Hi everyone,
This oops has been happening with every 2.3 kernel for as long as I've
had this particular machine. 2.2 is rock-solid on this machine, but 2.3
spews these APIC error messages, and eventually locks. Using serial
console, I have captured the errors; they typically happen after 24-48
hours of continuous operation, whereas the APIC error messages comes
every few seconds or so.
The failure mode is one of two: either an NMI watchdog triggers (shown
in the attached messages), or the machine ceases normal processing and
starts spewing APIC error messages to the serial console.
Someone on here once tried messing with /proc/irq/*/smp_affinity; it had
no effect on the crash.
Attached: oops message, ksymoops, .config, and a dump of some status
files in /proc.
-hpa
APIC error interrupt on CPU#0, should never happen.
... APIC ESR0: 00000008
... APIC ESR1: 0000000a
... bit 1: APIC Receive CS Error (hw problem).
... bit 3: APIC Receive Accept Error.
APIC error interrupt on CPU#1, should never happen.
... APIC ESR0: 00000004
... APIC ESR1: 00000004
... bit 2: APIC Send Accept Error.
APIC error interrupt on CPU#1, should never happen.
... APIC ESR0: 00000004
... APIC ESR1: 00000004
... bit 2: APIC Send Accept Error.
APIC error interrupt on CPU#0, should never happen.
... APIC ESR0: 00000002
... APIC ESR1: 00000002
... bit 1: APIC Receive CS Error (hw problem).
NMI Watchdog detected LOCKUP on CPU1, registers:
CPU: 1
EIP: 0010:[<c026dd04>]
EFLAGS: 00003086
eax: f7ee1000 ebx: 00003046 ecx: c223e000 edx: c223ff00
esi: 04000001 edi: 00002710 ebp: 0000000c esp: c223ff0c
ds: 0018 es: 0018 ss: 0018
Process swapper (pid: 0, stackpage=c223f000)
Stack: 000032aa c01bb511 000000f4 00003202 04000001 00000020 00000035 c01bb647
f7a19580 c010da76 0000000c f7ee1000 c223ff7c 00000180 c0347980 0000000c
c223ff74 c010dc69 0000000c c223ff7c f7a19580 c01093c0 c223e000 c01093c0
Call Trace: [<c01bb511>] [<c01bb647>] [<c010da76>] [<c010dc69>] [<c01093c0>] [<c01093c0>] [<c010c26c>]
[<c01093c0>] [<c01093c0>] [<c0100018>] [<c01093ed>] [<c0109432>] [<c021afb7>] [<c01a836e>]
Code: 80 3d 40 89 30 c0 00 f3 90 7e f5 e9 c4 da f4 ff 80 3d 40 89
console shuts up ...
Linux version 2.4.0-test1-ac4 (hpa@tazenda) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 SMP Sat May 27 14:16:19 PDT 2000
BIOS-provided physical RAM map:
e820: 000000000009f000 @ 0000000000000000 (usable)
e820: 0000000000001000 @ 000000000009f000 (reserved)
e820: 0000000000010000 @ 00000000000f0000 (reserved)
e820: 000000003fefd000 @ 0000000000100000 (usable)
e820: 0000000000002000 @ 000000003fffd000 (ACPI data)
e820: 0000000000001000 @ 000000003ffff000 (ACPI NVS)
e820: 0000000000001000 @ 00000000fec00000 (reserved)
e820: 0000000000001000 @ 00000000fee00000 (reserved)
e820: 0000000000010000 @ 00000000ffff0000 (reserved)
127MB HIGHMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at 000f6e80
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
On node 0 totalpages: 262141
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32765 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #1 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
Bootup CPU
Processor #0 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
Bus #0 is PCI
Bus #1 is PCI
Bus #2 is ISA
I/O APIC #2 Version 17 at 0xFEC00000.
