Re: [PATCH v4 1/4] dt-bindings: connector: Add fsl,aud-io-slot binding

From: Rob Herring

Date: Mon Nov 16 2026 - 11:01:20 EST


On Mon, Nov 16, 2026 at 04:14:26PM +0800, Chancel Liu wrote:
> On 11/13/2026 6:53 AM, Rob Herring wrote:
> > On Thu, Nov 05, 2026 at 03:41:14PM +0900, Chancel Liu wrote:
> >> From: Chancel Liu <chancel.liu@xxxxxxx>
> >>
> >> The NXP AUD-IO slot represents a physically present I/O connector on
> >> the base board. It acts as a nexus that exposes a constrained set of
> >> I/O resources, such as GPIOs, clocks and interrupts, through fixed
> >> electrical wiring. All actual hardware providers reside on the base
> >> board. The connector node only defines index-based mappings to those
> >> providers.
> >>
> >> This connector type is present on i.MX95 19x19 EVK and i.MX952 EVK,
> >> where it is used to attach the IMX-AUD-IO audio expansion card[1]. The
> >> same add-on board can be reused across different base boards that carry
> >> this connector.
> >>
> >> [1]https://www.nxp.com/part/IMX-AUD-IO
> >
> > That link is pretty much useless. Is there a pinout definition
> > somewhere?
> >
>
> The detailed user manual (UM12022) is listed as official documentation:
> https://docs.nxp.com/bundle/UM12022/page/topics/pcie_interface1.html
> But it is behind an NXP login.
>
> The brief pinout table looks like this:
>
> Pin Signal Dir
> ---- ------------------ ---
> A11 PCI_AUD_RST_B In (GPIO)
> A12 AUD_CARD_DET Out (INT)
> A21 AUD_SPI7_SCLK In
> A22 AUD_SPI7_SS0 In
> A25 AUD_SPI7_MOSI In
> A26 AUD_SPI7_MISO Out
> A29 AUD_SPI7_SCLK In
> A30 AUD_SPI7_SS0 In
> A32 AUD_SPI7_MISO Out
> A33 AUD_SPI7_MOSI In
> B5 I2C6_SCL_1V8 In
> B6 I2C6_SDA_1V8 I/O
> B10 AUD_SLOT_PWR_SYNC In (GPIO)
> B11 AUD_SLOT_PWRDN In (GPIO)
> B12 AUD_SLOT_MCLK In (CLK)
> B14 AUD_SLOT_INT_B Out (INT)
> B15 AUD_SLOT_INT_B Out
> B17 AUD_SLOT_INT_B Out
> B23 SAI2_RXFS Out
> B24 SAI2_RXC Out
> B27 SAI2_TXD1 In
> B28 SAI2_TXD2 In
> B30 SAI2_TXD3 In
> B31 SAI2_RXD1 Out
> A2, A3, B1, B2, B3 VCC_EXT_12V0
> B8, A9, A10 VCC_EXT_3V3
>
> > Looking at the overlay, this looks incomplete. It looks like there's I2C
> > thru the connector for example. There's also power rails.
> >
> > The idea with connectors is that overlays apply to the connector node
> > and nothing else.
>
> For this patch set, I2C, I2S and regulators are
> provided by the base boards using a common set of labels:
>
> aud_io_i2c
> aud_io_cpu
> aud_io_reg_1v8
> aud_io_reg_3v3
> aud_io_reg_5v
>
> The common add-on board overlay references these labels directly. This
> allows the same overlay to be used with both base boards. But the
> overlay still depends on nodes outside the connector.

Using labels is a solution, but not one I particularly like because that
makes labels an ABI yet we don't document them.


> > I2C we've kind of figured out with something like this:
> >
> > connector {
> > i2c-parent = <&i2c>;
> > i2c {
> > ...
> > };
> > };
> >
>
> I will rework the I2C part using this model.
>
> > Regulators is still open issue though.
> >
> > Rob
>
> Good to know this is being discussed. Is there a mailing-list thread or
> patch series I can follow?

Search lore. There's been a number of connector series over the years.
gpio-map, clock-map, pwm-map have all come out of those discussions.

Rob