On Sat, Jun 15, 2002 at 03:36:06PM +0200, Kurt Garloff wrote:
> Life would be easier if the scsi subsystem would just report which SCSI
> device (uniquely identified by the controller,bus,target,unit tuple) belongs
> to which high-level device. The information is available in the kernel.
I prefer we refer to the tuple as host, channel, id, lun (H, C, I, L), so
as to more closely match /proc/scsi/scsi, /proc/scsi/sg, and attached
messages:
[root@elm3a50 root]# cat /proc/scsi/scsi | head -4
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: IBM-PSG Model: ST318203LC !# Rev: B222
Type: Direct-Access ANSI SCSI revision: 02
root # cat /proc/scsi/sg/device_hdr /proc/scsi/sg/devices | head -2
host chan id lun type opens qdepth busy online
0 0 0 0 0 4 253 0 1
Attached messages are of the form:
Attached scsi disk sdn at scsi2, channel 0, id 2, lun 0
> Attached patch does this:
> garloff@pckurt:/raid5/Kernel/src $ cat /proc/scsi/map
> # C,B,T,U Type onl sg_nm sg_dev nm dev(hex)
> 0,0,00,00 0x05 1 sg0 c:15:00 sr0 b:0b:00
> 1,0,01,00 0x05 1 sg1 c:15:01 sr1 b:0b:01
> 1,0,02,00 0x01 1 sg2 c:15:02 osst0 c:ce:00
> 1,0,03,00 0x05 1 sg3 c:15:03 sr2 b:0b:02
> 1,0,05,00 0x00 1 sg4 c:15:04 sda b:08:00
> 1,0,09,00 0x00 1 sg5 c:15:05 sdb b:08:10
> 2,0,01,00 0x05 1 sg6 c:15:06 sr3 b:0b:03
> 2,0,02,00 0x01 1 sg7 c:15:07 osst1 c:ce:01
> 2,0,03,00 0x05 1 sg8 c:15:08 sr4 b:0b:04
> 2,0,05,00 0x00 1 sg9 c:15:09 sdc b:08:20
> 2,0,09,00 0x00 1 sg10 c:15:0a sdd b:08:30
> 3,0,10,00 0x00 1 sg11 c:15:0b sde b:08:40
> 3,0,12,00 0x00 1 sg12 c:15:0c sdf b:08:50
Why not treat each upper layer driver the same? Type is already
in /proc/scsi/scsi, or implied by the upper level drivers attached.
Online should really be part of /proc/scsi/scsi.
Then, each line is a path followed by a list of upper level devices.
This would also simplify the code, although the ordering of the upper
level devices becomes link or module load order dependent.
And similiar to sg (someone commented on parsing '^#'), have a _hdr
entry; something like:
$ cat /proc/scsi/map_hdr /proc/scsi/map
H:C:I:L online type:name:block/char:maj:min
00:00:00:00 1 sg:sg0:c:15:00 sr:sr0:b:0b:00
01:00:01:00 1 sg:sg1:c:15:01 sr:sr1:b:0b:01
01:00:02:00 1 sg:sg2:c:15:02 osst:osst0:c:ce:00
02:00:09:00 1 sg:sg3:c:15:03 sd:sdd:b:08:30
Or:
H:C:I:L online type:enumeration:block/char:maj:min
00:00:00:00 1 sg:0:c:15:00 sr:0:b:0b:00
01:00:01:00 1 sg:1:c:15:01 sr:1:b:0b:01
01:00:02:00 1 sg:2:c:15:02 osst:0:c:ce:00
02:00:09:00 1 sg:3:c:15:03 sd:d:b:08:30
> A patch for 2.5 should be done as well, if the design is OK, of course.
>
IMO, we should use driverfs for this in 2.5. Mike Sullivan's scsi driverfs
patch currently ends up with a driverfs layout (showing one Scsi_Device
with two partitions, sg and sd attached) like this:
[root@elm3a50 devices]# tree ./root/pci1/01\:06.0/scsi2/2\:0\:2\:0/
./root/pci1/01:06.0/scsi2/2:0:2:0/
|-- 2:0:2:0:disc
| |-- kdev
| |-- name
| |-- power
| `-- type
|-- 2:0:2:0:gen
| |-- kdev
| |-- name
| |-- power
| `-- type
|-- 2:0:2:0:p1
| |-- kdev
| |-- name
| |-- power
| `-- type
|-- 2:0:2:0:p2
| |-- kdev
| |-- name
| |-- power
| `-- type
|-- name
|-- power
`-- type
Right now, the name is storing an ID; the ID is retrieved in the kernel (using
page 0x80 or page 0x83 or the path). For example disc has:
[root@elm3a50 2:0:2:0:disc]# pwd
/devices/root/pci1/01:06.0/scsi2/2:0:2:0/2:0:2:0:disc
[root@elm3a50 2:0:2:0:disc]# ls
kdev name power type
[root@elm3a50 2:0:2:0:disc]# cat *
8d0
U20000020371719e8disc
0
BLK
-- Patrick Mansfield
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sun Jun 23 2002 - 22:00:14 EST