Int: type 3, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 00
Int: type 0, pol 0, trig 0, bus 2, IRQ 01, APIC ID 2, APIC INT 01
Int: type 0, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 02
Int: type 0, pol 0, trig 0, bus 2, IRQ 03, APIC ID 2, APIC INT 03
Int: type 0, pol 0, trig 0, bus 2, IRQ 04, APIC ID 2, APIC INT 04
Int: type 0, pol 0, trig 0, bus 2, IRQ 06, APIC ID 2, APIC INT 06
Int: type 0, pol 0, trig 0, bus 2, IRQ 07, APIC ID 2, APIC INT 07
Int: type 0, pol 0, trig 0, bus 2, IRQ 08, APIC ID 2, APIC INT 08
Int: type 0, pol 0, trig 0, bus 2, IRQ 0c, APIC ID 2, APIC INT 0c
Int: type 0, pol 0, trig 0, bus 2, IRQ 0e, APIC ID 2, APIC INT 0e
Int: type 0, pol 0, trig 0, bus 2, IRQ 0f, APIC ID 2, APIC INT 0f
Int: type 0, pol 3, trig 3, bus 1, IRQ 00, APIC ID 2, APIC INT 10
Int: type 0, pol 3, trig 3, bus 0, IRQ 13, APIC ID 2, APIC INT 13
Int: type 0, pol 3, trig 3, bus 0, IRQ 24, APIC ID 2, APIC INT 13
Int: type 0, pol 3, trig 3, bus 0, IRQ 28, APIC ID 2, APIC INT 12
Int: type 0, pol 3, trig 3, bus 0, IRQ 2c, APIC ID 2, APIC INT 11
Int: type 0, pol 3, trig 3, bus 0, IRQ 30, APIC ID 2, APIC INT 10
Lint: type 3, pol 1, trig 1, bus 2, IRQ 00, APIC ID ff, APIC LINT 00
Lint: type 1, pol 1, trig 1, bus 2, IRQ 00, APIC ID ff, APIC LINT 01
Processors: 2
mapped APIC to ffffe000 (fee00000)
mapped IOAPIC to ffffd000 (fec00000)
Enabling extended fast FPU save and restore ... done.
Enabling KNI unmasked exception support ... done.
Kernel command line: BOOT_IMAGE=linux ro root=801 devfs=nomount console=ttyS0,38400 console=tty0 vi
Initializing CPU#0
Detected 651481786 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1300.89 BogoMIPS
Memory: 1027056k/1048564k available (1975k kernel code, 21120k reserved, 182k data, 156k init, 131060k highmem)
Dentry-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
kmem_create: Poisoning requested, but con given - bdev_cache
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
kmem_create: Poisoning requested, but con given - inode_cache
CPU serial number disabled.
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.36 (20000221) Richard Gooch (rgooch@atnf.csiro.au)
CPU serial number disabled.
CPU0: Intel Pentium III (Coppermine) stepping 01
per-CPU timeslice cutoff: 714.46 usecs.
Getting VERSION: 40011
Getting VERSION: 40011
Getting LVT0: 8700
Getting LVT1: 400
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
CPU present map: 3
Booting processor 1/0 eip 2000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Waiting for send to finish...
+Deasserting INIT.
Waiting for send to finish...
+#startup loops: 2.
Sending STARTUP #1.
After apic_write.
Startup point 1.
Initializing CPU#1
Waiting for send to finish...
CPU#1 (phys ID: 0) waiting for CALLOUT
+Sending STARTUP #2.
After apic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 1.
After Callout 1.
CALLIN, before setup_local_APIC().
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1300.89 BogoMIPS
Stack at about c223ffbc
CPU serial number disabled.
OK.
CPU1: Intel Pentium III (Coppermine) stepping 01
CPU has booted.
Before bogomips.
Total of 2 processors activated (2601.78 BogoMIPS).
Before bogocount - setting activated=1.
Boot done.
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 2 ... ok.
Synchronizing Arb IDs.
..TIMER: vector=49 pin1=2 pin2=0
activating NMI Watchdog ... done.
testing the IO APIC.......................
.................................... done.
calibrating APIC timer ...
..... CPU clock speed is 651.4244 MHz.
..... host bus clock speed is 100.2190 MHz.
cpu: 0, clocks: 1002190, slice: 334063
CPU0<C0:1002176,C:668112,D:1,S:334063,C:1002190>
cpu: 1, clocks: 1002190, slice: 334063
CPU1<C0:1002176,C:334048,D:2,S:334063,C:1002190>
checking TSC synchronization across CPUs: passed.
