Re: [PATCH v2] iio: Add IIO support for the DAC on the Apex Embedded Systems STX104
From: William Breathitt Gray
Date: Wed Feb 10 2016 - 16:22:52 EST
On Wed, Feb 10, 2016 at 06:55:45PM +0000, Jonathan Cameron wrote:
>On 10/02/16 02:19, William Breathitt Gray wrote:
>> On Tue, Feb 09, 2016 at 10:37:09PM +0000, Jonathan Cameron wrote:
>>> My only real question is on the naming of the module parameter.
>>> Is it the equivalent of the io address that a load of ISA
>>> radio drivers seem to use? (fed to me by grepping isa_register_driver)
>>> If so perhaps that's the 'standard' name as much as one exists for this?
>>
>> Yes, you noted correctly that the stx104_base module parameter fulfills
>> the same function as the io module parameter used in many of the radio
>> drivers: it's an array holding the io port address of each device.
>> However, I find "io" to be a rather vague module parameter name, so I've
>> decided to use the more apt "stx104_base" name for my array of base
>> addresses.
>>
>> As you've probably noticed, there are few ISA drivers existing in the
>> kernel baseline currently, so not much of a standard is set yet. I'm all
>> right with renaming the module parameter if you have a preference, just
>> as long as the name is more informative than simply "io."
>>
>> For what it's worth, this driver is part of a series of PC/104 drivers
>> I've been submitting to various subsystems (in the hopes of improving
>> the lack of PC/104 support in the baseline Linux kernel); see
>> drivers/gpio/gpio-104-idio-16.c and drivers/gpio/gpio-104-idi-48.c for
>> example. I have thus far been following the convention of naming the
>> base address module parameter as "modname_base," where "modname" is the
>> respective module name.
>I've been trying to work out if IO ports is a generic enough ISA term
>to take the view that anyone using an ISA card should know about it...
>I certainly know the I/O space approach to interacting with PCI cards is
>well understood in people working with shall we say 'dumb' PCI hardware.
>
>I guess I don't really care all that much on this though - just nice to
>be consistent / general when possible.
I believe that port-mapped I/O is ubiquitous enough in the industry that
anyone with an ISA card will understand the term; in fact, I can't
recall any PC/104 card datasheet I've encountered without a chapter
section devoted to "I/O port address" configuration.
The ISA drivers in the sound subsystem use "port" as the module
parameter name for the I/O port base address of the respective sound
device. Notice also how there are module parameters such as "midi_port"
which represent the I/O port address of various registers on the device.
"I/O port address" does not necessarily mean the base address of the
device, but simply a port address (typically pointing to a particular
register). For this reason, I prefer the more specific name "base" to
indicate the I/O port base address of the device from which to derive
the register addresses.
Thinking it over again, I want to submit a version 3 of this patch which
will rename "stx104_base" to the more general "base" name; the "stx104_"
prefix is overly verbose for a module parameter since the user should
already know the module he/she is configuring. Hopefully, by using a
more general name, there will also arise a more consistent way of
configuring the I/O port base addresses among other PC/104 and ISA
drivers via the "base" module parameter.
Are there any other changes I should include in version 3?
On an unrelated note, I may write a patch in the future to add support
for the 16-channel ADC on the STX104. Should this support be added into
this existing iio/dac/stx104.c file, or into a new iio/adc/stx104.c
file?
William Breathitt Gray