[PATCH 1/9] staging: rtl8723bs: hal: fix whitespace in sdio_halinit.c
From: Quentin Strydom
Date: Thu Jun 11 2026 - 12:38:55 EST
Remove spaces before tabs in comments to match kernel coding style.
Signed-off-by: Quentin Strydom <qstrydom0@xxxxxxxxx>
---
drivers/staging/rtl8723bs/hal/sdio_halinit.c | 54 ++++++++++----------
1 file changed, 27 insertions(+), 27 deletions(-)
diff --git a/drivers/staging/rtl8723bs/hal/sdio_halinit.c b/drivers/staging/rtl8723bs/hal/sdio_halinit.c
index f2f73c65a636..694cd4eca970 100644
--- a/drivers/staging/rtl8723bs/hal/sdio_halinit.c
+++ b/drivers/staging/rtl8723bs/hal/sdio_halinit.c
@@ -46,7 +46,7 @@ u8 _InitPowerOn_8723BS(struct adapter *padapter)
u16 value16;
u32 value32;
u8 ret;
-/* u8 bMacPwrCtrlOn; */
+/* u8 bMacPwrCtrlOn; */
/* all of these MUST be configured before power on */
@@ -70,8 +70,8 @@ u8 _InitPowerOn_8723BS(struct adapter *padapter)
rtw_write16(padapter, REG_APS_FSMCO, value16);
/* Enable CMD53 R/W Operation */
-/* bMacPwrCtrlOn = true; */
-/* rtw_hal_set_hwreg(padapter, HW_VAR_APFM_ON_MAC, &bMacPwrCtrlOn); */
+/* bMacPwrCtrlOn = true; */
+/* rtw_hal_set_hwreg(padapter, HW_VAR_APFM_ON_MAC, &bMacPwrCtrlOn); */
rtw_write8(padapter, REG_CR, 0x00);
/* Enable MAC DMA/WMAC/SCHEDULE/SEC block */
@@ -359,7 +359,7 @@ static void _InitNetworkType(struct adapter *padapter)
value32 = rtw_read32(padapter, REG_CR);
/* TODO: use the other function to set network type */
-/* value32 = (value32 & ~MASK_NETTYPE) | _NETTYPE(NT_LINK_AD_HOC); */
+/* value32 = (value32 & ~MASK_NETTYPE) | _NETTYPE(NT_LINK_AD_HOC); */
value32 = (value32 & ~MASK_NETTYPE) | _NETTYPE(NT_LINK_AP);
rtw_write32(padapter, REG_CR, value32);
@@ -487,7 +487,7 @@ static void _initSdioAggregationSetting(struct adapter *padapter)
struct hal_com_data *pHalData = GET_HAL_DATA(padapter);
/* Tx aggregation setting */
-/* sdio_AggSettingTxUpdate(padapter); */
+/* sdio_AggSettingTxUpdate(padapter); */
/* Rx aggregation setting */
HalRxAggr8723BSdio(padapter);
@@ -641,7 +641,7 @@ u32 rtl8723bs_hal_init(struct adapter *padapter)
}
/* Disable Interrupt first. */
-/* rtw_hal_disable_interrupt(padapter); */
+/* rtw_hal_disable_interrupt(padapter); */
ret = _InitPowerOn_8723BS(padapter);
if (ret == _FAIL)
@@ -661,7 +661,7 @@ u32 rtl8723bs_hal_init(struct adapter *padapter)
rtl8723b_InitializeFirmwareVars(padapter);
-/* SIC_Init(padapter); */
+/* SIC_Init(padapter); */
if (pwrctrlpriv->reg_rfoff)
pwrctrlpriv->rf_pwrstate = rf_off;
@@ -747,8 +747,8 @@ u32 rtl8723bs_hal_init(struct adapter *padapter)
/* Record original value for template. This is arough data, we can only use the data */
/* for power adjust. The value can not be adjustde according to different power!!! */
-/* pHalData->OriginalCckTxPwrIdx = pHalData->CurrentCckTxPwrIdx; */
-/* pHalData->OriginalOfdm24GTxPwrIdx = pHalData->CurrentOfdm24GTxPwrIdx; */
+/* pHalData->OriginalCckTxPwrIdx = pHalData->CurrentCckTxPwrIdx; */
+/* pHalData->OriginalOfdm24GTxPwrIdx = pHalData->CurrentOfdm24GTxPwrIdx; */
rtl8723b_InitAntenna_Selection(padapter);
@@ -791,7 +791,7 @@ u32 rtl8723bs_hal_init(struct adapter *padapter)
/* ack for xmit mgmt frames. */
rtw_write32(padapter, REG_FWHW_TXQ_CTRL, rtw_read32(padapter, REG_FWHW_TXQ_CTRL) | BIT(12));
