[git patches] net driver fixes (50% rebased)
From: Jeff Garzik
Date: Sun Feb 24 2008 - 00:21:03 EST
This is a 50% resend, rebased on top of net-2.6.
Please pull from 'upstream-davem' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6.git upstream-davem
to receive the following updates:
MAINTAINERS | 11 +-
drivers/net/cs89x0.c | 12 +-
drivers/net/e1000e/82571.c | 22 +--
drivers/net/e1000e/defines.h | 10 +-
drivers/net/e1000e/e1000.h | 3 +-
drivers/net/e1000e/hw.h | 4 +-
drivers/net/e1000e/ich8lan.c | 24 ++--
drivers/net/e1000e/lib.c | 50 ++-----
drivers/net/e1000e/netdev.c | 18 ++--
drivers/net/e1000e/phy.c | 10 +-
drivers/net/ehea/ehea.h | 34 +++++-
drivers/net/ehea/ehea_main.c | 281 +++++++++++++++++++++++++++++++++---
drivers/net/fs_enet/fs_enet-main.c | 7 +-
drivers/net/gianfar.c | 14 +-
drivers/net/igb/igb_main.c | 15 +--
drivers/net/ixgb/ixgb_ethtool.c | 1 +
drivers/net/macb.c | 2 +-
drivers/net/pcmcia/pcnet_cs.c | 10 +-
drivers/net/phy/mdio_bus.c | 4 +-
drivers/net/sis190.c | 15 ++-
drivers/net/sky2.c | 123 ++++++++--------
drivers/net/sky2.h | 27 ++--
drivers/net/tlan.c | 64 ++++----
drivers/net/tulip/uli526x.c | 12 ++-
drivers/net/via-rhine.c | 2 +-
drivers/net/virtio_net.c | 2 +-
drivers/s390/net/claw.c | 39 +++---
27 files changed, 531 insertions(+), 285 deletions(-)
Adrian Bunk (1):
net/phy/mdio_bus.c: fix a check-after-use
Andy Gospodarek (1):
igb: fix legacy mode irq issue
Atsushi Nemoto (1):
macb: Fix speed setting
Auke Kok (4):
ixgb: add RNBC counter - no buffer count - to ethtool stats
e1000e: 82573 can use eerd method to read eeprom
e1000e: fix spelling errors in comments
e1000e: remove unused read value in ASPM disable code.
Becky Bruce (1):
gianfar: don't pass NULL dev ptr to DMA ops
Bill Hayes (1):
igb: Fix panic with NICs with 1000BASE-SX PHY
Christian Borntraeger (1):
virtio_net: Fix oops on early interrupts - introduced by virtio reset code
Francois Romieu (1):
sis190: read the mac address from the eeprom first
Grant Grundler (2):
update TULIP MAINTAINERS
uli526x partially recognizing interface
Harvey Harrison (1):
tlan: add static to function definitions
Jesse Brandeburg (3):
e1000e: fix link up message to show ethX:
e1000e: fix flow control when using ethtool overrides
e1000e: fix flow control denial of service possibility
Julia Lawall (1):
claw: make use of DIV_ROUND_UP
Komuro (1):
pcnet_cs: if AX88190-based card, printk "use axnet_cs instead" message.
Laura Garcia (1):
[netdrvr] via-rhine: Use register offset definition for WOLcgClr
Leonardo Potenza (1):
drivers/net/cs89x0.c: compilation warning fix
Scott Wood (1):
fs_enet: Don't call phy_mii_ioctl() in atomic context.
Stephen Hemminger (1):
sky2: fix LED management
Thomas Klein (1):
ehea: add kdump support
diff --git a/MAINTAINERS b/MAINTAINERS
index 36c7bc6..2333255 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3884,10 +3884,13 @@ M: trivial@xxxxxxxxxx
L: linux-kernel@xxxxxxxxxxxxxxx
S: Maintained
-TULIP NETWORK DRIVER
-L: tulip-users@xxxxxxxxxxxxxxxxxxxxx
-W: http://sourceforge.net/projects/tulip/
-S: Orphan
+TULIP NETWORK DRIVERS
+P: Grant Grundler
+M: grundler@xxxxxxxxxxxxxxxx
+P: Kyle McMartin
+M: kyle@xxxxxxxxxxxxxxxx
+L: netdev@xxxxxxxxxxxxxxx
+S: Maintained
TUN/TAP driver
P: Maxim Krasnyansky
diff --git a/drivers/net/cs89x0.c b/drivers/net/cs89x0.c
index 5717509..348371f 100644
--- a/drivers/net/cs89x0.c
+++ b/drivers/net/cs89x0.c
@@ -172,30 +172,30 @@ static char version[] __initdata =
them to system IRQ numbers. This mapping is card specific and is set to
the configuration of the Cirrus Eval board for this chip. */
#ifdef CONFIG_ARCH_CLPS7500
-static unsigned int netcard_portlist[] __initdata =
+static unsigned int netcard_portlist[] __used __initdata =
{ 0x80090303, 0x300, 0x320, 0x340, 0x360, 0x200, 0x220, 0x240, 0x260, 0x280, 0x2a0, 0x2c0, 0x2e0, 0};
static unsigned int cs8900_irq_map[] = {12,0,0,0};
#elif defined(CONFIG_SH_HICOSH4)
-static unsigned int netcard_portlist[] __initdata =
+static unsigned int netcard_portlist[] __used __initdata =
{ 0x0300, 0};
static unsigned int cs8900_irq_map[] = {1,0,0,0};
#elif defined(CONFIG_MACH_IXDP2351)
-static unsigned int netcard_portlist[] __initdata = {IXDP2351_VIRT_CS8900_BASE, 0};
+static unsigned int netcard_portlist[] __used __initdata = {IXDP2351_VIRT_CS8900_BASE, 0};
static unsigned int cs8900_irq_map[] = {IRQ_IXDP2351_CS8900, 0, 0, 0};
#include <asm/irq.h>
#elif defined(CONFIG_ARCH_IXDP2X01)
#include <asm/irq.h>
-static unsigned int netcard_portlist[] __initdata = {IXDP2X01_CS8900_VIRT_BASE, 0};
+static unsigned int netcard_portlist[] __used __initdata = {IXDP2X01_CS8900_VIRT_BASE, 0};
static unsigned int cs8900_irq_map[] = {IRQ_IXDP2X01_CS8900, 0, 0, 0};
#elif defined(CONFIG_ARCH_PNX010X)
#include <asm/irq.h>
#include <asm/arch/gpio.h>
#define CIRRUS_DEFAULT_BASE IO_ADDRESS(EXT_STATIC2_s0_BASE + 0x200000) /* = Physical address 0x48200000 */
#define CIRRUS_DEFAULT_IRQ VH_INTC_INT_NUM_CASCADED_INTERRUPT_1 /* Event inputs bank 1 - ID 35/bit 3 */
-static unsigned int netcard_portlist[] __initdata = {CIRRUS_DEFAULT_BASE, 0};
+static unsigned int netcard_portlist[] __used __initdata = {CIRRUS_DEFAULT_BASE, 0};
static unsigned int cs8900_irq_map[] = {CIRRUS_DEFAULT_IRQ, 0, 0, 0};
#else
-static unsigned int netcard_portlist[] __initdata =
+static unsigned int netcard_portlist[] __used __initdata =
{ 0x300, 0x320, 0x340, 0x360, 0x200, 0x220, 0x240, 0x260, 0x280, 0x2a0, 0x2c0, 0x2e0, 0};
static unsigned int cs8900_irq_map[] = {10,11,12,5};
#endif
diff --git a/drivers/net/e1000e/82571.c b/drivers/net/e1000e/82571.c
index 3beace5..7fe2031 100644
--- a/drivers/net/e1000e/82571.c
+++ b/drivers/net/e1000e/82571.c
@@ -438,7 +438,7 @@ static void e1000_release_nvm_82571(struct e1000_hw *hw)
* For non-82573 silicon, write data to EEPROM at offset using SPI interface.
*
* If e1000e_update_nvm_checksum is not called after this function, the
- * EEPROM will most likley contain an invalid checksum.
+ * EEPROM will most likely contain an invalid checksum.
**/
static s32 e1000_write_nvm_82571(struct e1000_hw *hw, u16 offset, u16 words,
u16 *data)
@@ -547,7 +547,7 @@ static s32 e1000_validate_nvm_checksum_82571(struct e1000_hw *hw)
* poll for completion.
*
* If e1000e_update_nvm_checksum is not called after this function, the
- * EEPROM will most likley contain an invalid checksum.
+ * EEPROM will most likely contain an invalid checksum.
**/
static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
u16 words, u16 *data)
@@ -1053,7 +1053,7 @@ static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw)
/* If SerDes loopback mode is entered, there is no form
* of reset to take the adapter out of that mode. So we
* have to explicitly take the adapter out of loopback
- * mode. This prevents drivers from twidling their thumbs
+ * mode. This prevents drivers from twiddling their thumbs
* if another tool failed to take it out of loopback mode.
*/
ew32(SCTL,
@@ -1098,7 +1098,7 @@ static s32 e1000_valid_led_default_82571(struct e1000_hw *hw, u16 *data)
* e1000e_get_laa_state_82571 - Get locally administered address state
* @hw: pointer to the HW structure
*
- * Retrieve and return the current locally administed address state.
+ * Retrieve and return the current locally administered address state.
**/
bool e1000e_get_laa_state_82571(struct e1000_hw *hw)
{
@@ -1113,7 +1113,7 @@ bool e1000e_get_laa_state_82571(struct e1000_hw *hw)
* @hw: pointer to the HW structure
* @state: enable/disable locally administered address
*
- * Enable/Disable the current locally administed address state.
+ * Enable/Disable the current locally administers address state.
