Re: [PATCH v9 1/5] Documentation: add sbsa-gwdt driver documentation

[Rob Herring]

On Mon, Nov 09, 2015 at 03:31:15PM +0800, fu.wei@xxxxxxxxxx wrote:
> From: Fu Wei <fu.wei@xxxxxxxxxx>
> 
> The sbsa-gwdt.txt documentation in devicetree/bindings/watchdog is for
> introducing SBSA(Server Base System Architecture) Generic Watchdog
> device node info into FDT.
> 
> Also add sbsa-gwdt introduction in watchdog-parameters.txt
> 
> Acked-by: Arnd Bergmann <arnd@xxxxxxxx>
> Signed-off-by: Fu Wei <fu.wei@xxxxxxxxxx>

Acked-by: Rob Herring <robh@xxxxxxxxxx>

> ---
>  .../devicetree/bindings/watchdog/sbsa-gwdt.txt     | 34 ++++++++++++++++++++++
>  Documentation/watchdog/watchdog-parameters.txt     |  6 ++++
>  2 files changed, 40 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/watchdog/sbsa-gwdt.txt b/Documentation/devicetree/bindings/watchdog/sbsa-gwdt.txt
> new file mode 100644
> index 0000000..2da63db
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/watchdog/sbsa-gwdt.txt
> @@ -0,0 +1,34 @@
> +* SBSA (Server Base System Architecture) Generic Watchdog
> +
> +The SBSA Generic Watchdog Timer is used to force a reset of the system
> +after two stages of timeout have elapsed.  A detailed definition of the
> +watchdog timer can be found in the ARM document: ARM-DEN-0029 - Server
> +Base System Architecture (SBSA)
> +
> +Required properties:
> +- compatible: Should at least contain "arm,sbsa-gwdt".
> +
> +- reg: Each entry specifies the base physical address of a register frame
> +  and the length of that frame; currently, two frames must be defined,
> +  in this order:
> +  1: Watchdog control frame;
> +  2: Refresh frame.
> +
> +- interrupts: Should contain the Watchdog Signal 0 (WS0) SPI (Shared
> +  Peripheral Interrupt) number of SBSA Generic Watchdog.
> +
> +Optional properties
> +- timeout-sec: Watchdog timeout and pre-timeout values.
> +  If used, at least first timeout value (in seconds) must be provided.
> +  A second optional value (in seconds) may also be provided and
> +  will be used as the pre-timeout value, if it is given.
> +
> +Example for FVP Foundation Model v8:
> +
> +watchdog@2a440000 {
> +	compatible = "arm,sbsa-gwdt";
> +	reg = <0x0 0x2a440000 0 0x1000>,
> +	      <0x0 0x2a450000 0 0x1000>;
> +	interrupts = <0 27 4>;
> +	timeout-sec = <60 30>;
> +};
> diff --git a/Documentation/watchdog/watchdog-parameters.txt b/Documentation/watchdog/watchdog-parameters.txt
> index 9f9ec9f..e62c8c4 100644
> --- a/Documentation/watchdog/watchdog-parameters.txt
> +++ b/Documentation/watchdog/watchdog-parameters.txt
> @@ -284,6 +284,12 @@ sbc_fitpc2_wdt:
>  margin: Watchdog margin in seconds (default 60s)
>  nowayout: Watchdog cannot be stopped once started
>  -------------------------------------------------
> +sbsa_gwdt:
> +timeout: Watchdog timeout in seconds. (default 60s)
> +pretimeout: Watchdog pretimeout in seconds. (default 30s)
> +nowayout: Watchdog cannot be stopped once started
> +	(default=kernel config parameter)
> +-------------------------------------------------
>  sc1200wdt:
>  isapnp: When set to 0 driver ISA PnP support will be disabled (default=1)
>  io: io port
> -- 
> 2.5.0
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/