c875-0: ID 7, Fast-20, Parity Checking
| sym53c875-0: on-chip RAM at 0xc3001000
| sym53c875-0: restart (scsi reset).
| sym53c875-0: Downloading SCSI SCRIPTS.
| ncr53c8xx: at PCI bus 0, device 6, function 0
| ncr53c8xx: IO region 0x1400 to 0x147f is in use
| mesh: assuming 50MHz clock frequency
| scsi0 : sym53c8xx - version 1.3c
| scsi1 : MESH
| scsi : 2 hosts.
| scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00
| sym53c8xx_abort: pid=0 serial_number=1 serial_number_at_timeout=1
And then the system hangs in a wait loop...
My devices (from 2.3.6 dmesg):
| Vendor: QUANTUM Model: VIKING II 4.5WLS Rev: 3506
| Type: Direct-Access ANSI SCSI revision: 02
| Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
| Vendor: PLEXTOR Model: CD-ROM PX-12TS Rev: 1.02
| Type: CD-ROM ANSI SCSI revision: 02
| Vendor: HP Model: HP35480A Rev: T503
| Type: Sequential-Access ANSI SCSI revision: 02
| sym53c875-0-<0,0>: tagged command queue depth set to 8
| Vendor: QUANTUM Model: FIREBALL_TM3200S Rev: 300X
| Type: Direct-Access ANSI SCSI revision: 02
| Detected scsi disk sdb at scsi1, channel 0, id 5, lun 0
| scsi : detected 2 SCSI disks total.
| sym53c875-0-<0,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 16)
| SCSI device sda: hdwr sector= 512 bytes. Sectors= 8910423 [4350 MB] [4.4 GB]
| SCSI device sdb: hdwr sector= 512 bytes. Sectors= 6281856 [3067 MB] [3.1 GB]
The last kernel that worked on my machine (CHRP LongTrail) was 2.3.10 (a bit
unstable), but I'm using 2.3.6 right now since it's more stable.
Any clues?
Greetings,
Geert
-- Geert Uytterhoeven Geert.Uytterhoeven@cs.kuleuven.ac.be Wavelets, Linux/{m68k~Amiga,PPC~CHRP} http://www.cs.kuleuven.ac.be/~geert/ Department of Computer Science -- Katholieke Universiteit Leuven -- Belgium
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/