**/
void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state)
{
@@ -1281,16 +1281,6 @@ static struct e1000_phy_operations e82_phy_ops_m88 = {
static struct e1000_nvm_operations e82571_nvm_ops = {
.acquire_nvm = e1000_acquire_nvm_82571,
- .read_nvm = e1000e_read_nvm_spi,
- .release_nvm = e1000_release_nvm_82571,
- .update_nvm = e1000_update_nvm_checksum_82571,
- .valid_led_default = e1000_valid_led_default_82571,
- .validate_nvm = e1000_validate_nvm_checksum_82571,
- .write_nvm = e1000_write_nvm_82571,
-};
-
-static struct e1000_nvm_operations e82573_nvm_ops = {
- .acquire_nvm = e1000_acquire_nvm_82571,
.read_nvm = e1000e_read_nvm_eerd,
.release_nvm = e1000_release_nvm_82571,
.update_nvm = e1000_update_nvm_checksum_82571,
@@ -1355,6 +1345,6 @@ struct e1000_info e1000_82573_info = {
.get_invariants = e1000_get_invariants_82571,
.mac_ops = &e82571_mac_ops,
.phy_ops = &e82_phy_ops_m88,
- .nvm_ops = &e82573_nvm_ops,
+ .nvm_ops = &e82571_nvm_ops,
};
diff --git a/drivers/net/e1000e/defines.h b/drivers/net/e1000e/defines.h
index 6232c3e..a4f511f 100644
--- a/drivers/net/e1000e/defines.h
+++ b/drivers/net/e1000e/defines.h
@@ -66,7 +66,7 @@
#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
/* Extended Device Control */
-#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */
+#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */
#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
@@ -75,12 +75,12 @@
#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */
#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */
-/* Receive Decriptor bit definitions */
+/* Receive Descriptor bit definitions */
#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
-#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum caculated */
+#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
@@ -223,7 +223,7 @@
#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion by NVM */
#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
-/* Constants used to intrepret the masked PCI-X bus speed. */
+/* Constants used to interpret the masked PCI-X bus speed. */
#define HALF_DUPLEX 1
#define FULL_DUPLEX 2
@@ -517,7 +517,7 @@
/* PHY 1000 MII Register/Bit Definitions */
/* PHY Registers defined by IEEE */
#define PHY_CONTROL 0x00 /* Control Register */
-#define PHY_STATUS 0x01 /* Status Regiser */
+#define PHY_STATUS 0x01 /* Status Register */
#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h
index 8b88c22..327c062 100644
--- a/drivers/net/e1000e/e1000.h
+++ b/drivers/net/e1000e/e1000.h
@@ -42,8 +42,7 @@
struct e1000_info;
#define ndev_printk(level, netdev, format, arg...) \
- printk(level "%s: %s: " format, (netdev)->dev.parent->bus_id, \
- (netdev)->name, ## arg)
+ printk(level "%s: " format, (netdev)->name, ## arg)
#ifdef DEBUG
#define ndev_dbg(netdev, format, arg...) \
diff --git a/drivers/net/e1000e/hw.h b/drivers/net/e1000e/hw.h
index 3c5862f..916025b 100644
--- a/drivers/net/e1000e/hw.h
+++ b/drivers/net/e1000e/hw.h
@@ -184,7 +184,7 @@ enum e1e_registers {
E1000_ICRXDMTC = 0x04120, /* Irq Cause Rx Desc MinThreshold Count */
E1000_ICRXOC = 0x04124, /* Irq Cause Receiver Overrun Count */
E1000_RXCSUM = 0x05000, /* RX Checksum Control - RW */
- E1000_RFCTL = 0x05008, /* Receive Filter Control*/
+ E1000_RFCTL = 0x05008, /* Receive Filter Control */
E1000_MTA = 0x05200, /* Multicast Table Array - RW Array */
E1000_RA = 0x05400, /* Receive Address - RW Array */
E1000_VFTA = 0x05600, /* VLAN Filter Table Array - RW Array */
@@ -202,7 +202,7 @@ enum e1e_registers {
E1000_FACTPS = 0x05B30, /* Function Active and Power State to MNG */
E1000_SWSM = 0x05B50, /* SW Semaphore */
E1000_FWSM = 0x05B54, /* FW Semaphore */
- E1000_HICR = 0x08F00, /* Host Inteface Control */
+ E1000_HICR = 0x08F00, /* Host Interface Control */
};
/* RSS registers */
diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c
index 8f8139d..0ae3955 100644
--- a/drivers/net/e1000e/ich8lan.c
+++ b/drivers/net/e1000e/ich8lan.c
@@ -671,7 +671,7 @@ static s32 e1000_get_phy_info_ich8lan(struct e1000_hw *hw)
* e1000_check_polarity_ife_ich8lan - Check cable polarity for IFE PHY
* @hw: pointer to the HW structure
*
- * Polarity is determined on the polarity reveral feature being enabled.
+ * Polarity is determined on the polarity reversal feature being enabled.
* This function is only called by other family-specific
* routines.
**/
@@ -947,7 +947,7 @@ static s32 e1000_flash_cycle_init_ich8lan(struct e1000_hw *hw)
/* Either we should have a hardware SPI cycle in progress
* bit to check against, in order to start a new cycle or
* FDONE bit should be changed in the hardware so that it
- * is 1 after harware reset, which can then be used as an
+ * is 1 after hardware reset, which can then be used as an
* indication whether a cycle is in progress or has been
* completed.
*/
@@ -1155,7 +1155,7 @@ static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
* which writes the checksum to the shadow ram. The changes in the shadow
* ram are then committed to the EEPROM by processing each bank at a time
* checking for the modified bit and writing only the pending changes.
- * After a succesful commit, the shadow ram is cleared and is ready for
+ * After a successful commit, the shadow ram is cleared and is ready for
* future writes.
**/
static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
@@ -1680,7 +1680,7 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
* - initialize LED identification
* - setup receive address registers
* - setup flow control
- * - setup transmit discriptors
+ * - setup transmit descriptors
* - clear statistics
**/
static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw)
@@ -1961,7 +1961,7 @@ static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw)
E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
ew32(PHY_CTRL, phy_ctrl);
- /* Call gig speed drop workaround on Giga disable before accessing
+ /* Call gig speed drop workaround on Gig disable before accessing
* any PHY registers */
e1000e_gig_downshift_workaround_ich8lan(hw);
@@ -1972,7 +1972,7 @@ static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw)
/**
* e1000_set_kmrn_lock_loss_workaound_ich8lan - Set Kumeran workaround state
* @hw: pointer to the HW structure
- * @state: boolean value used to set the current Kumaran workaround state
+ * @state: boolean value used to set the current Kumeran workaround state
*
* If ICH8, set the current Kumeran workaround state (enabled - TRUE
* /disabled - FALSE).
@@ -2017,7 +2017,7 @@ void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw)
E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
ew32(PHY_CTRL, reg);
- /* Call gig speed drop workaround on Giga disable before
+ /* Call gig speed drop workaround on Gig disable before
* accessing any PHY registers */
if (hw->mac.type == e1000_ich8lan)
e1000e_gig_downshift_workaround_ich8lan(hw);
@@ -2045,7 +2045,7 @@ void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw)
* @hw: pointer to the HW structure
*
* Steps to take when dropping from 1Gb/s (eg. link cable removal (LSC),
- * LPLU, Giga disable, MDIC PHY reset):
+ * LPLU, Gig disable, MDIC PHY reset):
* 1) Set Kumeran Near-end loopback
* 2) Clear Kumeran Near-end loopback
* Should only be called for ICH8[m] devices with IGP_3 Phy.
@@ -2089,10 +2089,10 @@ static s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw)
}
/**
- * e1000_led_on_ich8lan - Turn LED's on
+ * e1000_led_on_ich8lan - Turn LEDs on
* @hw: pointer to the HW structure
*
- * Turn on the LED's.
+ * Turn on the LEDs.
**/
static s32 e1000_led_on_ich8lan(struct e1000_hw *hw)
{
@@ -2105,10 +2105,10 @@ static s32 e1000_led_on_ich8lan(struct e1000_hw *hw)
}
/**
- * e1000_led_off_ich8lan - Turn LED's off
+ * e1000_led_off_ich8lan - Turn LEDs off
* @hw: pointer to the HW structure
*
- * Turn off the LED's.
+ * Turn off the LEDs.
**/
static s32 e1000_led_off_ich8lan(struct e1000_hw *hw)
{
diff --git a/drivers/net/e1000e/lib.c b/drivers/net/e1000e/lib.c
index 16f35fa..95f75a4 100644
--- a/drivers/net/e1000e/lib.c
+++ b/drivers/net/e1000e/lib.c
@@ -589,9 +589,6 @@ static s32 e1000_set_default_fc_generic(struct e1000_hw *hw)
s32 ret_val;
u16 nvm_data;
- if (mac->fc != e1000_fc_default)
- return 0;
-
/* Read and store word 0x0F of the EEPROM. This word contains bits
* that determine the hardware's default PAUSE (flow control) mode,
* a bit that determines whether the HW defaults to enabling or
@@ -1107,34 +1104,13 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
(mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
mac->fc = e1000_fc_rx_pause;
hw_dbg(hw, "Flow Control = RX PAUSE frames only.\r\n");
- }
- /* Per the IEEE spec, at this point flow control should be
- * disabled. However, we want to consider that we could
- * be connected to a legacy switch that doesn't advertise
- * desired flow control, but can be forced on the link
- * partner. So if we advertised no flow control, that is
- * what we will resolve to. If we advertised some kind of
- * receive capability (Rx Pause Only or Full Flow Control)
- * and the link partner advertised none, we will configure
- * ourselves to enable Rx Flow Control only. We can do
- * this safely for two reasons: If the link partner really
- * didn't want flow control enabled, and we enable Rx, no
- * harm done since we won't be receiving any PAUSE frames
- * anyway. If the intent on the link partner was to have
- * flow control enabled, then by us enabling RX only, we
- * can at least receive pause frames and process them.
- * This is a good idea because in most cases, since we are
- * predominantly a server NIC, more times than not we will
- * be asked to delay transmission of packets than asking
- * our link partner to pause transmission of frames.
- */
- else if ((mac->original_fc == e1000_fc_none) ||
- (mac->original_fc == e1000_fc_tx_pause)) {
+ } else {
+ /*
+ * Per the IEEE spec, at this point flow control
+ * should be disabled.
