Re: [PATCH v4 1/4] dt-bindings: connector: Add fsl,aud-io-slot binding

From: Chancel Liu

Date: Mon Nov 16 2026 - 03:14:49 EST


On 11/13/2026 6:53 AM, Rob Herring wrote:
> On Thu, Nov 05, 2026 at 03:41:14PM +0900, Chancel Liu wrote:
>> From: Chancel Liu <chancel.liu@xxxxxxx>
>>
>> The NXP AUD-IO slot represents a physically present I/O connector on
>> the base board. It acts as a nexus that exposes a constrained set of
>> I/O resources, such as GPIOs, clocks and interrupts, through fixed
>> electrical wiring. All actual hardware providers reside on the base
>> board. The connector node only defines index-based mappings to those
>> providers.
>>
>> This connector type is present on i.MX95 19x19 EVK and i.MX952 EVK,
>> where it is used to attach the IMX-AUD-IO audio expansion card[1]. The
>> same add-on board can be reused across different base boards that carry
>> this connector.
>>
>> [1]https://www.nxp.com/part/IMX-AUD-IO
>
> That link is pretty much useless. Is there a pinout definition
> somewhere?
>

The detailed user manual (UM12022) is listed as official documentation:
https://docs.nxp.com/bundle/UM12022/page/topics/pcie_interface1.html
But it is behind an NXP login.

The brief pinout table looks like this:

Pin Signal Dir
---- ------------------ ---
A11 PCI_AUD_RST_B In (GPIO)
A12 AUD_CARD_DET Out (INT)
A21 AUD_SPI7_SCLK In
A22 AUD_SPI7_SS0 In
A25 AUD_SPI7_MOSI In
A26 AUD_SPI7_MISO Out
A29 AUD_SPI7_SCLK In
A30 AUD_SPI7_SS0 In
A32 AUD_SPI7_MISO Out
A33 AUD_SPI7_MOSI In
B5 I2C6_SCL_1V8 In
B6 I2C6_SDA_1V8 I/O
B10 AUD_SLOT_PWR_SYNC In (GPIO)
B11 AUD_SLOT_PWRDN In (GPIO)
B12 AUD_SLOT_MCLK In (CLK)
B14 AUD_SLOT_INT_B Out (INT)
B15 AUD_SLOT_INT_B Out
B17 AUD_SLOT_INT_B Out
B23 SAI2_RXFS Out
B24 SAI2_RXC Out
B27 SAI2_TXD1 In
B28 SAI2_TXD2 In
B30 SAI2_TXD3 In
B31 SAI2_RXD1 Out
A2, A3, B1, B2, B3 VCC_EXT_12V0
B8, A9, A10 VCC_EXT_3V3

> Looking at the overlay, this looks incomplete. It looks like there's I2C
> thru the connector for example. There's also power rails.
>
> The idea with connectors is that overlays apply to the connector node
> and nothing else.

For this patch set, I2C, I2S and regulators are
provided by the base boards using a common set of labels:

aud_io_i2c
aud_io_cpu
aud_io_reg_1v8
aud_io_reg_3v3
aud_io_reg_5v

The common add-on board overlay references these labels directly. This
allows the same overlay to be used with both base boards. But the
overlay still depends on nodes outside the connector.

> I2C we've kind of figured out with something like this:
>
> connector {
> i2c-parent = <&i2c>;
> i2c {
> ...
> };
> };
>

I will rework the I2C part using this model.

> Regulators is still open issue though.
>
> Rob

Good to know this is being discussed. Is there a mailing-list thread or
patch series I can follow?

Regards,
Chancel Liu