Re: [PATCH] Input: edt-ft5x06 - Switch to newer gpio framework

[Franklin S Cooper Jr.]

Sorry ignoring this patch. Will resend with proper version 2 change information.

On 08/31/2015 06:17 PM, Franklin S Cooper Jr wrote:
> The current/old gpio framework used doesn't properly listen to
> ACTIVE_LOW and ACTIVE_HIGH flags. The newer gpio framework takes into
> account these flags when setting gpio values.
>
> Since the values being outputed were base on voltage and not logic the
> values being outputted must change to refect this difference. Also use
> gpiod_set_value_cansleep since wake and reset pins can be provided by
> bus based io expanders.
>
> Switch from msleep(5) to udelay_range(5000,6000) to avoid check patch
> warning.
>
> Signed-off-by: Franklin S Cooper Jr <fcooper@xxxxxx>
> ---
>  .../bindings/input/touchscreen/edt-ft5x06.txt      |   4 +-
>  drivers/input/touchscreen/edt-ft5x06.c             | 132 +++++++--------------
>  include/linux/input/edt-ft5x06.h                   |   4 +-
>  3 files changed, 47 insertions(+), 93 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> index 76db967..9330d4d 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> @@ -50,6 +50,6 @@ Example:
>  		pinctrl-0 = <&edt_ft5x06_pins>;
>  		interrupt-parent = <&gpio2>;
>  		interrupts = <5 0>;
> -		reset-gpios = <&gpio2 6 1>;
> -		wake-gpios = <&gpio4 9 0>;
> +		reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
> +		wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
>  	};
> diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> index 394b1de..d64d29a 100644
> --- a/drivers/input/touchscreen/edt-ft5x06.c
> +++ b/drivers/input/touchscreen/edt-ft5x06.c
> @@ -91,9 +91,9 @@ struct edt_ft5x06_ts_data {
>  	u16 num_x;
>  	u16 num_y;
>  
> -	int reset_pin;
> -	int irq_pin;
> -	int wake_pin;
> +	struct gpio_desc *reset_pin;
> +	struct gpio_desc *wake_pin;
> +	struct gpio_desc *irq_pin;
>  
>  #if defined(CONFIG_DEBUG_FS)
>  	struct dentry *debug_dir;
> @@ -752,45 +752,6 @@ edt_ft5x06_ts_teardown_debugfs(struct edt_ft5x06_ts_data *tsdata)
>  
>  #endif /* CONFIG_DEBUGFS */
>  
> -static int edt_ft5x06_ts_reset(struct i2c_client *client,
> -			struct edt_ft5x06_ts_data *tsdata)
> -{
> -	int error;
> -
> -	if (gpio_is_valid(tsdata->wake_pin)) {
> -		error = devm_gpio_request_one(&client->dev,
> -					tsdata->wake_pin, GPIOF_OUT_INIT_LOW,
> -					"edt-ft5x06 wake");
> -		if (error) {
> -			dev_err(&client->dev,
> -				"Failed to request GPIO %d as wake pin, error %d\n",
> -				tsdata->wake_pin, error);
> -			return error;
> -		}
> -
> -		msleep(5);
> -		gpio_set_value(tsdata->wake_pin, 1);
> -	}
> -	if (gpio_is_valid(tsdata->reset_pin)) {
> -		/* this pulls reset down, enabling the low active reset */
> -		error = devm_gpio_request_one(&client->dev,
> -					tsdata->reset_pin, GPIOF_OUT_INIT_LOW,
> -					"edt-ft5x06 reset");
> -		if (error) {
> -			dev_err(&client->dev,
> -				"Failed to request GPIO %d as reset pin, error %d\n",
> -				tsdata->reset_pin, error);
> -			return error;
> -		}
> -
> -		msleep(5);
> -		gpio_set_value(tsdata->reset_pin, 1);
> -		msleep(300);
> -	}
> -
> -	return 0;
> -}
> -
>  static int edt_ft5x06_ts_identify(struct i2c_client *client,
>  					struct edt_ft5x06_ts_data *tsdata,
>  					char *fw_version)
> @@ -931,30 +892,6 @@ edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
>  	}
>  }
>  
> -#ifdef CONFIG_OF
> -static int edt_ft5x06_i2c_ts_probe_dt(struct device *dev,
> -				struct edt_ft5x06_ts_data *tsdata)
> -{
> -	struct device_node *np = dev->of_node;
> -
> -	/*