+ */
mac->fc = e1000_fc_none;
hw_dbg(hw, "Flow Control = NONE.\r\n");
- } else {
- mac->fc = e1000_fc_rx_pause;
- hw_dbg(hw, "Flow Control = RX PAUSE frames only.\r\n");
}
/* Now we need to do one last check... If we auto-
@@ -1164,7 +1140,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
}
/**
- * e1000e_get_speed_and_duplex_copper - Retreive current speed/duplex
+ * e1000e_get_speed_and_duplex_copper - Retrieve current speed/duplex
* @hw: pointer to the HW structure
* @speed: stores the current speed
* @duplex: stores the current duplex
@@ -1200,7 +1176,7 @@ s32 e1000e_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed, u16 *dup
}
/**
- * e1000e_get_speed_and_duplex_fiber_serdes - Retreive current speed/duplex
+ * e1000e_get_speed_and_duplex_fiber_serdes - Retrieve current speed/duplex
* @hw: pointer to the HW structure
* @speed: stores the current speed
* @duplex: stores the current duplex
@@ -1410,7 +1386,7 @@ s32 e1000e_cleanup_led_generic(struct e1000_hw *hw)
* e1000e_blink_led - Blink LED
* @hw: pointer to the HW structure
*
- * Blink the led's which are set to be on.
+ * Blink the LEDs which are set to be on.
**/
s32 e1000e_blink_led(struct e1000_hw *hw)
{
@@ -1515,7 +1491,7 @@ void e1000e_set_pcie_no_snoop(struct e1000_hw *hw, u32 no_snoop)
* @hw: pointer to the HW structure
*
* Returns 0 if successful, else returns -10
- * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not casued
+ * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused
* the master requests to be disabled.
*
* Disables PCI-Express master access and verifies there are no pending
@@ -1876,7 +1852,7 @@ static s32 e1000_ready_nvm_eeprom(struct e1000_hw *hw)
}
/**
- * e1000e_read_nvm_spi - Read EEPROM's using SPI
+ * e1000e_read_nvm_spi - Reads EEPROM using SPI
* @hw: pointer to the HW structure
* @offset: offset of word in the EEPROM to read
* @words: number of words to read
@@ -1980,7 +1956,7 @@ s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
* Writes data to EEPROM at offset using SPI interface.
*
* If e1000e_update_nvm_checksum is not called after this function , the
- * EEPROM will most likley contain an invalid checksum.
+ * EEPROM will most likely contain an invalid checksum.
**/
s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
{
@@ -2222,7 +2198,7 @@ static u8 e1000_calculate_checksum(u8 *buffer, u32 length)
*
* Returns E1000_success upon success, else E1000_ERR_HOST_INTERFACE_COMMAND
*
- * This function checks whether the HOST IF is enabled for command operaton
+ * This function checks whether the HOST IF is enabled for command operation
* and also checks whether the previous command is completed. It busy waits
* in case of previous command is not completed.
**/
@@ -2254,7 +2230,7 @@ static s32 e1000_mng_enable_host_if(struct e1000_hw *hw)
}
/**
- * e1000e_check_mng_mode - check managament mode
+ * e1000e_check_mng_mode - check management mode
* @hw: pointer to the HW structure
*
* Reads the firmware semaphore register and returns true (>0) if
diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 3031d6d..fc5c63f 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -1006,7 +1006,7 @@ static void e1000_irq_enable(struct e1000_adapter *adapter)
* e1000_get_hw_control - get control of the h/w from f/w
* @adapter: address of board private structure
*
- * e1000_get_hw_control sets {CTRL_EXT|FWSM}:DRV_LOAD bit.
+ * e1000_get_hw_control sets {CTRL_EXT|SWSM}:DRV_LOAD bit.
* For ASF and Pass Through versions of f/w this means that
* the driver is loaded. For AMT version (only with 82573)
* of the f/w this means that the network i/f is open.
@@ -1032,7 +1032,7 @@ static void e1000_get_hw_control(struct e1000_adapter *adapter)
* e1000_release_hw_control - release control of the h/w to f/w
* @adapter: address of board private structure
*
- * e1000_release_hw_control resets {CTRL_EXT|FWSM}:DRV_LOAD bit.
+ * e1000_release_hw_control resets {CTRL_EXT|SWSM}:DRV_LOAD bit.
* For ASF and Pass Through versions of f/w this means that the
* driver is no longer loaded. For AMT version (only with 82573) i
* of the f/w this means that the network i/f is closed.
@@ -1241,6 +1241,11 @@ void e1000e_free_rx_resources(struct e1000_adapter *adapter)
/**
* e1000_update_itr - update the dynamic ITR value based on statistics
+ * @adapter: pointer to adapter
+ * @itr_setting: current adapter->itr
+ * @packets: the number of packets during this measurement interval
+ * @bytes: the number of bytes during this measurement interval
+ *
* Stores a new ITR value based on packets and byte
* counts during the last interrupt. The advantage of per interrupt
* computation is faster updates and more accurate ITR for the current
@@ -1250,10 +1255,6 @@ void e1000e_free_rx_resources(struct e1000_adapter *adapter)
* while increasing bulk throughput.
* this functionality is controlled by the InterruptThrottleRate module
* parameter (see e1000_param.c)
- * @adapter: pointer to adapter
- * @itr_setting: current adapter->itr
- * @packets: the number of packets during this measurement interval
- * @bytes: the number of bytes during this measurement interval
**/
static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
u16 itr_setting, int packets,
@@ -1366,6 +1367,7 @@ set_itr_now:
/**
* e1000_clean - NAPI Rx polling callback
* @adapter: board private structure
+ * @budget: amount of packets driver is allowed to process this poll
**/
static int e1000_clean(struct napi_struct *napi, int budget)
{
@@ -2000,7 +2002,7 @@ static void e1000_power_down_phy(struct e1000_adapter *adapter)
e1000_check_reset_block(hw))
return;
- /* managebility (AMT) is enabled */
+ /* manageability (AMT) is enabled */
if (er32(MANC) & E1000_MANC_SMBUS_EN)
return;
@@ -3488,7 +3490,6 @@ static int e1000_suspend(struct pci_dev *pdev, pm_message_t state)
static void e1000e_disable_l1aspm(struct pci_dev *pdev)
{
int pos;
- u32 cap;
u16 val;
/*
@@ -3503,7 +3504,6 @@ static void e1000e_disable_l1aspm(struct pci_dev *pdev)
* active.
*/
pos = pci_find_capability(pdev, PCI_CAP_ID_EXP);
- pci_read_config_dword(pdev, pos + PCI_EXP_LNKCAP, &cap);
pci_read_config_word(pdev, pos + PCI_EXP_LNKCTL, &val);
if (val & 0x2) {
dev_warn(&pdev->dev, "Disabling L1 ASPM\n");
diff --git a/drivers/net/e1000e/phy.c b/drivers/net/e1000e/phy.c
index fc6fee1..dab3c46 100644
--- a/drivers/net/e1000e/phy.c
+++ b/drivers/net/e1000e/phy.c
@@ -121,7 +121,7 @@ s32 e1000e_phy_reset_dsp(struct e1000_hw *hw)
* @offset: register offset to be read
* @data: pointer to the read data
*
- * Reads the MDI control regsiter in the PHY at offset and stores the
+ * Reads the MDI control register in the PHY at offset and stores the
* information read to data.
**/
static s32 e1000_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
@@ -1172,7 +1172,7 @@ s32 e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active)
}
/**
- * e1000e_check_downshift - Checks whether a downshift in speed occured
+ * e1000e_check_downshift - Checks whether a downshift in speed occurred
* @hw: pointer to the HW structure
*
* Success returns 0, Failure returns 1
@@ -1388,8 +1388,8 @@ s32 e1000e_get_cable_length_m88(struct e1000_hw *hw)
*
* The automatic gain control (agc) normalizes the amplitude of the
* received signal, adjusting for the attenuation produced by the
- * cable. By reading the AGC registers, which reperesent the
- * cobination of course and fine gain value, the value can be put
+ * cable. By reading the AGC registers, which represent the
+ * combination of course and fine gain value, the value can be put
* into a lookup table to obtain the approximate cable length
* for each channel.
**/
@@ -1619,7 +1619,7 @@ s32 e1000e_phy_sw_reset(struct e1000_hw *hw)
* Verify the reset block is not blocking us from resetting. Acquire
* semaphore (if necessary) and read/set/write the device control reset
* bit in the PHY. Wait the appropriate delay time for the device to
- * reset and relase the semaphore (if necessary).
+ * reset and release the semaphore (if necessary).