Setting commenced=1, go go go
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs
PCI: PCI BIOS revision 2.10 entry at 0xf0730, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router PIIX [8086/122e] at 00:04.0
PCI->APIC IRQ transform: (B0,I4,P3) -> 19
PCI->APIC IRQ transform: (B0,I9,P0) -> 19
PCI->APIC IRQ transform: (B0,I10,P0) -> 18
PCI->APIC IRQ transform: (B0,I11,P0) -> 17
PCI->APIC IRQ transform: (B0,I12,P0) -> 16
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.3
Based upon Swansea University Computer Society NET3.039
kmem_create: Poisoning requested, but con given - skbuff_head_cache
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 65536 bind 65536)
Initializing RT netlink socket
Starting kswapd v1.6
matroxfb: Matrox unknown G400 (AGP) detected
matroxfb: MTRR's turned on
matroxfb: 640x480x8bpp (virtual: 640x26208)
matroxfb: framebuffer at 0xE2000000, mapped to 0xf8805000, size 16777216
Console: switching to colour frame buffer device 80x30
fb0: MATROX VGA frame buffer device
pty: 512 Unix98 ptys configured
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
hdc: ASUS CD-S400/A, ATAPI CDROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
sym53c8xx: at PCI bus 0, device 11, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c895 detected with Symbios NVRAM
sym53c895-0: rev 0x2 on pci bus 0 device 11 function 0 irq 17
sym53c895-0: Symbios format NVRAM, ID 7, Fast-40, Parity Checking
sym53c895-0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 07/4e/a0/01/00/24
sym53c895-0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 07/4e/80/00/08/24
sym53c895-0: on-chip RAM at 0xde000000
sym53c895-0: resetting, command processing suspended for 2 seconds
sym53c895-0: restart (scsi reset).
sym53c895-0: enabling clock multiplier
sym53c895-0: Downloading SCSI SCRIPTS.
scsi0 : AdvanSys SCSI 3.2M: PCI Ultra 240 CDB: IO B800/F, IRQ 18
scsi1 : sym53c8xx - version 1.5m
scsi : 2 hosts.
Vendor: YAMAHA Model: CRW8424S Rev: 1.0f
Type: CD-ROM ANSI SCSI revision: 02
sym53c895-0: command processing resumed
Vendor: QUANTUM Model: ATLAS IV 18 WLS Rev: 0909
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sda at scsi1, channel 0, id 0, lun 0
Vendor: QUANTUM Model: ATLAS IV 18 WLS Rev: 0909
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sdb at scsi1, channel 0, id 1, lun 0
sym53c895-0-<0,0>: tagged command queue depth set to 8
sym53c895-0-<1,0>: tagged command queue depth set to 8
scsi : detected 2 SCSI disks total.
sym53c895-0-<0,*>: WIDE SCSI (16 bit) enabled.
sym53c895-0-<0,*>: FAST-40 WIDE SCSI 80.0 MB/s (25 ns, offset 31)
SCSI device sda: hdwr sector= 512 bytes. Sectors= 35885168 [17522 MB] [17.5 GB]
Partition check:
sda: sda1 sda2 sda3 sda4
sym53c895-0-<1,*>: WIDE SCSI (16 bit) enabled.
sym53c895-0-<1,*>: FAST-40 WIDE SCSI 80.0 MB/s (25 ns, offset 31)
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 35885168 [17522 MB] [17.5 GB]
sdb: sdb1 sdb2
Serial driver version 4.93 (2000-03-20) with MANY_PORTS SHARE_IRQ DETECT_IRQ SERIAL_PCI enabled
˙ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
ttyS02 at 0x03e8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10c
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.29 $ 2000/03/30 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
eth0: PCI device 8086:1229, 00:D0:B7:1C:D5:EB, IRQ 19.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 721383-008, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
kmem_create: Forcing size word alignment - nfs_fh
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 156k freed
APIC error interrupt on CPU#1, should never happen.
... APIC ESR0: 00000004
... APIC ESR1: 00000004
... bit 2: APIC Send Accept Error.