> -	 * irq_pin is not needed for DT setup.
> -	 * irq is associated via 'interrupts' property in DT
> -	 */
> -	tsdata->irq_pin = -EINVAL;
> -	tsdata->reset_pin = of_get_named_gpio(np, "reset-gpios", 0);
> -	tsdata->wake_pin = of_get_named_gpio(np, "wake-gpios", 0);
> -
> -	return 0;
> -}
> -#else
> -static inline int edt_ft5x06_i2c_ts_probe_dt(struct device *dev,
> -					struct edt_ft5x06_ts_data *tsdata)
> -{
> -	return -ENODEV;
> -}
> -#endif
> -
>  static int edt_ft5x06_ts_probe(struct i2c_client *client,
>  					 const struct i2c_device_id *id)
>  {
> @@ -964,6 +901,7 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
>  	struct input_dev *input;
>  	int error;
>  	char fw_version[EDT_NAME_LEN];
> +	struct gpio_desc *gpio;
>  
>  	dev_dbg(&client->dev, "probing for EDT FT5x06 I2C\n");
>  
> @@ -973,32 +911,47 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
>  		return -ENOMEM;
>  	}
>  
> -	if (!pdata) {
> -		error = edt_ft5x06_i2c_ts_probe_dt(&client->dev, tsdata);
> -		if (error) {
> -			dev_err(&client->dev,
> -				"DT probe failed and no platform data present\n");
> -			return error;
> -		}
> -	} else {
> -		tsdata->reset_pin = pdata->reset_pin;
> -		tsdata->irq_pin = pdata->irq_pin;
> -		tsdata->wake_pin = -EINVAL;
> +	gpio = devm_gpiod_get_optional(&client->dev, "reset", GPIOD_OUT_HIGH);
> +	if (IS_ERR(gpio)) {
> +		error = PTR_ERR(gpio);
> +		dev_err(&client->dev,
> +			"Failed to request GPIO reset pin, error %d\n", error);
> +		return error;
>  	}
>  
> -	error = edt_ft5x06_ts_reset(client, tsdata);
> -	if (error)
> +	tsdata->reset_pin = gpio;
> +
> +	gpio = devm_gpiod_get_optional(&client->dev, "wake", GPIOD_OUT_LOW);
> +
> +	if (IS_ERR(gpio)) {
> +		error = PTR_ERR(gpio);
> +		dev_err(&client->dev,
> +			"Failed to request GPIO wake pin, error %d\n", error);
>  		return error;
> +	}
>  
> -	if (gpio_is_valid(tsdata->irq_pin)) {
> -		error = devm_gpio_request_one(&client->dev, tsdata->irq_pin,
> -					GPIOF_IN, "edt-ft5x06 irq");
> -		if (error) {
> -			dev_err(&client->dev,
> -				"Failed to request GPIO %d, error %d\n",
> -				tsdata->irq_pin, error);
> -			return error;
> -		}
> +	tsdata->wake_pin = gpio;
> +
> +	gpio = devm_gpiod_get_optional(&client->dev, "irq", GPIOD_IN);
> +
> +	if (IS_ERR(gpio)) {
> +		error = PTR_ERR(gpio);
> +		dev_err(&client->dev,
> +			"Failed to request GPIO irq pin, error %d\n", error);
> +		return error;
> +	}
> +
> +	tsdata->irq_pin = gpio;
> +
> +	if (tsdata->wake_pin) {
> +		usleep_range(5000, 6000);
> +		gpiod_set_value_cansleep(tsdata->wake_pin, 1);
> +	}
> +
> +	if (tsdata->reset_pin) {
> +		usleep_range(5000, 6000);
> +		gpiod_set_value_cansleep(tsdata->reset_pin, 0);
> +		msleep(300);
>  	}
>  
>  	input = devm_input_allocate_device(&client->dev);
> @@ -1074,7 +1027,8 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
>  
>  	dev_dbg(&client->dev,
>  		"EDT FT5x06 initialized: IRQ %d, WAKE pin %d, Reset pin %d.\n",
> -		client->irq, tsdata->wake_pin, tsdata->reset_pin);
> +		client->irq, desc_to_gpio(tsdata->wake_pin),
> +		desc_to_gpio(tsdata->reset_pin));
>  
>  	return 0;
>  
> diff --git a/include/linux/input/edt-ft5x06.h b/include/linux/input/edt-ft5x06.h
> index 8a1e0d1..058473a 100644
> --- a/include/linux/input/edt-ft5x06.h
> +++ b/include/linux/input/edt-ft5x06.h
> @@ -10,8 +10,8 @@
>   */
>  
>  struct edt_ft5x06_platform_data {
> -	int irq_pin;
> -	int reset_pin;
> +	int irq_gpio;
> +	int reset_gpio;
>  
>  	/* startup defaults for operational parameters */
>  	bool use_parameters;

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/