[PATCH 1/5] ARM: dts: ls1021a-moxa-uc-8410a: add led suffix to fix CHECK_DTBS warnings
From: Frank . Li
Date: Wed Jul 08 2026 - 15:26:40 EST
From: Frank Li <Frank.Li@xxxxxxx>
Add led suffix to fix below CHECK_DTBS warnings:
ls1021a-moxa-uc-8410a.dtb: leds (gpio-leds): 'beeper', ... do not match
any of the regexes: '(^led-[0-9a-f]$|led)', '^pinctrl-[0-9]+$'
Signed-off-by: Frank Li <Frank.Li@xxxxxxx>
---
arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dts | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dts
index d2cae8c7d7a61..8efe6b615ca85 100644
--- a/arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dts
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dts
@@ -40,13 +40,13 @@ reg_3p3v: regulator-3p3v {
leds {
compatible = "gpio-leds";
- cel-pwr {
+ cel-pwr-led {
label = "UC8410A:CEL-PWR";
gpios = <&gpio3 27 GPIO_ACTIVE_LOW>;
default-state = "off";
};
- cel-reset {
+ cel-reset-led {
label = "UC8410A:CEL-RESET";
gpios = <&gpio3 28 GPIO_ACTIVE_LOW>;
default-state = "off";
@@ -58,13 +58,13 @@ str-led {
linux,default-trigger = "mmc0";
};
- sw-ready {
+ sw-ready-led {
label = "UC8410A:GREEN:SWRDY";
gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
- beeper {
+ beeper-led {
label = "UC8410A:BEEP";
gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
default-state = "off";
@@ -88,37 +88,37 @@ prog-led2 {
default-state = "off";
};
- wifi-signal0 {
+ wifi-signal0-led {
label = "UC8410A:GREEN:CEL2";
gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
- wifi-signal1 {
+ wifi-signal1-led {
label = "UC8410A:GREEN:CEL1";
gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
- wifi-signal2 {
+ wifi-signal2-led {
label = "UC8410A:GREEN:CEL0";
gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
- cpu-diag-red {
+ cpu-diag-red-led {
label = "UC8410A:RED:DIA";
gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
- cpu-diag-green {
+ cpu-diag-green-led {
label = "UC8410A:GREEN:DIA";
gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
- cpu-diag-yellow {
+ cpu-diag-yellow-led {
label = "UC8410A:YELLOW:DIA";
gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
default-state = "off";
--
2.43.0