APIC error interrupt on CPU#0, should never happen.
... APIC ESR0: 00000002
... APIC ESR1: 00000002
... bit 1: APIC Receive CS Error (hw problem).
APIC error interrupt on CPU#1, should never happen.
... APIC ESR0: 00000004
... APIC ESR1: 00000004
... bit 2: APIC Send Accept Error.
APIC error interrupt on CPU#0, should never happen.
... APIC ESR0: 00000002
... APIC ESR1: 00000002
... bit 1: APIC Receive CS Error (hw problem).
APIC error interrupt on CPU#1, should never happen.
... APIC ESR0: 00000004
... APIC ESR1: 00000004
... bit 2: APIC Send Accept Error.
APIC error interrupt on CPU#1, should never happen.
... APIC ESR0: 00000004
... APIC ESR1: 00000006
... bit 1: APIC Receive CS Error (hw problem).
... bit 2: APIC Send Accept Error.
APIC error interrupt on CPU#0, should never happen.
... APIC ESR0: 00000002
... APIC ESR1: 00000002
... bit 1: APIC Receive CS Error (hw problem).
APIC error interrupt on CPU#1, should never happen.
... APIC ESR0: 00000002
... APIC ESR1: 00000006
... bit 1: APIC Receive CS Error (hw problem).
... bit 2: APIC Send Accept Error.
ksymoops 2.3.3 on i686 2.4.0-test1-ac4. Options used
-v kernel/linux-2.4.0-test1-ac4/vmlinux (specified)
-k /proc/ksyms (default)
-l /proc/modules (default)
-o /lib/modules/2.4.0-test1-ac4/ (default)
-m kernel/linux-2.4.0-test1-ac4/System.map (specified)
Warning (map_ksym_to_module): cannot match loaded module es1371 to a unique module object. Trace may not be reliable.
NMI Watchdog detected LOCKUP on CPU1, registers:
CPU: 1
EIP: 0010:[<c026dd04>]
Using defaults from ksymoops -t elf32-i386 -a i386
EFLAGS: 00003086
eax: f7ee1000 ebx: 00003046 ecx: c223e000 edx: c223ff00
esi: 04000001 edi: 00002710 ebp: 0000000c esp: c223ff0c
ds: 0018 es: 0018 ss: 0018
Process swapper (pid: 0, stackpage=c223f000)
Stack: 000032aa c01bb511 000000f4 00003202 04000001 00000020 00000035 c01bb647
f7a19580 c010da76 0000000c f7ee1000 c223ff7c 00000180 c0347980 0000000c
c223ff74 c010dc69 0000000c c223ff7c f7a19580 c01093c0 c223e000 c01093c0
Call Trace: [<c01bb511>] [<c01bb647>] [<c010da76>] [<c010dc69>] [<c01093c0>] [<c01093c0>] [<c010c26c>]
[<c01093c0>] [<c01093c0>] [<c0100018>] [<c01093ed>] [<c0109432>] [<c021afb7>] [<c01a836e>]
Code: 80 3d 40 89 30 c0 00 f3 90 7e f5 e9 c4 da f4 ff 80 3d 40 89
>>EIP; c026dd04 <stext_lock+41d4/aa68> <=====
Trace; c01bb511 <handle_kbd_event+75/18c>
Trace; c01bb647 <keyboard_interrupt+1f/2c>
Trace; c010da76 <handle_IRQ_event+4e/78>
Trace; c010dc69 <do_IRQ+99/ec>
Trace; c01093c0 <default_idle+0/34>
Trace; c01093c0 <default_idle+0/34>
Trace; c010c26c <ret_from_intr+0/20>
Trace; c01093c0 <default_idle+0/34>
Trace; c01093c0 <default_idle+0/34>
Trace; c0100018 <startup_32+18/c7>
Trace; c01093ed <default_idle+2d/34>
Trace; c0109432 <cpu_idle+3e/54>
Trace; c021afb7 <vgacon_cursor+1db/1e4>
Trace; c01a836e <set_cursor+6e/80>
Code; c026dd04 <stext_lock+41d4/aa68>
00000000 <_EIP>:
Code; c026dd04 <stext_lock+41d4/aa68> <=====
0: 80 3d 40 89 30 c0 00 cmpb $0x0,0xc0308940 <=====
Code; c026dd0b <stext_lock+41db/aa68>
7: f3 90 repz nop
Code; c026dd0d <stext_lock+41dd/aa68>
9: 7e f5 jle 0 <_EIP>
Code; c026dd0f <stext_lock+41df/aa68>
b: e9 c4 da f4 ff jmp fff4dad4 <_EIP+0xfff4dad4> c01bb7d8 <aux_write_ack+4/3c>
Code; c026dd14 <stext_lock+41e4/aa68>
10: 80 3d 40 89 00 00 00 cmpb $0x0,0x8940
activating NMI Watchdog ... done.