**/
s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw)
{
diff --git a/drivers/net/ehea/ehea.h b/drivers/net/ehea/ehea.h
index 88fb53e..7c4ead3 100644
--- a/drivers/net/ehea/ehea.h
+++ b/drivers/net/ehea/ehea.h
@@ -40,7 +40,7 @@
#include <asm/io.h>
#define DRV_NAME "ehea"
-#define DRV_VERSION "EHEA_0083"
+#define DRV_VERSION "EHEA_0087"
/* eHEA capability flags */
#define DLPAR_PORT_ADD_REM 1
@@ -386,6 +386,13 @@ struct ehea_port_res {
#define EHEA_MAX_PORTS 16
+
+#define EHEA_NUM_PORTRES_FW_HANDLES 6 /* QP handle, SendCQ handle,
+ RecvCQ handle, EQ handle,
+ SendMR handle, RecvMR handle */
+#define EHEA_NUM_PORT_FW_HANDLES 1 /* EQ handle */
+#define EHEA_NUM_ADAPTER_FW_HANDLES 2 /* MR handle, NEQ handle */
+
struct ehea_adapter {
u64 handle;
struct of_device *ofdev;
@@ -405,6 +412,31 @@ struct ehea_mc_list {
u64 macaddr;
};
+/* kdump support */
+struct ehea_fw_handle_entry {
+ u64 adh; /* Adapter Handle */
+ u64 fwh; /* Firmware Handle */
+};
+
+struct ehea_fw_handle_array {
+ struct ehea_fw_handle_entry *arr;
+ int num_entries;
+ struct semaphore lock;
+};
+
+struct ehea_bcmc_reg_entry {
+ u64 adh; /* Adapter Handle */
+ u32 port_id; /* Logical Port Id */
+ u8 reg_type; /* Registration Type */
+ u64 macaddr;
+};
+
+struct ehea_bcmc_reg_array {
+ struct ehea_bcmc_reg_entry *arr;
+ int num_entries;
+ struct semaphore lock;
+};
+
#define EHEA_PORT_UP 1
#define EHEA_PORT_DOWN 0
#define EHEA_PHY_LINK_UP 1
diff --git a/drivers/net/ehea/ehea_main.c b/drivers/net/ehea/ehea_main.c
index c051c7e..21af674 100644
--- a/drivers/net/ehea/ehea_main.c
+++ b/drivers/net/ehea/ehea_main.c
@@ -35,6 +35,7 @@
#include <linux/if_ether.h>
#include <linux/notifier.h>
#include <linux/reboot.h>
+#include <asm/kexec.h>
#include <net/ip.h>
@@ -98,8 +99,10 @@ static int port_name_cnt;
static LIST_HEAD(adapter_list);
u64 ehea_driver_flags;
struct work_struct ehea_rereg_mr_task;
-
struct semaphore dlpar_mem_lock;
+struct ehea_fw_handle_array ehea_fw_handles;
+struct ehea_bcmc_reg_array ehea_bcmc_regs;
+
static int __devinit ehea_probe_adapter(struct of_device *dev,
const struct of_device_id *id);
@@ -132,6 +135,160 @@ void ehea_dump(void *adr, int len, char *msg)
}
}
+static void ehea_update_firmware_handles(void)
+{
+ struct ehea_fw_handle_entry *arr = NULL;
+ struct ehea_adapter *adapter;
+ int num_adapters = 0;
+ int num_ports = 0;
+ int num_portres = 0;
+ int i = 0;
+ int num_fw_handles, k, l;
+
+ /* Determine number of handles */
+ list_for_each_entry(adapter, &adapter_list, list) {
+ num_adapters++;
+
+ for (k = 0; k < EHEA_MAX_PORTS; k++) {
+ struct ehea_port *port = adapter->port[k];
+
+ if (!port || (port->state != EHEA_PORT_UP))
+ continue;
+
+ num_ports++;
+ num_portres += port->num_def_qps + port->num_add_tx_qps;
+ }
+ }
+
+ num_fw_handles = num_adapters * EHEA_NUM_ADAPTER_FW_HANDLES +
+ num_ports * EHEA_NUM_PORT_FW_HANDLES +
+ num_portres * EHEA_NUM_PORTRES_FW_HANDLES;
+
+ if (num_fw_handles) {
+ arr = kzalloc(num_fw_handles * sizeof(*arr), GFP_KERNEL);
+ if (!arr)
+ return; /* Keep the existing array */
+ } else
+ goto out_update;
+
+ list_for_each_entry(adapter, &adapter_list, list) {
+ for (k = 0; k < EHEA_MAX_PORTS; k++) {
+ struct ehea_port *port = adapter->port[k];
+
+ if (!port || (port->state != EHEA_PORT_UP))
+ continue;
+
+ for (l = 0;
+ l < port->num_def_qps + port->num_add_tx_qps;
+ l++) {
+ struct ehea_port_res *pr = &port->port_res[l];
+
+ arr[i].adh = adapter->handle;
+ arr[i++].fwh = pr->qp->fw_handle;
+ arr[i].adh = adapter->handle;
+ arr[i++].fwh = pr->send_cq->fw_handle;
+ arr[i].adh = adapter->handle;
+ arr[i++].fwh = pr->recv_cq->fw_handle;
+ arr[i].adh = adapter->handle;
+ arr[i++].fwh = pr->eq->fw_handle;
+ arr[i].adh = adapter->handle;
+ arr[i++].fwh = pr->send_mr.handle;
+ arr[i].adh = adapter->handle;
+ arr[i++].fwh = pr->recv_mr.handle;
+ }
+ arr[i].adh = adapter->handle;
+ arr[i++].fwh = port->qp_eq->fw_handle;
+ }
+
+ arr[i].adh = adapter->handle;
+ arr[i++].fwh = adapter->neq->fw_handle;
+
+ if (adapter->mr.handle) {
+ arr[i].adh = adapter->handle;
+ arr[i++].fwh = adapter->mr.handle;
+ }
+ }
+
+out_update:
+ kfree(ehea_fw_handles.arr);
+ ehea_fw_handles.arr = arr;
+ ehea_fw_handles.num_entries = i;
+}
+
+static void ehea_update_bcmc_registrations(void)
+{
+ struct ehea_bcmc_reg_entry *arr = NULL;
+ struct ehea_adapter *adapter;
+ struct ehea_mc_list *mc_entry;
+ int num_registrations = 0;
+ int i = 0;
+ int k;
+
+ /* Determine number of registrations */
+ list_for_each_entry(adapter, &adapter_list, list)
+ for (k = 0; k < EHEA_MAX_PORTS; k++) {
+ struct ehea_port *port = adapter->port[k];
+
+ if (!port || (port->state != EHEA_PORT_UP))
+ continue;
+
+ num_registrations += 2; /* Broadcast registrations */
+
+ list_for_each_entry(mc_entry, &port->mc_list->list,list)
+ num_registrations += 2;
+ }
+
+ if (num_registrations) {
+ arr = kzalloc(num_registrations * sizeof(*arr), GFP_KERNEL);
+ if (!arr)
+ return; /* Keep the existing array */
+ } else
+ goto out_update;
+
+ list_for_each_entry(adapter, &adapter_list, list) {
+ for (k = 0; k < EHEA_MAX_PORTS; k++) {
+ struct ehea_port *port = adapter->port[k];
+
+ if (!port || (port->state != EHEA_PORT_UP))
+ continue;
+
+ arr[i].adh = adapter->handle;
+ arr[i].port_id = port->logical_port_id;
+ arr[i].reg_type = EHEA_BCMC_BROADCAST |
+ EHEA_BCMC_UNTAGGED;
+ arr[i++].macaddr = port->mac_addr;
+
+ arr[i].adh = adapter->handle;
+ arr[i].port_id = port->logical_port_id;
+ arr[i].reg_type = EHEA_BCMC_BROADCAST |
+ EHEA_BCMC_VLANID_ALL;
+ arr[i++].macaddr = port->mac_addr;
+
+ list_for_each_entry(mc_entry,
+ &port->mc_list->list, list) {
+ arr[i].adh = adapter->handle;
+ arr[i].port_id = port->logical_port_id;
+ arr[i].reg_type = EHEA_BCMC_SCOPE_ALL |
+ EHEA_BCMC_MULTICAST |
+ EHEA_BCMC_UNTAGGED;
+ arr[i++].macaddr = mc_entry->macaddr;
+
+ arr[i].adh = adapter->handle;
+ arr[i].port_id = port->logical_port_id;
+ arr[i].reg_type = EHEA_BCMC_SCOPE_ALL |
+ EHEA_BCMC_MULTICAST |
+ EHEA_BCMC_VLANID_ALL;
+ arr[i++].macaddr = mc_entry->macaddr;
+ }
+ }
+ }
+
+out_update:
+ kfree(ehea_bcmc_regs.arr);
+ ehea_bcmc_regs.arr = arr;
+ ehea_bcmc_regs.num_entries = i;
+}
+
static struct net_device_stats *ehea_get_stats(struct net_device *dev)
{
struct ehea_port *port = netdev_priv(dev);
@@ -1601,19 +1758,25 @@ static int ehea_set_mac_addr(struct net_device *dev, void *sa)
memcpy(dev->dev_addr, mac_addr->sa_data, dev->addr_len);
+ down(&ehea_bcmc_regs.lock);
+
/* Deregister old MAC in pHYP */
ret = ehea_broadcast_reg_helper(port, H_DEREG_BCMC);
if (ret)
- goto out_free;
+ goto out_upregs;
port->mac_addr = cb0->port_mac_addr << 16;
/* Register new MAC in pHYP */
ret = ehea_broadcast_reg_helper(port, H_REG_BCMC);
if (ret)
- goto out_free;
+ goto out_upregs;
ret = 0;
+
+out_upregs:
+ ehea_update_bcmc_registrations();
+ up(&ehea_bcmc_regs.lock);
out_free:
kfree(cb0);
out:
@@ -1775,9 +1938,11 @@ static void ehea_set_multicast_list(struct net_device *dev)
}
ehea_promiscuous(dev, 0);
+ down(&ehea_bcmc_regs.lock);
+
if (dev->flags & IFF_ALLMULTI) {
ehea_allmulti(dev, 1);
- return;
+ goto out;
}
ehea_allmulti(dev, 0);
@@ -1803,6 +1968,8 @@ static void ehea_set_multicast_list(struct net_device *dev)
}
out:
+ ehea_update_bcmc_registrations();
+ up(&ehea_bcmc_regs.lock);
return;
}
@@ -2285,6 +2452,8 @@ static int ehea_up(struct net_device *dev)
if (port->state == EHEA_PORT_UP)
return 0;
+ down(&ehea_fw_handles.lock);
+
ret = ehea_port_res_setup(port, port->num_def_qps,
port->num_add_tx_qps);
if (ret) {
@@ -2321,8 +2490,17 @@ static int ehea_up(struct net_device *dev)
}
}
- ret = 0;
+ down(&ehea_bcmc_regs.lock);
+
+ ret = ehea_broadcast_reg_helper(port, H_REG_BCMC);
+ if (ret) {
+ ret = -EIO;
+ goto out_free_irqs;
+ }
+
port->state = EHEA_PORT_UP;
+
+ ret = 0;
goto out;
out_free_irqs:
@@ -2334,6 +2512,12 @@ out:
if (ret)
ehea_info("Failed starting %s. ret=%i", dev->name, ret);
+ ehea_update_bcmc_registrations();
+ up(&ehea_bcmc_regs.lock);
+
+ ehea_update_firmware_handles();
+ up(&ehea_fw_handles.lock);
+
return ret;
}
@@ -2382,16 +2566,27 @@ static int ehea_down(struct net_device *dev)
if (port->state == EHEA_PORT_DOWN)
return 0;
+ down(&ehea_bcmc_regs.lock);
ehea_drop_multicast_list(dev);
+ ehea_broadcast_reg_helper(port, H_DEREG_BCMC);
+
