[PATCH v2 0/6] Add CCI and CAMSS support for Glymur

[Nihal Kumar Gupta]

This series adds the camera device tree support for the Qualcomm
Glymur SoC and enables it on the Glymur CRD board, which adds CCI
support and enables the OV08X40 sensor via CSIPHY4.

This series has been tested using the following commands with OV08X40 sensor.
- media-ctl --reset
- media-ctl -d /dev/media0 -V '"ov08x40 6-0036":0[fmt:SGRBG10_1X10/3856x2416 field:none]'
- media-ctl -d /dev/media0 -V '"msm_csiphy4":0[fmt:SGRBG10_1X10/3856x2416]'
- media-ctl -d /dev/media0 -V '"msm_csid0":0[fmt:SGRBG10_1X10/3856x2416]'
- media-ctl -d /dev/media0 -V '"msm_vfe0_rdi0":0[fmt:SGRBG10_1X10/3856x2416]'
- media-ctl -d /dev/media0 -l '"msm_csiphy4":1->"msm_csid0":0[1]'
- media-ctl -d /dev/media0 -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
- yavta -B capture-mplane -c -I -n 5 -f SGRBG10P -s 3856x2416 -F /dev/video0

Depends-on: https://lore.kernel.org/all/20261014-pm8010_i2c_support-v2-0-b395d2b3f668@xxxxxxxxxxxxxxxx/
---
Changes in v2:
- Glymur CAMSS dt-bindings and driver merged into linux-next.
- Rebased on next-20261014
- Nodes without a unit address should be sorted alphabetically - Konrad
- CAMSS node need to be sorted based on address - Konrad
- Moved operating-points-v2 to before status - Konrad
- Collect RB's and Tested-By tags from Konrad, Abel
- Link to v1: https://lore.kernel.org/r/20260907-glymur_camss_dts-v1-0-6c2ced5ea5f9@xxxxxxxxxxxxxxxx

Chnages in v1:
Internally reviewed by Konrad Dybcio:
1. [patch 1] Remove stray blank line above CAMSS node; keep blank line
   between last property and first subnode
2. [patch 2] Use preferred phandle list format for CCI: foo = <&bar>, <&xyz>
3. [patch 4] Replace qcom,pm8008 with correct qcom,pm8010-i2c compatible;
4. [patch 5] Move csiphy4 port@0 endpoint to SoC DTSI; reference by
   label in board DTSI
5. [patch 5] Reference camss_csiphy4_ep by label instead of redefining inline.

Signed-off-by: Nihal Kumar Gupta <nihal.gupta@xxxxxxxxxxxxxxxx>

---
Jishnu Prakash (1):
      arm64: dts: qcom: glymur-crd: Add PM8010 camera PMIC

Nihal Kumar Gupta (5):
      arm64: dts: qcom: glymur: Add CAMSS and CSIPHY nodes for Glymur
      arm64: dts: qcom: glymur: Add CCI definitions for Glymur
      arm64: dts: qcom: glymur: Add camera MCLK pinctrl
      arm64: dts: qcom: glymur-crd: Add ov08x40 RGB sensor on CSIPHY4
      arm64: defconfig: Enable OV08X40 camera sensor driver

 arch/arm64/boot/dts/qcom/glymur-crd.dtsi | 139 ++++++++
 arch/arm64/boot/dts/qcom/glymur.dtsi     | 557 +++++++++++++++++++++++++++++++
 arch/arm64/configs/defconfig             |   1 +
 3 files changed, 697 insertions(+)
---
base-commit: d419d682257d813f6cb7a28e42b35d0edf4ad038
change-id: 20260907-glymur_camss_dts-721052c08486

Best regards,
-- 
Nihal Kumar Gupta <nihal.gupta@xxxxxxxxxxxxxxxx>