cpu: 0, clocks: 1002190, slice: 334063
cpu: 1, clocks: 1002190, slice: 334063
1 warning issued. Results may not be reliable.
#
# Automatically generated make config: don't edit
#
CONFIG_X86=y
CONFIG_ISA=y
# CONFIG_SBUS is not set
CONFIG_UID16=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M686 is not set
CONFIG_M686FX=y
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MCRUSOE is not set
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_L1_CACHE_BYTES=32
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_PGE=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_FX=y
# CONFIG_MICROCODE is not set
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_HIGHMEM=y
CONFIG_MTRR=y
CONFIG_SMP=y
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y
#
# General setup
#
CONFIG_NET=y
# CONFIG_VISWS is not set
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
# CONFIG_PCI_NAMES is not set
# CONFIG_MCA is not set
# CONFIG_HOTPLUG is not set
# CONFIG_PCMCIA is not set
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_SYSCTL=y
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
# CONFIG_PM is not set
# CONFIG_ACPI is not set
# CONFIG_APM is not set
#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_FIFO=y
CONFIG_PARPORT_PC_SUPERIO=y
# CONFIG_PARPORT_AMIGA is not set
# CONFIG_PARPORT_MFC3 is not set
# CONFIG_PARPORT_ATARI is not set
# CONFIG_PARPORT_SUNBPP is not set
CONFIG_PARPORT_OTHER=y
CONFIG_PARPORT_1284=y
#
# Plug and Play configuration
#
# CONFIG_PNP is not set
# CONFIG_ISAPNP is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
CONFIG_BLK_DEV_DAC960=y
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_NBD=m
# CONFIG_BLK_DEV_LVM is not set
# CONFIG_BLK_DEV_MD is not set
# CONFIG_MD_LINEAR is not set
# CONFIG_MD_RAID0 is not set
# CONFIG_RAID15_DANGEROUS is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_INITRD=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_NETLINK=y
CONFIG_RTNETLINK=y
CONFIG_NETLINK_DEV=y
# CONFIG_NETFILTER is not set
CONFIG_FILTER=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_IP_ROUTER is not set
CONFIG_NET_IPIP=m
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
CONFIG_IP_ALIAS=y
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
#
# (it is safe to leave these untouched)
#
CONFIG_SKB_LARGE=y
CONFIG_IPV6=m
CONFIG_IPV6_EUI64=y
CONFIG_IPV6_NO_PB=y
# CONFIG_KHTTPD is not set
# CONFIG_ATM is not set
#
#
#
CONFIG_IPX=m
# CONFIG_IPX_INTERN is not set
CONFIG_SPX=m
CONFIG_ATALK=m
# CONFIG_DECNET is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_BRIDGE is not set
# CONFIG_LLC is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set
#
# ATA/IDE/MFM/RLL support
#
CONFIG_IDE=y
#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
# CONFIG_BLK_DEV_IDEDISK_FUJITSU is not set
# CONFIG_BLK_DEV_IDEDISK_IBM is not set
# CONFIG_BLK_DEV_IDEDISK_MAXTOR is not set
# CONFIG_BLK_DEV_IDEDISK_QUANTUM is not set
# CONFIG_BLK_DEV_IDEDISK_SEAGATE is not set
# CONFIG_BLK_DEV_IDEDISK_WD is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=m
CONFIG_BLK_DEV_IDETAPE=m
CONFIG_BLK_DEV_IDEFLOPPY=m
CONFIG_BLK_DEV_IDESCSI=m
#
# IDE chipset support/bugfixes
#
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_IDEPCI_SHARE_IRQ is not set