ehea_free_interrupts(dev);
+ down(&ehea_fw_handles.lock);
+
port->state = EHEA_PORT_DOWN;
+ ehea_update_bcmc_registrations();
+ up(&ehea_bcmc_regs.lock);
+
ret = ehea_clean_all_portres(port);
if (ret)
ehea_info("Failed freeing resources for %s. ret=%i",
dev->name, ret);
+ ehea_update_firmware_handles();
+ up(&ehea_fw_handles.lock);
+
return ret;
}
@@ -2920,19 +3115,12 @@ struct ehea_port *ehea_setup_single_port(struct ehea_adapter *adapter,
dev->watchdog_timeo = EHEA_WATCH_DOG_TIMEOUT;
INIT_WORK(&port->reset_task, ehea_reset_port);
-
- ret = ehea_broadcast_reg_helper(port, H_REG_BCMC);
- if (ret) {
- ret = -EIO;
- goto out_unreg_port;
- }
-
ehea_set_ethtool_ops(dev);
ret = register_netdev(dev);
if (ret) {
ehea_error("register_netdev failed. ret=%d", ret);
- goto out_dereg_bc;
+ goto out_unreg_port;
}
port->lro_max_aggr = lro_max_aggr;
@@ -2949,9 +3137,6 @@ struct ehea_port *ehea_setup_single_port(struct ehea_adapter *adapter,
return port;
-out_dereg_bc:
- ehea_broadcast_reg_helper(port, H_DEREG_BCMC);
-
out_unreg_port:
ehea_unregister_port(port);
@@ -2971,7 +3156,6 @@ static void ehea_shutdown_single_port(struct ehea_port *port)
{
unregister_netdev(port->netdev);
ehea_unregister_port(port);
- ehea_broadcast_reg_helper(port, H_DEREG_BCMC);
kfree(port->mc_list);
free_netdev(port->netdev);
port->adapter->active_ports--;
@@ -3014,7 +3198,6 @@ static int ehea_setup_ports(struct ehea_adapter *adapter)
i++;
};
-
return 0;
}
@@ -3159,6 +3342,7 @@ static int __devinit ehea_probe_adapter(struct of_device *dev,
ehea_error("Invalid ibmebus device probed");
return -EINVAL;
}
+ down(&ehea_fw_handles.lock);
adapter = kzalloc(sizeof(*adapter), GFP_KERNEL);
if (!adapter) {
@@ -3239,7 +3423,10 @@ out_kill_eq:
out_free_ad:
kfree(adapter);
+
out:
+ ehea_update_firmware_handles();
+ up(&ehea_fw_handles.lock);
return ret;
}
@@ -3258,18 +3445,41 @@ static int __devexit ehea_remove(struct of_device *dev)
flush_scheduled_work();
+ down(&ehea_fw_handles.lock);
+
ibmebus_free_irq(adapter->neq->attr.ist1, adapter);
tasklet_kill(&adapter->neq_tasklet);
ehea_destroy_eq(adapter->neq);
ehea_remove_adapter_mr(adapter);
list_del(&adapter->list);
-
kfree(adapter);
+ ehea_update_firmware_handles();
+ up(&ehea_fw_handles.lock);
+
return 0;
}
+void ehea_crash_handler(void)
+{
+ int i;
+
+ if (ehea_fw_handles.arr)
+ for (i = 0; i < ehea_fw_handles.num_entries; i++)
+ ehea_h_free_resource(ehea_fw_handles.arr[i].adh,
+ ehea_fw_handles.arr[i].fwh,
+ FORCE_FREE);
+
+ if (ehea_bcmc_regs.arr)
+ for (i = 0; i < ehea_bcmc_regs.num_entries; i++)
+ ehea_h_reg_dereg_bcmc(ehea_bcmc_regs.arr[i].adh,
+ ehea_bcmc_regs.arr[i].port_id,
+ ehea_bcmc_regs.arr[i].reg_type,
+ ehea_bcmc_regs.arr[i].macaddr,
+ 0, H_DEREG_BCMC);
+}
+
static int ehea_reboot_notifier(struct notifier_block *nb,
unsigned long action, void *unused)
{
@@ -3330,7 +3540,12 @@ int __init ehea_module_init(void)
INIT_WORK(&ehea_rereg_mr_task, ehea_rereg_mrs);
+ memset(&ehea_fw_handles, 0, sizeof(ehea_fw_handles));
+ memset(&ehea_bcmc_regs, 0, sizeof(ehea_bcmc_regs));
+
sema_init(&dlpar_mem_lock, 1);
+ sema_init(&ehea_fw_handles.lock, 1);
+ sema_init(&ehea_bcmc_regs.lock, 1);
ret = check_module_parm();
if (ret)
@@ -3340,12 +3555,18 @@ int __init ehea_module_init(void)
if (ret)
goto out;
- register_reboot_notifier(&ehea_reboot_nb);
+ ret = register_reboot_notifier(&ehea_reboot_nb);
+ if (ret)
+ ehea_info("failed registering reboot notifier");
+
+ ret = crash_shutdown_register(&ehea_crash_handler);
+ if (ret)
+ ehea_info("failed registering crash handler");
ret = ibmebus_register_driver(&ehea_driver);
if (ret) {
ehea_error("failed registering eHEA device driver on ebus");
- goto out;
+ goto out2;
}
ret = driver_create_file(&ehea_driver.driver,
@@ -3353,21 +3574,33 @@ int __init ehea_module_init(void)
if (ret) {
ehea_error("failed to register capabilities attribute, ret=%d",
ret);
- unregister_reboot_notifier(&ehea_reboot_nb);
- ibmebus_unregister_driver(&ehea_driver);
- goto out;
+ goto out3;
}
+ return ret;
+
+out3:
+ ibmebus_unregister_driver(&ehea_driver);
+out2:
+ unregister_reboot_notifier(&ehea_reboot_nb);
+ crash_shutdown_unregister(&ehea_crash_handler);
out:
return ret;
}
static void __exit ehea_module_exit(void)
{
+ int ret;
+
flush_scheduled_work();
driver_remove_file(&ehea_driver.driver, &driver_attr_capabilities);
ibmebus_unregister_driver(&ehea_driver);
unregister_reboot_notifier(&ehea_reboot_nb);
+ ret = crash_shutdown_unregister(&ehea_crash_handler);
+ if (ret)
+ ehea_info("failed unregistering crash handler");
+ kfree(ehea_fw_handles.arr);
+ kfree(ehea_bcmc_regs.arr);
ehea_destroy_busmap();
}
diff --git a/drivers/net/fs_enet/fs_enet-main.c b/drivers/net/fs_enet/fs_enet-main.c
index 42d94ed..af869cf 100644
--- a/drivers/net/fs_enet/fs_enet-main.c
+++ b/drivers/net/fs_enet/fs_enet-main.c
@@ -946,16 +946,11 @@ static int fs_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
{
struct fs_enet_private *fep = netdev_priv(dev);
struct mii_ioctl_data *mii = (struct mii_ioctl_data *)&rq->ifr_data;
- unsigned long flags;
- int rc;
if (!netif_running(dev))
return -EINVAL;
- spin_lock_irqsave(&fep->lock, flags);
- rc = phy_mii_ioctl(fep->phydev, mii, cmd);
- spin_unlock_irqrestore(&fep->lock, flags);
- return rc;
+ return phy_mii_ioctl(fep->phydev, mii, cmd);
}
extern int fs_mii_connect(struct net_device *dev);
diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c
index 4244fc2..718cf77 100644
--- a/drivers/net/gianfar.c
+++ b/drivers/net/gianfar.c
@@ -605,7 +605,7 @@ void stop_gfar(struct net_device *dev)
free_skb_resources(priv);
- dma_free_coherent(NULL,
+ dma_free_coherent(&dev->dev,
sizeof(struct txbd8)*priv->tx_ring_size
+ sizeof(struct rxbd8)*priv->rx_ring_size,
priv->tx_bd_base,
@@ -626,7 +626,7 @@ static void free_skb_resources(struct gfar_private *priv)
for (i = 0; i < priv->tx_ring_size; i++) {
if (priv->tx_skbuff[i]) {
- dma_unmap_single(NULL, txbdp->bufPtr,
+ dma_unmap_single(&priv->dev->dev, txbdp->bufPtr,
txbdp->length,
DMA_TO_DEVICE);
dev_kfree_skb_any(priv->tx_skbuff[i]);
@@ -643,7 +643,7 @@ static void free_skb_resources(struct gfar_private *priv)
if(priv->rx_skbuff != NULL) {
for (i = 0; i < priv->rx_ring_size; i++) {
if (priv->rx_skbuff[i]) {
- dma_unmap_single(NULL, rxbdp->bufPtr,
+ dma_unmap_single(&priv->dev->dev, rxbdp->bufPtr,
priv->rx_buffer_size,
DMA_FROM_DEVICE);
@@ -708,7 +708,7 @@ int startup_gfar(struct net_device *dev)
gfar_write(®s->imask, IMASK_INIT_CLEAR);
/* Allocate memory for the buffer descriptors */
- vaddr = (unsigned long) dma_alloc_coherent(NULL,
+ vaddr = (unsigned long) dma_alloc_coherent(&dev->dev,
sizeof (struct txbd8) * priv->tx_ring_size +
sizeof (struct rxbd8) * priv->rx_ring_size,
&addr, GFP_KERNEL);
@@ -919,7 +919,7 @@ err_irq_fail:
rx_skb_fail:
free_skb_resources(priv);
tx_skb_fail:
- dma_free_coherent(NULL,
+ dma_free_coherent(&dev->dev,
sizeof(struct txbd8)*priv->tx_ring_size
+ sizeof(struct rxbd8)*priv->rx_ring_size,
priv->tx_bd_base,
@@ -1053,7 +1053,7 @@ static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev)
/* Set buffer length and pointer */
txbdp->length = skb->len;
- txbdp->bufPtr = dma_map_single(NULL, skb->data,
+ txbdp->bufPtr = dma_map_single(&dev->dev, skb->data,
skb->len, DMA_TO_DEVICE);
/* Save the skb pointer so we can free it later */
@@ -1332,7 +1332,7 @@ struct sk_buff * gfar_new_skb(struct net_device *dev, struct rxbd8 *bdp)
*/
skb_reserve(skb, alignamount);
- bdp->bufPtr = dma_map_single(NULL, skb->data,
+ bdp->bufPtr = dma_map_single(&dev->dev, skb->data,
priv->rx_buffer_size, DMA_FROM_DEVICE);
bdp->length = 0;
diff --git a/drivers/net/igb/igb_main.c b/drivers/net/igb/igb_main.c
index bff280e..6a1f230 100644
--- a/drivers/net/igb/igb_main.c
+++ b/drivers/net/igb/igb_main.c
@@ -439,7 +439,7 @@ static int igb_request_irq(struct igb_adapter *adapter)
err = igb_request_msix(adapter);
if (!err) {
/* enable IAM, auto-mask,
- * DO NOT USE EIAME or IAME in legacy mode */
+ * DO NOT USE EIAM or IAM in legacy mode */
wr32(E1000_IAM, IMS_ENABLE_MASK);
goto request_done;
}
@@ -465,14 +465,9 @@ static int igb_request_irq(struct igb_adapter *adapter)
err = request_irq(adapter->pdev->irq, &igb_intr, IRQF_SHARED,
netdev->name, netdev);
- if (err) {
+ if (err)
