Re: [PATCH V6 3/4] Bluetooth: btnxpuart: Add M.2 Bluetooth device support using pwrseq
From: Manivannan Sadhasivam
Date: Mon Jul 13 2026 - 00:57:21 EST
On Mon, Jul 13, 2026 at 10:34:34AM +0800, Sherry Sun (OSS) wrote:
> From: Sherry Sun <sherry.sun@xxxxxxx>
>
> Power supply to the M.2 Bluetooth device attached to the host using M.2
> connector is controlled using the 'uart' pwrseq device. So add support
> for getting the pwrseq device if the OF graph link is present.
>
> Once obtained, pwrseq_power_on() is called to power up the M.2 Bluetooth
> card. The power sequencer descriptor is obtained via pwrseq_get() with
> the UART controller device (serdev->ctrl->dev), since the OF graph
> link is defined on the UART controller node.
>
> Also add the explicit pwrseq_put() call in all exit paths, pwrseq_put()
> already calls pwrseq_power_off() internally, so no separate
> pwrseq_power_off() call is needed.
>
> Signed-off-by: Sherry Sun <sherry.sun@xxxxxxx>
Reviewed-by: Manivannan Sadhasivam <mani@xxxxxxxxxx>
- Mani
> Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxxxxxxxx>
> Reviewed-by: Frank Li <Frank.Li@xxxxxxx>
> ---
> Hi Frank and Bartosz, this V6 patch using pwrseq_put() in all exit paths to
> fix the power sequencer reference leak issue during BT driver unload and
> reload as reported by sashiko. I'm keeping your Reviewed-by tag. I can
> remove it if you think it's inappropriate.
> ---
> drivers/bluetooth/btnxpuart.c | 34 ++++++++++++++++++++++++++++++----
> 1 file changed, 30 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/bluetooth/btnxpuart.c b/drivers/bluetooth/btnxpuart.c
> index 0bb300eef157..81a11ac05114 100644
> --- a/drivers/bluetooth/btnxpuart.c
> +++ b/drivers/bluetooth/btnxpuart.c
> @@ -9,6 +9,8 @@
>
> #include <linux/serdev.h>
> #include <linux/of.h>
> +#include <linux/of_graph.h>
> +#include <linux/pwrseq/consumer.h>
> #include <linux/skbuff.h>
> #include <linux/unaligned.h>
> #include <linux/firmware.h>
> @@ -211,6 +213,7 @@ struct btnxpuart_dev {
>
> struct ps_data psdata;
> struct btnxpuart_data *nxp_data;
> + struct pwrseq_desc *pwrseq;
> struct reset_control *pdn;
> struct hci_uart hu;
> };
> @@ -1872,11 +1875,26 @@ static int nxp_serdev_probe(struct serdev_device *serdev)
> return err;
> }
>
> + if (of_graph_is_present(dev_of_node(&serdev->ctrl->dev))) {
> + struct pwrseq_desc *pwrseq;
> +
> + pwrseq = pwrseq_get(&serdev->ctrl->dev, "uart");
> + if (IS_ERR(pwrseq))
> + return dev_err_probe(&serdev->dev, PTR_ERR(pwrseq),
> + "failed to get pwrseq\n");
> +
> + nxpdev->pwrseq = pwrseq;
> + err = pwrseq_power_on(pwrseq);
> + if (err)
> + goto err_pwrseq_put;
> + }
> +
> /* Initialize and register HCI device */
> hdev = hci_alloc_dev();
> if (!hdev) {
> dev_err(&serdev->dev, "Can't allocate HCI device\n");
> - return -ENOMEM;
> + err = -ENOMEM;
> + goto err_pwrseq_put;
> }
>
> reset_control_deassert(nxpdev->pdn);
> @@ -1907,13 +1925,16 @@ static int nxp_serdev_probe(struct serdev_device *serdev)
> if (bacmp(&ba, BDADDR_ANY))
> hci_set_quirk(hdev, HCI_QUIRK_USE_BDADDR_PROPERTY);
>
> - if (hci_register_dev(hdev) < 0) {
> + err = hci_register_dev(hdev);
> + if (err < 0) {
> dev_err(&serdev->dev, "Can't register HCI device\n");
> goto probe_fail;
> }
>
> - if (ps_setup(hdev))
> + if (ps_setup(hdev)) {
> + err = -ENODEV;
> goto probe_fail_unregister;
> + }
>
> hci_devcd_register(hdev, nxp_coredump, nxp_coredump_hdr,
> nxp_coredump_notify);
> @@ -1925,7 +1946,10 @@ static int nxp_serdev_probe(struct serdev_device *serdev)
> probe_fail:
> reset_control_assert(nxpdev->pdn);
> hci_free_dev(hdev);
> - return -ENODEV;
> +err_pwrseq_put:
> + if (nxpdev->pwrseq)
> + pwrseq_put(nxpdev->pwrseq);
> + return err;
> }
>
> static void nxp_serdev_remove(struct serdev_device *serdev)
> @@ -1952,6 +1976,8 @@ static void nxp_serdev_remove(struct serdev_device *serdev)
> ps_cleanup(nxpdev);
> hci_unregister_dev(hdev);
> reset_control_assert(nxpdev->pdn);
> + if (nxpdev->pwrseq)
> + pwrseq_put(nxpdev->pwrseq);
> hci_free_dev(hdev);
> }
>
> --
> 2.50.1
>
--
மணிவண்ணன் சதாசிவம்