Bridge changes and lost console on 2.6.13-rc3
From: Jon Smirl
Date: Wed Jul 13 2005 - 12:01:16 EST
During the boot process I lose my console. When X starts it is recoved.
boot log .....
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: d000-dfff
MEM window: fe900000-feafffff
PREFETCH window: f0000000-f7ffffff
>> console stops drawing here
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: fe700000-fe8fffff
PREFETCH window: f8000000-fc0fffff
My machine has two child buses, AGP and PCI. I am using a PCI video
card at 02:03.0. Only the card on bus #2 fails, the AGP card is ok.
Are you setting the VGA port forwarding bits correctly on the bridge
#2 if it is the active display device?
00:00.0 Host bridge: Intel Corp. 82875P/E7210 Memory Controller Hub (rev 02)
Subsystem: Dell: Unknown device 0162
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Capabilities: [e4] Vendor Specific Information
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corp. 82875P Processor to AGP Controller
(rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe900000-feafffff
Prefetchable memory behind bridge: f0000000-f7ffffff
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
00:1d.0 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI
Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell: Unknown device 0162
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 193
Region 4: I/O ports at ff80 [size=32]
00:1d.1 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI
Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell: Unknown device 0162
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 201
Region 4: I/O ports at ff60 [size=32]
00:1d.2 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI
#3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell: Unknown device 0162
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 169
Region 4: I/O ports at ff40 [size=32]
00:1d.3 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI
Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell: Unknown device 0162
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 193
Region 4: I/O ports at ff20 [size=32]
00:1d.7 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI
Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell: Unknown device 0162
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 185
Region 0: Memory at ffa80800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fe700000-fe8fffff
Prefetchable memory behind bridge: f8000000-fc0fffff
Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Interface
Bridge (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801EB/ER (ICH5/ICH5R) IDE
Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Dell: Unknown device 0162
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 169
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at ffa0 [size=16]
Region 5: Memory at febffc00 (32-bit, non-prefetchable) [size=1K]
00:1f.2 IDE interface: Intel Corp. 82801EB (ICH5) SATA Controller (rev
02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Dell: Unknown device 0162
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 169
Region 0: I/O ports at fe00 [size=8]
Region 1: I/O ports at fe10 [size=4]
Region 2: I/O ports at fe20 [size=8]
Region 3: I/O ports at fe30 [size=4]
Region 4: I/O ports at fea0 [size=16]
00:1f.3 SMBus: Intel Corp. 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
Subsystem: Dell: Unknown device 0162
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at efe0 [size=32]
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV250
If [Radeon 9000] (rev 01) (prog-if 00 [VGA])
Subsystem: C.P. Technology Co. Ltd RV250 If [Radeon 9000 Pro "Evil Commando"]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4000000 (32-bit, prefetchable) [disabled] [size=64M]
Region 1: I/O ports at de00 [disabled] [size=256]
Region 2: Memory at fe9e0000 (32-bit, non-prefetchable) [disabled] [size=64K]
Expansion ROM at fe900000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.1 Display controller: ATI Technologies Inc Radeon RV250 [Radeon
9000] (Secondary) (rev 01)
Subsystem: C.P. Technology Co. Ltd: Unknown device 2038
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size 10
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:01.0 Network controller: Intersil Corporation Prism 2.5 Wavelan
chipset (rev 01)
Subsystem: Netgear MA311 802.11b wireless adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 10
Interrupt: pin A routed to IRQ 177
Region 0: Memory at fc000000 (32-bit, prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:02.0 FireWire (IEEE 1394): Texas Instruments TSB12LV23 IEEE-1394
Controller (prog-if 10 [OHCI])
Subsystem: Ads Technologies Inc: Unknown device 0000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 1000ns max), Cache Line Size 10
Interrupt: pin A routed to IRQ 209
Region 0: Memory at fe7d7800 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fe7d8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:03.0 VGA compatible controller: ATI Technologies Inc Rage 128
PD/PRO TMDS (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Rage 128 AIW
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at ce00 [size=256]
Region 2: Memory at fe7dc000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at fc020000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0c.0 Ethernet controller: Intel Corp. 82540EM Gigabit Ethernet
Controller (rev 02)
Subsystem: Dell: Unknown device 0156
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 169
Region 0: Memory at fe7e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at cdc0 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=2, DMOST=0, DMCRS=1, RSCEM-
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
--
Jon Smirl
jonsmirl@xxxxxxxxx
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/