dev_err(&adapter->pdev->dev, "Error %d getting interrupt\n",
err);
- goto request_done;
- }
-
- /* enable IAM, auto-mask */
- wr32(E1000_IAM, IMS_ENABLE_MASK);
request_done:
return err;
@@ -821,7 +816,8 @@ void igb_reset(struct igb_adapter *adapter)
wr32(E1000_VET, ETHERNET_IEEE_VLAN_TYPE);
igb_reset_adaptive(&adapter->hw);
- adapter->hw.phy.ops.get_phy_info(&adapter->hw);
+ if (adapter->hw.phy.ops.get_phy_info)
+ adapter->hw.phy.ops.get_phy_info(&adapter->hw);
}
/**
@@ -2057,7 +2053,8 @@ static void igb_set_multi(struct net_device *netdev)
static void igb_update_phy_info(unsigned long data)
{
struct igb_adapter *adapter = (struct igb_adapter *) data;
- adapter->hw.phy.ops.get_phy_info(&adapter->hw);
+ if (adapter->hw.phy.ops.get_phy_info)
+ adapter->hw.phy.ops.get_phy_info(&adapter->hw);
}
/**
diff --git a/drivers/net/ixgb/ixgb_ethtool.c b/drivers/net/ixgb/ixgb_ethtool.c
index 53a9fd0..75f3a68 100644
--- a/drivers/net/ixgb/ixgb_ethtool.c
+++ b/drivers/net/ixgb/ixgb_ethtool.c
@@ -67,6 +67,7 @@ static struct ixgb_stats ixgb_gstrings_stats[] = {
{"rx_over_errors", IXGB_STAT(net_stats.rx_over_errors)},
{"rx_crc_errors", IXGB_STAT(net_stats.rx_crc_errors)},
{"rx_frame_errors", IXGB_STAT(net_stats.rx_frame_errors)},
+ {"rx_no_buffer_count", IXGB_STAT(stats.rnbc)},
{"rx_fifo_errors", IXGB_STAT(net_stats.rx_fifo_errors)},
{"rx_missed_errors", IXGB_STAT(net_stats.rx_missed_errors)},
{"tx_aborted_errors", IXGB_STAT(net_stats.tx_aborted_errors)},
diff --git a/drivers/net/macb.c b/drivers/net/macb.c
index 81bf005..1d210ed 100644
--- a/drivers/net/macb.c
+++ b/drivers/net/macb.c
@@ -148,7 +148,7 @@ static void macb_handle_link_change(struct net_device *dev)
if (phydev->duplex)
reg |= MACB_BIT(FD);
- if (phydev->speed)
+ if (phydev->speed == SPEED_100)
reg |= MACB_BIT(SPD);
macb_writel(bp, NCFGR, reg);
diff --git a/drivers/net/pcmcia/pcnet_cs.c b/drivers/net/pcmcia/pcnet_cs.c
index 6323988..fd8158a 100644
--- a/drivers/net/pcmcia/pcnet_cs.c
+++ b/drivers/net/pcmcia/pcnet_cs.c
@@ -590,6 +590,13 @@ static int pcnet_config(struct pcmcia_device *link)
dev->if_port = 0;
}
+ if ((link->conf.ConfigBase == 0x03c0)
+ && (link->manf_id == 0x149) && (link->card_id = 0xc1ab)) {
+ printk(KERN_INFO "pcnet_cs: this is an AX88190 card!\n");
+ printk(KERN_INFO "pcnet_cs: use axnet_cs instead.\n");
+ goto failed;
+ }
+
local_hw_info = get_hwinfo(link);
if (local_hw_info == NULL)
local_hw_info = get_prom(link);
@@ -1567,12 +1574,11 @@ static struct pcmcia_device_id pcnet_ids[] = {
PCMCIA_DEVICE_MANF_CARD(0x0104, 0x0145),
PCMCIA_DEVICE_MANF_CARD(0x0149, 0x0230),
PCMCIA_DEVICE_MANF_CARD(0x0149, 0x4530),
-/* PCMCIA_DEVICE_MANF_CARD(0x0149, 0xc1ab), conflict with axnet_cs */
+ PCMCIA_DEVICE_MANF_CARD(0x0149, 0xc1ab),
PCMCIA_DEVICE_MANF_CARD(0x0186, 0x0110),
PCMCIA_DEVICE_MANF_CARD(0x01bf, 0x2328),
PCMCIA_DEVICE_MANF_CARD(0x01bf, 0x8041),
PCMCIA_DEVICE_MANF_CARD(0x0213, 0x2452),
-/* PCMCIA_DEVICE_MANF_CARD(0x021b, 0x0202), conflict with axnet_cs */
PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0300),
PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0307),
PCMCIA_DEVICE_MANF_CARD(0x026f, 0x030a),
diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c
index 6e9f619..963630c 100644
--- a/drivers/net/phy/mdio_bus.c
+++ b/drivers/net/phy/mdio_bus.c
@@ -49,13 +49,13 @@ int mdiobus_register(struct mii_bus *bus)
int i;
int err = 0;
- mutex_init(&bus->mdio_lock);
-
if (NULL == bus || NULL == bus->name ||
NULL == bus->read ||
NULL == bus->write)
return -EINVAL;
+ mutex_init(&bus->mdio_lock);
+
if (bus->reset)
bus->reset(bus);
diff --git a/drivers/net/sis190.c b/drivers/net/sis190.c
index 202fdf3..20745fd 100644
--- a/drivers/net/sis190.c
+++ b/drivers/net/sis190.c
@@ -1633,13 +1633,18 @@ static inline void sis190_init_rxfilter(struct net_device *dev)
static int __devinit sis190_get_mac_addr(struct pci_dev *pdev,
struct net_device *dev)
{
- u8 from;
+ int rc;
+
+ rc = sis190_get_mac_addr_from_eeprom(pdev, dev);
+ if (rc < 0) {
+ u8 reg;
- pci_read_config_byte(pdev, 0x73, &from);
+ pci_read_config_byte(pdev, 0x73, ®);
- return (from & 0x00000001) ?
- sis190_get_mac_addr_from_apc(pdev, dev) :
- sis190_get_mac_addr_from_eeprom(pdev, dev);
+ if (reg & 0x00000001)
+ rc = sis190_get_mac_addr_from_apc(pdev, dev);
+ }
+ return rc;
}
static void sis190_set_speed_auto(struct net_device *dev)
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index 9a62959..54c6626 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -572,8 +572,9 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
default:
/* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */
ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) | PHY_M_LEDC_TX_CTRL;
+
/* turn off the Rx LED (LED_RX) */
- ledover &= ~PHY_M_LED_MO_RX;
+ ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
}
if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
@@ -602,7 +603,7 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
/* turn on 100 Mbps LED (LED_LINK100) */
- ledover |= PHY_M_LED_MO_100;
+ ledover |= PHY_M_LED_MO_100(MO_LED_ON);
}
if (ledover)
@@ -3322,82 +3323,80 @@ static void sky2_set_multicast(struct net_device *dev)
/* Can have one global because blinking is controlled by
* ethtool and that is always under RTNL mutex
*/
-static void sky2_led(struct sky2_hw *hw, unsigned port, int on)
+static void sky2_led(struct sky2_port *sky2, enum led_mode mode)
{
- u16 pg;
+ struct sky2_hw *hw = sky2->hw;
+ unsigned port = sky2->port;
- switch (hw->chip_id) {
- case CHIP_ID_YUKON_XL:
+ spin_lock_bh(&sky2->phy_lock);
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U ||
+ hw->chip_id == CHIP_ID_YUKON_EX ||
+ hw->chip_id == CHIP_ID_YUKON_SUPR) {
+ u16 pg;
pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
- gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
- on ? (PHY_M_LEDC_LOS_CTRL(1) |
- PHY_M_LEDC_INIT_CTRL(7) |
- PHY_M_LEDC_STA1_CTRL(7) |
- PHY_M_LEDC_STA0_CTRL(7))
- : 0);
- gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
- break;
+ switch (mode) {
+ case MO_LED_OFF:
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
+ PHY_M_LEDC_LOS_CTRL(8) |
+ PHY_M_LEDC_INIT_CTRL(8) |
+ PHY_M_LEDC_STA1_CTRL(8) |
+ PHY_M_LEDC_STA0_CTRL(8));
+ break;
+ case MO_LED_ON:
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
+ PHY_M_LEDC_LOS_CTRL(9) |
+ PHY_M_LEDC_INIT_CTRL(9) |
+ PHY_M_LEDC_STA1_CTRL(9) |
+ PHY_M_LEDC_STA0_CTRL(9));
+ break;
+ case MO_LED_BLINK:
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
+ PHY_M_LEDC_LOS_CTRL(0xa) |
+ PHY_M_LEDC_INIT_CTRL(0xa) |
+ PHY_M_LEDC_STA1_CTRL(0xa) |
+ PHY_M_LEDC_STA0_CTRL(0xa));
+ break;
+ case MO_LED_NORM:
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
+ PHY_M_LEDC_LOS_CTRL(1) |
+ PHY_M_LEDC_INIT_CTRL(8) |
+ PHY_M_LEDC_STA1_CTRL(7) |
+ PHY_M_LEDC_STA0_CTRL(7));
+ }
- default:
- gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
+ } else
gm_phy_write(hw, port, PHY_MARV_LED_OVER,
- on ? PHY_M_LED_ALL : 0);
- }
+ PHY_M_LED_MO_DUP(mode) |
+ PHY_M_LED_MO_10(mode) |
+ PHY_M_LED_MO_100(mode) |
+ PHY_M_LED_MO_1000(mode) |
+ PHY_M_LED_MO_RX(mode) |
+ PHY_M_LED_MO_TX(mode));
+
+ spin_unlock_bh(&sky2->phy_lock);
}
/* blink LED's for finding board */
static int sky2_phys_id(struct net_device *dev, u32 data)
{
struct sky2_port *sky2 = netdev_priv(dev);
- struct sky2_hw *hw = sky2->hw;
- unsigned port = sky2->port;
- u16 ledctrl, ledover = 0;
- long ms;
- int interrupted;
- int onoff = 1;
+ unsigned int i;
- if (!data || data > (u32) (MAX_SCHEDULE_TIMEOUT / HZ))
- ms = jiffies_to_msecs(MAX_SCHEDULE_TIMEOUT);
- else
- ms = data * 1000;
-
- /* save initial values */
- spin_lock_bh(&sky2->phy_lock);
- if (hw->chip_id == CHIP_ID_YUKON_XL) {
- u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
- gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
- ledctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
- gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
- } else {
- ledctrl = gm_phy_read(hw, port, PHY_MARV_LED_CTRL);
- ledover = gm_phy_read(hw, port, PHY_MARV_LED_OVER);
- }
-
- interrupted = 0;
- while (!interrupted && ms > 0) {
- sky2_led(hw, port, onoff);
- onoff = !onoff;
-
- spin_unlock_bh(&sky2->phy_lock);
- interrupted = msleep_interruptible(250);
- spin_lock_bh(&sky2->phy_lock);
-
- ms -= 250;
- }
+ if (data == 0)
