Re: [PATCH v3 3/3] arm64: dts: allwinner: add Radxa Cubie A7S board
From: Alexander Sverdlin
Date: Wed Nov 18 2026 - 13:04:49 EST
Hi Enzo,
On Mon, 2026-11-09 at 23:45 -0500, Enzo Adriano wrote:
> Enable the Cubie A7S serial console, PMIC and microSD slot to provide
> an initial usable board configuration. Supply the 26 MHz crystal and
> 32768 Hz RTC input, enable UART0 and the AXP318W on R-I2C0, and describe
> the PMIC input/output and CPU supply connections from the Radxa Cubie
> A7S schematic v1.10. Preserve firmware settings on rails whose working
> voltage is not established. BLDO2 has no programmed voltage constraint:
> its software 3.3 V selector does not establish its physical output with
> the schematic's nominal 2.4 V input.
>
> Describe the card's SWOUT2 supply and PF6 active-high detect with an
> internal pull-down. Enable MMC0 at up to 50 MHz using 3.3 V signaling
> only. Its high-voltage path uses VCCIO; CLDO5 also feeds PC and the PF
> 1.8 V input and must not be raised for SD signaling. Firmware must
> select the 3.3 V PF path; dynamic voltage switching is not provided.
> Keep other storage off.
>
> Connect the documented bank supplies. PL's self-supply phandle is
> omitted to avoid the PMIC/I2C/pinctrl bootstrap cycle, as on the
> upstream Cubie A5E; ALDO1 is retained always-on. The separate pinctrl
> voltage-mode fix is required for these bank-supply connections.
>
> These board DTS bytes were RAM-booted on a Cubie A7S with vendor
> firmware on November 4: UART0, PMIC registration and MMC0 read-only
> transfers worked. Card writes, physical hotplug, 1.8 V signaling and
> physical BLDO2 voltage were not tested.
Should the history be moved below "---"?
> Signed-off-by: Enzo Adriano <enzo.adriano.code@xxxxxxxxx>
> ---
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../dts/allwinner/sun60i-a733-cubie-a7s.dts | 284 ++++++++++++++++++
> 2 files changed, 285 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7s.dts
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index d1f768dd6461..792152525b43 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -68,3 +68,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun55i-a527-cubie-a5e.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun55i-h728-x96qpro+.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-avaota-a1.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-orangepi-4a.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun60i-a733-cubie-a7s.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7s.dts b/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7s.dts
> new file mode 100644
> index 000000000000..341c24360ce2
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7s.dts
> @@ -0,0 +1,284 @@
> +// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
> +/dts-v1/;
> +
> +#include "sun60i-a733.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "Radxa Cubie A7S";
> + compatible = "radxa,cubie-a7s", "allwinner,sun60i-a733";
> +
> + aliases {
> + mmc0 = &mmc0;
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + reg_ps: regulator-system-power {
> + compatible = "regulator-fixed";
> + regulator-name = "ps";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + reg_ldo_input: regulator-ldo-input {
> + compatible = "regulator-fixed";
> + regulator-name = "ldo-input";
> + /* ETA3521: 0.6 V * (1 + RP298 / RP299), 30k / 10k. */
> + regulator-min-microvolt = <2400000>;
> + regulator-max-microvolt = <2400000>;
> + regulator-always-on;
> + vin-supply = <®_ps>;
> + };
> +
> + osc32k: osc32k-clk {
Should two regulators and the clock have been sorted in the reverse order?
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <®_dcdc5>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <®_dcdc5>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <®_dcdc5>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <®_dcdc5>;
> +};
> +
> +&cpu4 {
> + cpu-supply = <®_dcdc5>;
> +};
> +
> +&cpu5 {
> + cpu-supply = <®_dcdc5>;
> +};
> +
> +&cpu6 {
> + cpu-supply = <®_dcdc3>;
> +};
> +
> +&cpu7 {
> + cpu-supply = <®_dcdc3>;
> +};
> +
> +&mmc0 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cd-gpios = <&pio 5 6 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>;
> + disable-wp;
> + max-frequency = <50000000>;
> + no-1-8-v;
> + vmmc-supply = <®_swout2>;
> + /* The 3.3 V path uses VCC-IO; no Port F voltage switching yet. */
> + vqmmc-supply = <®_swout2>;
> + status = "okay";
see below...