# CONFIG_BLK_DEV_IDEDMA_PCI is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_IDEDMA_PCI_AUTO is not set
# CONFIG_BLK_DEV_IDEDMA is not set
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_IDEDMA_NEW_DRIVE_LISTINGS is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_AEC62XX_TUNING is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD7409 is not set
# CONFIG_AMD7409_OVERRIDE is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_CMD64X_RAID is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_HPT366_FIP is not set
# CONFIG_HPT366_MODE3 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_PIIX_TUNING is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_PDC202XX_MASTER is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_VIA82CXXX_TUNING is not set
# CONFIG_IDE_CHIPSETS is not set
# CONFIG_IDEDMA_AUTO is not set
# CONFIG_BLK_DEV_IDE_MODES is not set
#
# SCSI support
#
CONFIG_SCSI=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_SD_EXTRA_DEVS=40
CONFIG_CHR_DEV_ST=m
CONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_SR_EXTRA_DEVS=2
CONFIG_CHR_DEV_SG=y
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_DEBUG_QUEUES is not set
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_TCQ_ON_BY_DEFAULT=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=8
CONFIG_AIC7XXX_PROC_STATS=y
CONFIG_AIC7XXX_RESET_DELAY=5
# CONFIG_SCSI_IPS is not set
CONFIG_SCSI_ADVANSYS=y
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
CONFIG_SCSI_BUSLOGIC=y
# CONFIG_SCSI_OMIT_FLASHPOINT is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_NCR53C8XX is not set
CONFIG_SCSI_SYM53C8XX=y
CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS=8
CONFIG_SCSI_NCR53C8XX_MAX_TAGS=32
CONFIG_SCSI_NCR53C8XX_SYNC=40
# CONFIG_SCSI_NCR53C8XX_PROFILE is not set
# CONFIG_SCSI_NCR53C8XX_IOMAPPED is not set
CONFIG_SCSI_NCR53C8XX_PQS_PDS=y
CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT=y
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_DEBUG is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
# CONFIG_I2O_PCI is not set
# CONFIG_I2O_BLOCK is not set
# CONFIG_I2O_LAN is not set
# CONFIG_I2O_SCSI is not set
# CONFIG_I2O_PROC is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
#
# Appletalk devices
#
# CONFIG_APPLETALK is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_ETHERTAP is not set
# CONFIG_NET_SB1000 is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_NET_VENDOR_3COM=y
# CONFIG_EL1 is not set
# CONFIG_EL2 is not set
# CONFIG_ELPLUS is not set
# CONFIG_EL16 is not set
CONFIG_EL3=m
# CONFIG_3C515 is not set
CONFIG_VORTEX=m
# CONFIG_LANCE is not set
CONFIG_NET_VENDOR_SMC=y
# CONFIG_WD80x3 is not set
CONFIG_ULTRA=m
# CONFIG_ULTRA32 is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_CS89x0 is not set
# CONFIG_DE4X5 is not set
CONFIG_TULIP=m
# CONFIG_DGRS is not set
# CONFIG_DM9102 is not set
CONFIG_EEPRO100=y
# CONFIG_EEPRO100_PM is not set
# CONFIG_LNE390 is not set
# CONFIG_NE3210 is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_RTL8129 is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_ES3210 is not set
# CONFIG_EPIC100 is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_YELLOWFIN is not set
# CONFIG_ACENIC is not set
# CONFIG_SK98LIN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
CONFIG_PLIP=m