+ data = UINT_MAX;
- /* resume regularly scheduled programming */
- if (hw->chip_id == CHIP_ID_YUKON_XL) {
- u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
- gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
- gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ledctrl);
- gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
- } else {
- gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
- gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
+ for (i = 0; i < data; i++) {
+ sky2_led(sky2, MO_LED_ON);
+ if (msleep_interruptible(500))
+ break;
+ sky2_led(sky2, MO_LED_OFF);
+ if (msleep_interruptible(500))
+ break;
}
- spin_unlock_bh(&sky2->phy_lock);
+ sky2_led(sky2, MO_LED_NORM);
return 0;
}
diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
index 5ab5c1c..7bb3ba9 100644
--- a/drivers/net/sky2.h
+++ b/drivers/net/sky2.h
@@ -1318,18 +1318,21 @@ enum {
BLINK_670MS = 4,/* 670 ms */
};
-/**** PHY_MARV_LED_OVER 16 bit r/w LED control */
-enum {
- PHY_M_LED_MO_DUP = 3<<10,/* Bit 11..10: Duplex */
- PHY_M_LED_MO_10 = 3<<8, /* Bit 9.. 8: Link 10 */
- PHY_M_LED_MO_100 = 3<<6, /* Bit 7.. 6: Link 100 */
- PHY_M_LED_MO_1000 = 3<<4, /* Bit 5.. 4: Link 1000 */
- PHY_M_LED_MO_RX = 3<<2, /* Bit 3.. 2: Rx */
- PHY_M_LED_MO_TX = 3<<0, /* Bit 1.. 0: Tx */
-
- PHY_M_LED_ALL = PHY_M_LED_MO_DUP | PHY_M_LED_MO_10
- | PHY_M_LED_MO_100 | PHY_M_LED_MO_1000
- | PHY_M_LED_MO_RX,
+/***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/
+#define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */
+
+#define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */
+#define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */
+#define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */
+#define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */
+#define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */
+#define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */
+
+enum led_mode {
+ MO_LED_NORM = 0,
+ MO_LED_BLINK = 1,
+ MO_LED_OFF = 2,
+ MO_LED_ON = 3,
};
/***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/
diff --git a/drivers/net/tlan.c b/drivers/net/tlan.c
index 3af5b92..0166407 100644
--- a/drivers/net/tlan.c
+++ b/drivers/net/tlan.c
@@ -1400,7 +1400,7 @@ static void TLan_SetMulticastList( struct net_device *dev )
*
**************************************************************/
-u32 TLan_HandleInvalid( struct net_device *dev, u16 host_int )
+static u32 TLan_HandleInvalid( struct net_device *dev, u16 host_int )
{
/* printk( "TLAN: Invalid interrupt on %s.\n", dev->name ); */
return 0;
@@ -1432,7 +1432,7 @@ u32 TLan_HandleInvalid( struct net_device *dev, u16 host_int )
*
**************************************************************/
-u32 TLan_HandleTxEOF( struct net_device *dev, u16 host_int )
+static u32 TLan_HandleTxEOF( struct net_device *dev, u16 host_int )
{
TLanPrivateInfo *priv = netdev_priv(dev);
int eoc = 0;
@@ -1518,7 +1518,7 @@ u32 TLan_HandleTxEOF( struct net_device *dev, u16 host_int )
*
**************************************************************/
-u32 TLan_HandleStatOverflow( struct net_device *dev, u16 host_int )
+static u32 TLan_HandleStatOverflow( struct net_device *dev, u16 host_int )
{
TLan_ReadAndClearStats( dev, TLAN_RECORD );
@@ -1554,7 +1554,7 @@ u32 TLan_HandleStatOverflow( struct net_device *dev, u16 host_int )
*
**************************************************************/
-u32 TLan_HandleRxEOF( struct net_device *dev, u16 host_int )
+static u32 TLan_HandleRxEOF( struct net_device *dev, u16 host_int )
{
TLanPrivateInfo *priv = netdev_priv(dev);
u32 ack = 0;
@@ -1689,7 +1689,7 @@ u32 TLan_HandleRxEOF( struct net_device *dev, u16 host_int )
*
**************************************************************/
-u32 TLan_HandleDummy( struct net_device *dev, u16 host_int )
+static u32 TLan_HandleDummy( struct net_device *dev, u16 host_int )
{
printk( "TLAN: Test interrupt on %s.\n", dev->name );
return 1;
@@ -1719,7 +1719,7 @@ u32 TLan_HandleDummy( struct net_device *dev, u16 host_int )
*
**************************************************************/
-u32 TLan_HandleTxEOC( struct net_device *dev, u16 host_int )
+static u32 TLan_HandleTxEOC( struct net_device *dev, u16 host_int )
{
TLanPrivateInfo *priv = netdev_priv(dev);
TLanList *head_list;
@@ -1767,7 +1767,7 @@ u32 TLan_HandleTxEOC( struct net_device *dev, u16 host_int )
*
**************************************************************/
-u32 TLan_HandleStatusCheck( struct net_device *dev, u16 host_int )
+static u32 TLan_HandleStatusCheck( struct net_device *dev, u16 host_int )
{
TLanPrivateInfo *priv = netdev_priv(dev);
u32 ack;
@@ -1842,7 +1842,7 @@ u32 TLan_HandleStatusCheck( struct net_device *dev, u16 host_int )
*
**************************************************************/
-u32 TLan_HandleRxEOC( struct net_device *dev, u16 host_int )
+static u32 TLan_HandleRxEOC( struct net_device *dev, u16 host_int )
{
TLanPrivateInfo *priv = netdev_priv(dev);
dma_addr_t head_list_phys;
@@ -1902,7 +1902,7 @@ u32 TLan_HandleRxEOC( struct net_device *dev, u16 host_int )
*
**************************************************************/
-void TLan_Timer( unsigned long data )
+static void TLan_Timer( unsigned long data )
{
struct net_device *dev = (struct net_device *) data;
TLanPrivateInfo *priv = netdev_priv(dev);
@@ -1983,7 +1983,7 @@ void TLan_Timer( unsigned long data )
*
**************************************************************/
-void TLan_ResetLists( struct net_device *dev )
+static void TLan_ResetLists( struct net_device *dev )
{
TLanPrivateInfo *priv = netdev_priv(dev);
int i;
@@ -2043,7 +2043,7 @@ void TLan_ResetLists( struct net_device *dev )
} /* TLan_ResetLists */
-void TLan_FreeLists( struct net_device *dev )
+static void TLan_FreeLists( struct net_device *dev )
{
TLanPrivateInfo *priv = netdev_priv(dev);
int i;
@@ -2092,7 +2092,7 @@ void TLan_FreeLists( struct net_device *dev )
*
**************************************************************/
-void TLan_PrintDio( u16 io_base )
+static void TLan_PrintDio( u16 io_base )
{
u32 data0, data1;
int i;
@@ -2127,7 +2127,7 @@ void TLan_PrintDio( u16 io_base )
*
**************************************************************/
-void TLan_PrintList( TLanList *list, char *type, int num)
+static void TLan_PrintList( TLanList *list, char *type, int num)
{
int i;
@@ -2163,7 +2163,7 @@ void TLan_PrintList( TLanList *list, char *type, int num)
*
**************************************************************/
-void TLan_ReadAndClearStats( struct net_device *dev, int record )
+static void TLan_ReadAndClearStats( struct net_device *dev, int record )
{
TLanPrivateInfo *priv = netdev_priv(dev);
u32 tx_good, tx_under;
@@ -2238,7 +2238,7 @@ void TLan_ReadAndClearStats( struct net_device *dev, int record )
*
**************************************************************/
-void
+static void
TLan_ResetAdapter( struct net_device *dev )
{
TLanPrivateInfo *priv = netdev_priv(dev);
@@ -2324,7 +2324,7 @@ TLan_ResetAdapter( struct net_device *dev )
-void
+static void
TLan_FinishReset( struct net_device *dev )
{
TLanPrivateInfo *priv = netdev_priv(dev);
@@ -2448,7 +2448,7 @@ TLan_FinishReset( struct net_device *dev )
*
**************************************************************/
-void TLan_SetMac( struct net_device *dev, int areg, char *mac )
+static void TLan_SetMac( struct net_device *dev, int areg, char *mac )
{
int i;
@@ -2490,7 +2490,7 @@ void TLan_SetMac( struct net_device *dev, int areg, char *mac )
*
********************************************************************/
-void TLan_PhyPrint( struct net_device *dev )
+static void TLan_PhyPrint( struct net_device *dev )
{
TLanPrivateInfo *priv = netdev_priv(dev);
u16 i, data0, data1, data2, data3, phy;
@@ -2539,7 +2539,7 @@ void TLan_PhyPrint( struct net_device *dev )
*
********************************************************************/
-void TLan_PhyDetect( struct net_device *dev )
+static void TLan_PhyDetect( struct net_device *dev )
{
TLanPrivateInfo *priv = netdev_priv(dev);
u16 control;
@@ -2586,7 +2586,7 @@ void TLan_PhyDetect( struct net_device *dev )
-void TLan_PhyPowerDown( struct net_device *dev )
+static void TLan_PhyPowerDown( struct net_device *dev )
{
TLanPrivateInfo *priv = netdev_priv(dev);