> +};
> +
> +&osc {
> + clock-frequency = <26000000>;
> +};
> +
> +&pio {
> + vcc-pb-supply = <®_swout2>;
> + vcc-pc-supply = <®_cldo5>;
> + vcc-pd-supply = <®_swout1>;
> + vcc-pe-supply = <®_bldo1>;
> + vcc-pf-supply = <®_cldo5>;
> + vcc-pg-supply = <®_aldo1>;
> + vcc-ph-supply = <®_swout2>;
> + vcc-pj-supply = <®_swout1>;
> + vcc-pk-supply = <®_bldo1>;
> +};
> +
> +&r_i2c0 {
> + status = "okay";
Should "status" have been last (preceded by a blank line)? (dts-coding-style.rst)
> + pinctrl-names = "default";
> + pinctrl-0 = <&r_i2c0_pl_pins>;
> +
> + axp318w: pmic@36 {
> + compatible = "x-powers,axp318w";
> + reg = <0x36>;
> + interrupt-parent = <&nmi_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + aldo156in-supply = <®_ps>;
> + aldo234in-supply = <®_aldo1>;
> + bldoin-supply = <®_ldo_input>;
> + cldoin-supply = <®_ldo_input>;
> + dldoin-supply = <®_ps>;
> + eldoin-supply = <®_dcdc9>;
> + ips-supply = <®_ps>;
> + vin19-supply = <®_ps>;
> + vin23-supply = <®_ps>;
> + vin45-supply = <®_ps>;
> + vin678-supply = <®_ps>;
> +
> + regulators {
> + reg_dcdc1: dcdc1 {
> + regulator-name = "vcc-3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_dcdc2: dcdc2 {
> + regulator-name = "vdd-sys";
> + regulator-always-on;
> + };
> +
> + reg_dcdc3: dcdc3 {
> + regulator-name = "vdd-cpub";
> + regulator-always-on;
> + };
> +
> + reg_dcdc4: dcdc4 {
> + regulator-name = "vdd-gpu";
> + regulator-always-on;
> + };
> +
> + reg_dcdc5: dcdc5 {
> + regulator-name = "vdd-cpul";
> + regulator-always-on;
> + };
> +
> + reg_dcdc6: dcdc6 {
> + regulator-name = "vcc-draml";
> + regulator-always-on;
> + };
> +
> + reg_dcdc7: dcdc7 {
> + regulator-name = "vcc-dram";
> + regulator-always-on;
> + };
> +
> + reg_dcdc8: dcdc8 {
> + regulator-name = "vcc-ufs-io";
> + regulator-always-on;
> + };
> +
> + reg_dcdc9: dcdc9 {
> + regulator-name = "eldo-input";
> + regulator-always-on;
> + };
> +
> + reg_swout1: swout1 {
> + regulator-name = "vcc33-lcd";
> + regulator-always-on;
> + };
> +
> + reg_swout2: swout2 {
> + regulator-name = "vcc-io-card";
> + regulator-always-on;
> + };
> +
> + reg_aldo1: aldo1 {
> + regulator-name = "vcc-pl";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_bldo1: bldo1 {
> + regulator-name = "vcc-pe-pk-mcsi";
> + };
> +
> + reg_bldo2: bldo2 {
> + regulator-name = "vcc-lvds0";
> + regulator-always-on;
> + };
> +
> + reg_bldo4: bldo4 {
> + regulator-name = "vcc18-codec";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + reg_cldo1: cldo1 {
> + regulator-name = "vcc33-18-usb";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + reg_cldo2: cldo2 {
> + regulator-name = "vcc18-hdmi";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + reg_cldo3: cldo3 {
> + regulator-name = "vcc-pll-dram";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + reg_cldo5: cldo5 {
> + regulator-name = "vcc18-pf-pc";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + reg_dldo1: dldo1 {
> + regulator-name = "vcc-efuse";
> + regulator-always-on;
> + };
> +
> + reg_dldo6: dldo6 {
> + regulator-name = "vcc-ufs";
> + regulator-always-on;
> + };
> +
> + reg_eldo1: eldo1 {
> + regulator-name = "vcc09-vdd2l";
> + regulator-always-on;
> + };
> +
> + reg_eldo6: eldo6 {
> + regulator-name = "vdd-cpus";
> + regulator-always-on;
> + };
> +
> + reg_rtc_ldo: rtc-ldo {
> + regulator-name = "vcc-rtc";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&r_pio {
> + /* PL powers the PMIC bus itself; firmware must keep ALDO1 enabled. */
> + vcc-pm-supply = <®_aldo1>;
> +};
> +
> +&rtc {
> + clocks = <&r_ccu CLK_BUS_R_RTC>, <&osc>, <&r_ccu CLK_R_AHB>,
> + <&osc32k>;
> + clock-names = "bus", "hosc", "ahb", "ext-osc32k";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pb_pins>;
> + status = "okay";
see above...
> +};