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPPOE=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
CONFIG_SHAPER=m
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
CONFIG_IRDA=m
#
# IrDA protocols
#
CONFIG_IRLAN=m
CONFIG_IRCOMM=m
# CONFIG_IRDA_ULTRA is not set
CONFIG_IRDA_OPTIONS=y
#
# IrDA options
#
CONFIG_IRDA_CACHE_LAST_LSAP=y
CONFIG_IRDA_FAST_RR=y
# CONFIG_IRDA_DEBUG is not set
CONFIG_IRDA_COMPRESSION=y
#
# IrDA compressors
#
CONFIG_IRDA_DEFLATE=m
#
# Infrared-port device drivers
#
#
# SIR device drivers
#
CONFIG_IRTTY_SIR=m
# CONFIG_IRPORT_SIR is not set
#
# FIR device drivers
#
CONFIG_NSC_FIR=m
CONFIG_WINBOND_FIR=m
# CONFIG_TOSHIBA_FIR is not set
# CONFIG_SMC_IRCC_FIR is not set
#
# Dongle support
#
# CONFIG_DONGLE is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
CONFIG_SERIAL_CONSOLE=y
CONFIG_SERIAL_EXTENDED=y
# CONFIG_SERIAL_MANY_PORTS is not set
CONFIG_SERIAL_SHARE_IRQ=y
CONFIG_SERIAL_DETECT_IRQ=y
# CONFIG_SERIAL_MULTIPORT is not set
# CONFIG_HUB6 is not set
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
CONFIG_ROCKETPORT=m
CONFIG_CYCLADES=m
# CONFIG_CYZ_INTR is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_DIGI is not set
# CONFIG_ESPSERIAL is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_ISI is not set
# CONFIG_SYNCLINK is not set
# CONFIG_N_HDLC is not set
# CONFIG_RISCOM8 is not set
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=512
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set
#
# I2C support
#
# CONFIG_I2C is not set
#
# Mice
#
# CONFIG_BUSMOUSE is not set
CONFIG_MOUSE=y
CONFIG_PSMOUSE=y
# CONFIG_82C710_MOUSE is not set
# CONFIG_PC110_PAD is not set
#
# Joysticks
#
CONFIG_JOYSTICK=m
CONFIG_JOY_ANALOG=m
# CONFIG_JOY_ASSASSIN is not set
CONFIG_JOY_GRAVIS=m
CONFIG_JOY_LOGITECH=m
CONFIG_JOY_SIDEWINDER=m
CONFIG_JOY_THRUSTMASTER=m
# CONFIG_JOY_CREATIVE is not set
CONFIG_JOY_LIGHTNING=m
# CONFIG_JOY_PCI is not set
# CONFIG_JOY_MAGELLAN is not set
# CONFIG_JOY_SPACEORB is not set
# CONFIG_JOY_SPACEBALL is not set
# CONFIG_JOY_WARRIOR is not set
CONFIG_JOY_CONSOLE=m
CONFIG_JOY_DB9=m
CONFIG_JOY_TURBOGRAFX=m
# CONFIG_QIC02_TAPE is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
CONFIG_NVRAM=m
CONFIG_RTC=y
#
# Video For Linux
#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
# CONFIG_DRM is not set
# CONFIG_DRM_TDFX is not set
CONFIG_AGP=m
CONFIG_AGP_INTEL=y
# CONFIG_AGP_I810 is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_ALI is not set
#
# File systems
#
# CONFIG_QUOTA is not set
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
# CONFIG_ADFS_FS is not set
# CONFIG_ADFS_FS_RW is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_BFS_FS is not set
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_UMSDOS_FS=m
CONFIG_VFAT_FS=m
# CONFIG_EFS_FS is not set
CONFIG_CRAMFS=m
CONFIG_RAMFS=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_MINIX_FS=m