-/* pHalData->PreRpwmVal = SdioLocalCmd52Read1Byte(padapter, SDIO_REG_HRPWM1) & 0x80; */
+/* pHalData->PreRpwmVal = SdioLocalCmd52Read1Byte(padapter, SDIO_REG_HRPWM1) & 0x80; */
{
pwrctrlpriv->rf_pwrstate = rf_on;
@@ -844,7 +844,7 @@ u32 rtl8723bs_hal_init(struct adapter *padapter)
/* */
/* Description: */
-/* RTL8723e card disable power sequence v003 which suggested by Scott. */
+/* RTL8723e card disable power sequence v003 which suggested by Scott. */
/* */
/* First created by tynli. 2011.01.28. */
/* */
@@ -856,7 +856,7 @@ static void CardDisableRTL8723BSdio(struct adapter *padapter)
/* Run LPS WL RFOFF flow */
HalPwrSeqCmdParsing(padapter, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, rtl8723B_enter_lps_flow);
- /* ==== Reset digital sequence ====== */
+ /* ==== Reset digital sequence ====== */
val = rtw_read8(padapter, REG_MCUFWDL);
if ((val & RAM_DL_SEL) && padapter->bFWReady) /* 8051 RAM code */
@@ -879,7 +879,7 @@ static void CardDisableRTL8723BSdio(struct adapter *padapter)
val |= BIT(0);
rtw_write8(padapter, REG_RSV_CTRL + 1, val);
- /* ==== Reset digital sequence end ====== */
+ /* ==== Reset digital sequence end ====== */
bMacPwrCtrlOn = false; /* Disable CMD53 R/W */
rtw_hal_set_hwreg(padapter, HW_VAR_APFM_ON_MAC, &bMacPwrCtrlOn);
@@ -981,13 +981,13 @@ void rtl8723bs_interface_configure(struct adapter *padapter)
}
/* */
-/* Description: */
-/* We should set Efuse cell selection to WiFi cell in default. */
+/* Description: */
+/* We should set Efuse cell selection to WiFi cell in default. */
/* */
-/* Assumption: */
-/* PASSIVE_LEVEL */
+/* Assumption: */
+/* PASSIVE_LEVEL */
/* */
-/* Added by Roger, 2010.11.23. */
+/* Added by Roger, 2010.11.23. */
/* */
static void _EfuseCellSel(struct adapter *padapter)
{
@@ -1073,24 +1073,24 @@ static void _ReadEfuseInfo8723BS(struct adapter *padapter)
static void _ReadPROMContent(struct adapter *padapter)
{
struct eeprom_priv *pEEPROM = GET_EEPROM_EFUSE_PRIV(padapter);
- u8 eeValue;
+ u8 eeValue;
eeValue = rtw_read8(padapter, REG_9346CR);
/* To check system boot selection. */
pEEPROM->EepromOrEfuse = (eeValue & BOOT_FROM_EEPROM) ? true : false;
pEEPROM->bautoload_fail_flag = (eeValue & EEPROM_EN) ? false : true;
-/* pHalData->EEType = IS_BOOT_FROM_EEPROM(Adapter) ? EEPROM_93C46 : EEPROM_BOOT_EFUSE; */
+/* pHalData->EEType = IS_BOOT_FROM_EEPROM(Adapter) ? EEPROM_93C46 : EEPROM_BOOT_EFUSE; */
_ReadEfuseInfo8723BS(padapter);
}
/* */
-/* Description: */
-/* Read HW adapter information by E-Fuse or EEPROM according CR9346 reported. */
+/* Description: */
+/* Read HW adapter information by E-Fuse or EEPROM according CR9346 reported. */
/* */
-/* Assumption: */
-/* PASSIVE_LEVEL (SDIO interface) */
+/* Assumption: */
+/* PASSIVE_LEVEL (SDIO interface) */
/* */
/* */
static s32 _ReadAdapterInfo8723BS(struct adapter *padapter)
@@ -1203,14 +1203,14 @@ void SetHwRegWithBuf8723B(struct adapter *padapter, u8 variable, u8 *pbuf, int l
}
/* */
-/* Description: */
-/* Query setting of specified variable. */
+/* Description: */
+/* Query setting of specified variable. */
/* */
u8 GetHalDefVar8723BSDIO(
struct adapter *Adapter, enum hal_def_variable eVariable, void *pValue
)
{
- u8 bResult = _SUCCESS;
+ u8 bResult = _SUCCESS;
switch (eVariable) {
case HAL_DEF_IS_SUPPORT_ANT_DIV:
--
2.43.0