[PATCH v3 13/17] i3c: renesas: Update HW registers after SW computations are done

[Claudiu Beznea]

From: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>

renesas_i3c_bus_init() performs a number of computations and software
cache updates, interleaving them with hardware register writes. While
this works today, it makes it harder to minimize the time the controller
must remain powered when runtime PM is introduced.

Perform all software computations and cache updates first, then update
the hardware registers. This prepares for future runtime PM support.

Reviewed-by: Frank Li <Frank.Li@xxxxxxx>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>
---

Changes in v3:
- none

Changes in v2:
- collected tags

 drivers/i3c/master/renesas-i3c.c | 28 ++++++++++++++--------------
 1 file changed, 14 insertions(+), 14 deletions(-)

diff --git a/drivers/i3c/master/renesas-i3c.c b/drivers/i3c/master/renesas-i3c.c
index dab643cd8859..38ce722881da 100644
--- a/drivers/i3c/master/renesas-i3c.c
+++ b/drivers/i3c/master/renesas-i3c.c
@@ -560,10 +560,6 @@ static int renesas_i3c_bus_init(struct i3c_master_controller *m)
 	if (!i3c->rate)
 		return -EINVAL;
 
-	ret = renesas_i3c_reset(i3c);
-	if (ret)
-		return ret;
-
 	i2c_total_ticks = DIV_ROUND_UP(i3c->rate, bus->scl_rate.i2c);
 	i3c_total_ticks = DIV_ROUND_UP(i3c->rate, bus->scl_rate.i3c);
 
@@ -614,27 +610,31 @@ static int renesas_i3c_bus_init(struct i3c_master_controller *m)
 			STDBR_SBRHO(double_SBR, od_high_ticks) |
 			STDBR_SBRLP(pp_low_ticks) |
 			STDBR_SBRHP(pp_high_ticks);
-	renesas_writel(i3c->regs, STDBR, i3c->i3c_STDBR);
 
 	/* Extended Bit Rate setting */
 	i3c->extbr = EXTBR_EBRLO(od_low_ticks) | EXTBR_EBRHO(od_high_ticks) |
 		     EXTBR_EBRLP(pp_low_ticks) | EXTBR_EBRHP(pp_high_ticks);
-	renesas_writel(i3c->regs, EXTBR, i3c->extbr);
-
-	renesas_writel(i3c->regs, REFCKCTL, REFCKCTL_IREFCKS(cks));
-	i3c->refclk_div = cks;
-
-	/* I3C hw init*/
-	renesas_i3c_hw_init(i3c);
 
 	ret = i3c_master_get_free_addr(m, 0);
 	if (ret < 0)
 		return ret;
 
+	info.dyn_addr = ret;
 	i3c->dyn_addr = ret;
-	renesas_writel(i3c->regs, MSDVAD, MSDVAD_MDYAD(ret) | MSDVAD_MDYADV);
+	i3c->refclk_div = cks;
+
+	ret = renesas_i3c_reset(i3c);
+	if (ret)
+		return ret;
+
+	renesas_writel(i3c->regs, STDBR, i3c->i3c_STDBR);
+	renesas_writel(i3c->regs, EXTBR, i3c->extbr);
+	renesas_writel(i3c->regs, REFCKCTL, REFCKCTL_IREFCKS(cks));
+	renesas_writel(i3c->regs, MSDVAD, MSDVAD_MDYAD(i3c->dyn_addr) | MSDVAD_MDYADV);
+
+	/* I3C hw init*/
+	renesas_i3c_hw_init(i3c);
 
-	info.dyn_addr = ret;
 	return i3c_master_set_info(&i3c->base, &info);
 }
 
-- 
2.43.0