# CONFIG_NTFS_FS is not set
# CONFIG_NTFS_RW is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVFS_MOUNT is not set
# CONFIG_DEVFS_DEBUG is not set
CONFIG_DEVPTS_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX4FS_RW is not set
CONFIG_ROMFS_FS=m
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
# CONFIG_SYSV_FS_WRITE is not set
# CONFIG_UDF_FS is not set
# CONFIG_UDF_RW is not set
CONFIG_UFS_FS=m
CONFIG_UFS_FS_WRITE=y
#
# Network File Systems
#
# CONFIG_CODA_FS is not set
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_ROOT_NFS is not set
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
CONFIG_SUNRPC=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_SMB_FS=m
# CONFIG_NCP_FS is not set
# CONFIG_NCPFS_PACKET_SIGNING is not set
# CONFIG_NCPFS_IOCTL_LOCKING is not set
# CONFIG_NCPFS_STRONG is not set
# CONFIG_NCPFS_NFS_NS is not set
# CONFIG_NCPFS_OS2_NS is not set
# CONFIG_NCPFS_SMALLDOS is not set
# CONFIG_NCPFS_MOUNT_SUBDIR is not set
# CONFIG_NCPFS_NDS_DOMAINS is not set
# CONFIG_NCPFS_NLS is not set
# CONFIG_NCPFS_EXTRAS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
CONFIG_VIDEO_SELECT=y
# CONFIG_MDA_CONSOLE is not set
#
# Frame-buffer support
#
CONFIG_FB=y
CONFIG_DUMMY_CONSOLE=y
# CONFIG_FB_RIVA is not set
# CONFIG_FB_CLGEN is not set
# CONFIG_FB_PM2 is not set
CONFIG_FB_VESA=y
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_HGA is not set
CONFIG_VIDEO_SELECT=y
CONFIG_FB_MATROX=y
CONFIG_FB_MATROX_MILLENIUM=y
CONFIG_FB_MATROX_MYSTIQUE=y
CONFIG_FB_MATROX_G100=y
CONFIG_FB_MATROX_MULTIHEAD=y
# CONFIG_FB_ATY is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_3DFX is not set
CONFIG_FB_VIRTUAL=m
# CONFIG_FBCON_ADVANCED is not set
CONFIG_FBCON_MFB=m
CONFIG_FBCON_CFB2=m
CONFIG_FBCON_CFB4=m
CONFIG_FBCON_CFB8=y
CONFIG_FBCON_CFB16=y
CONFIG_FBCON_CFB24=y
CONFIG_FBCON_CFB32=y
CONFIG_FBCON_MAC=m
# CONFIG_FBCON_FONTWIDTH8_ONLY is not set
# CONFIG_FBCON_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
#
# Sound
#
CONFIG_SOUND=m
# CONFIG_SOUND_CMPCI is not set
CONFIG_SOUND_EMU10K1=m
CONFIG_SOUND_ES1370=m
CONFIG_SOUND_ES1371=m
CONFIG_SOUND_ESSSOLO1=m
CONFIG_SOUND_MAESTRO=m
CONFIG_SOUND_SONICVIBES=m
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
CONFIG_SOUND_OSS=m
# CONFIG_SOUND_TRACEINIT is not set
# CONFIG_SOUND_DMAP is not set
# CONFIG_SOUND_AD1816 is not set
# CONFIG_SOUND_SGALAXY is not set
CONFIG_SOUND_ADLIB=m
# CONFIG_SOUND_ACI_MIXER is not set
CONFIG_SOUND_CS4232=m
# CONFIG_SOUND_SSCAPE is not set
CONFIG_SOUND_GUS=m
# CONFIG_SOUND_GUS16 is not set
# CONFIG_SOUND_GUSMAX is not set
# CONFIG_SOUND_ICH is not set
CONFIG_SOUND_VMIDI=m
# CONFIG_SOUND_TRIX is not set
CONFIG_SOUND_MSS=m
CONFIG_SOUND_MPU401=m
# CONFIG_SOUND_NM256 is not set
# CONFIG_SOUND_MAD16 is not set
CONFIG_SOUND_PAS=m
# CONFIG_PAS_JOYSTICK is not set
CONFIG_SOUND_PSS=m
CONFIG_PSS_MIXER=y
# CONFIG_PSS_HAVE_BOOT is not set
CONFIG_SOUND_SOFTOSS=m
CONFIG_SOUND_SB=m
CONFIG_SOUND_AWE32_SYNTH=m
CONFIG_SOUND_WAVEFRONT=m
CONFIG_SOUND_MAUI=m
CONFIG_SOUND_YM3812=m
CONFIG_SOUND_OPL3SA1=m
CONFIG_SOUND_OPL3SA2=m
# CONFIG_SOUND_UART6850 is not set
# CONFIG_SOUND_AEDSP16 is not set
#
# USB support
#
# CONFIG_USB is not set
#
# Kernel hacking
#
CONFIG_MAGIC_SYSRQ=y
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Wed May 31 2000 - 21:00:20 EST