u16 value;
@@ -2611,7 +2611,7 @@ void TLan_PhyPowerDown( struct net_device *dev )
-void TLan_PhyPowerUp( struct net_device *dev )
+static void TLan_PhyPowerUp( struct net_device *dev )
{
TLanPrivateInfo *priv = netdev_priv(dev);
u16 value;
@@ -2632,7 +2632,7 @@ void TLan_PhyPowerUp( struct net_device *dev )
-void TLan_PhyReset( struct net_device *dev )
+static void TLan_PhyReset( struct net_device *dev )
{
TLanPrivateInfo *priv = netdev_priv(dev);
u16 phy;
@@ -2660,7 +2660,7 @@ void TLan_PhyReset( struct net_device *dev )
-void TLan_PhyStartLink( struct net_device *dev )
+static void TLan_PhyStartLink( struct net_device *dev )
{
TLanPrivateInfo *priv = netdev_priv(dev);
u16 ability;
@@ -2747,7 +2747,7 @@ void TLan_PhyStartLink( struct net_device *dev )
-void TLan_PhyFinishAutoNeg( struct net_device *dev )
+static void TLan_PhyFinishAutoNeg( struct net_device *dev )
{
TLanPrivateInfo *priv = netdev_priv(dev);
u16 an_adv;
@@ -2903,7 +2903,7 @@ void TLan_PhyMonitor( struct net_device *dev )
*
**************************************************************/
-int TLan_MiiReadReg( struct net_device *dev, u16 phy, u16 reg, u16 *val )
+static int TLan_MiiReadReg( struct net_device *dev, u16 phy, u16 reg, u16 *val )
{
u8 nack;
u16 sio, tmp;
@@ -2993,7 +2993,7 @@ int TLan_MiiReadReg( struct net_device *dev, u16 phy, u16 reg, u16 *val )
*
**************************************************************/
-void TLan_MiiSendData( u16 base_port, u32 data, unsigned num_bits )
+static void TLan_MiiSendData( u16 base_port, u32 data, unsigned num_bits )
{
u16 sio;
u32 i;
@@ -3035,7 +3035,7 @@ void TLan_MiiSendData( u16 base_port, u32 data, unsigned num_bits )
*
**************************************************************/
-void TLan_MiiSync( u16 base_port )
+static void TLan_MiiSync( u16 base_port )
{
int i;
u16 sio;
@@ -3074,7 +3074,7 @@ void TLan_MiiSync( u16 base_port )
*
**************************************************************/
-void TLan_MiiWriteReg( struct net_device *dev, u16 phy, u16 reg, u16 val )
+static void TLan_MiiWriteReg( struct net_device *dev, u16 phy, u16 reg, u16 val )
{
u16 sio;
int minten;
@@ -3144,7 +3144,7 @@ void TLan_MiiWriteReg( struct net_device *dev, u16 phy, u16 reg, u16 val )
*
**************************************************************/
-void TLan_EeSendStart( u16 io_base )
+static void TLan_EeSendStart( u16 io_base )
{
u16 sio;
@@ -3184,7 +3184,7 @@ void TLan_EeSendStart( u16 io_base )
*
**************************************************************/
-int TLan_EeSendByte( u16 io_base, u8 data, int stop )
+static int TLan_EeSendByte( u16 io_base, u8 data, int stop )
{
int err;
u8 place;
@@ -3245,7 +3245,7 @@ int TLan_EeSendByte( u16 io_base, u8 data, int stop )
*
**************************************************************/
-void TLan_EeReceiveByte( u16 io_base, u8 *data, int stop )
+static void TLan_EeReceiveByte( u16 io_base, u8 *data, int stop )
{
u8 place;
u16 sio;
@@ -3303,7 +3303,7 @@ void TLan_EeReceiveByte( u16 io_base, u8 *data, int stop )
*
**************************************************************/
-int TLan_EeReadByte( struct net_device *dev, u8 ee_addr, u8 *data )
+static int TLan_EeReadByte( struct net_device *dev, u8 ee_addr, u8 *data )
{
int err;
TLanPrivateInfo *priv = netdev_priv(dev);
diff --git a/drivers/net/tulip/uli526x.c b/drivers/net/tulip/uli526x.c
index a7afeea..a59c1f2 100644
--- a/drivers/net/tulip/uli526x.c
+++ b/drivers/net/tulip/uli526x.c
@@ -482,9 +482,11 @@ static void uli526x_init(struct net_device *dev)
struct uli526x_board_info *db = netdev_priv(dev);
unsigned long ioaddr = db->ioaddr;
u8 phy_tmp;
+ u8 timeout;
u16 phy_value;
u16 phy_reg_reset;
+
ULI526X_DBUG(0, "uli526x_init()", 0);
/* Reset M526x MAC controller */
@@ -509,11 +511,19 @@ static void uli526x_init(struct net_device *dev)
/* Parser SROM and media mode */
db->media_mode = uli526x_media_mode;
- /* Phyxcer capability setting */
+ /* phyxcer capability setting */
phy_reg_reset = phy_read(db->ioaddr, db->phy_addr, 0, db->chip_id);
phy_reg_reset = (phy_reg_reset | 0x8000);
phy_write(db->ioaddr, db->phy_addr, 0, phy_reg_reset, db->chip_id);
+
+ /* See IEEE 802.3-2002.pdf (Section 2, Chapter "22.2.4 Management
+ * functions") or phy data sheet for details on phy reset
+ */
udelay(500);
+ timeout = 10;
+ while (timeout-- &&
+ phy_read(db->ioaddr, db->phy_addr, 0, db->chip_id) & 0x8000)
+ udelay(100);
/* Process Phyxcer Media Mode */
uli526x_set_phyxcer(db);
diff --git a/drivers/net/via-rhine.c b/drivers/net/via-rhine.c
index 7c851b1..8c9d6ae 100644
--- a/drivers/net/via-rhine.c
+++ b/drivers/net/via-rhine.c
@@ -1893,7 +1893,7 @@ static void rhine_shutdown (struct pci_dev *pdev)
/* Make sure we use pattern 0, 1 and not 4, 5 */
if (rp->quirks & rq6patterns)
- iowrite8(0x04, ioaddr + 0xA7);
+ iowrite8(0x04, ioaddr + WOLcgClr);
if (rp->wolopts & WAKE_MAGIC) {
iowrite8(WOLmagic, ioaddr + WOLcrSet);
diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
index fdc2367..19fd4cb 100644
--- a/drivers/net/virtio_net.c
+++ b/drivers/net/virtio_net.c
@@ -361,6 +361,7 @@ static int virtnet_probe(struct virtio_device *vdev)
netif_napi_add(dev, &vi->napi, virtnet_poll, napi_weight);
vi->dev = dev;
vi->vdev = vdev;
+ vdev->priv = vi;
/* We expect two virtqueues, receive then send. */
vi->rvq = vdev->config->find_vq(vdev, 0, skb_recv_done);
@@ -395,7 +396,6 @@ static int virtnet_probe(struct virtio_device *vdev)
}
pr_debug("virtnet: registered device %s\n", dev->name);
- vdev->priv = vi;
return 0;
unregister:
diff --git a/drivers/s390/net/claw.c b/drivers/s390/net/claw.c
index c307621..d8a5c22 100644
--- a/drivers/s390/net/claw.c
+++ b/drivers/s390/net/claw.c
@@ -1851,8 +1851,7 @@ claw_hw_tx(struct sk_buff *skb, struct net_device *dev, long linkid)
}
}
/* See how many write buffers are required to hold this data */
- numBuffers= ( skb->len + privptr->p_env->write_size - 1) /
- ( privptr->p_env->write_size);
+ numBuffers = DIV_ROUND_UP(skb->len, privptr->p_env->write_size);
/* If that number of buffers isn't available, give up for now */
if (privptr->write_free_count < numBuffers ||
@@ -2114,8 +2113,7 @@ init_ccw_bk(struct net_device *dev)
*/
ccw_blocks_perpage= PAGE_SIZE / CCWBK_SIZE;
ccw_pages_required=
- (ccw_blocks_required+ccw_blocks_perpage -1) /
- ccw_blocks_perpage;
+ DIV_ROUND_UP(ccw_blocks_required, ccw_blocks_perpage);
#ifdef DEBUGMSG
printk(KERN_INFO "%s: %s() > ccw_blocks_perpage=%d\n",
@@ -2131,30 +2129,29 @@ init_ccw_bk(struct net_device *dev)
* provide good performance. With packing buffers support 32k
* buffers are used.
*/
- if (privptr->p_env->read_size < PAGE_SIZE) {
- claw_reads_perpage= PAGE_SIZE / privptr->p_env->read_size;
- claw_read_pages= (privptr->p_env->read_buffers +
- claw_reads_perpage -1) / claw_reads_perpage;
+ if (privptr->p_env->read_size < PAGE_SIZE) {
+ claw_reads_perpage = PAGE_SIZE / privptr->p_env->read_size;
+ claw_read_pages = DIV_ROUND_UP(privptr->p_env->read_buffers,
+ claw_reads_perpage);
}
else { /* > or equal */
- privptr->p_buff_pages_perread=
- (privptr->p_env->read_size + PAGE_SIZE - 1) / PAGE_SIZE;
- claw_read_pages=
- privptr->p_env->read_buffers * privptr->p_buff_pages_perread;
+ privptr->p_buff_pages_perread =
+ DIV_ROUND_UP(privptr->p_env->read_size, PAGE_SIZE);
+ claw_read_pages = privptr->p_env->read_buffers *
+ privptr->p_buff_pages_perread;
}
if (privptr->p_env->write_size < PAGE_SIZE) {
- claw_writes_perpage=
- PAGE_SIZE / privptr->p_env->write_size;
- claw_write_pages=
- (privptr->p_env->write_buffers + claw_writes_perpage -1) /
- claw_writes_perpage;
+ claw_writes_perpage =
+ PAGE_SIZE / privptr->p_env->write_size;
+ claw_write_pages = DIV_ROUND_UP(privptr->p_env->write_buffers,
+ claw_writes_perpage);
}
else { /* > or equal */
- privptr->p_buff_pages_perwrite=
- (privptr->p_env->read_size + PAGE_SIZE - 1) / PAGE_SIZE;
- claw_write_pages=
- privptr->p_env->write_buffers * privptr->p_buff_pages_perwrite;
+ privptr->p_buff_pages_perwrite =
+ DIV_ROUND_UP(privptr->p_env->read_size, PAGE_SIZE);
+ claw_write_pages = privptr->p_env->write_buffers *
+ privptr->p_buff_pages_perwrite;
}
#ifdef DEBUGMSG
if (privptr->p_env->read_size < PAGE_SIZE) {
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/