Re: [PATCH [RFC]] PCI: hv: add explicit fencing to config space access

[Bjorn Helgaas]

On Tue, May 03, 2016 at 02:22:00PM +0200, Vitaly Kuznetsov wrote:
> I'm trying to pass-through Broadcom BCM5720 NIC (Dell Device 1f5b) on Dell
> R720 server. Everything works fine when target VM has only one CPU, but
> SMP guests reboot when NIC driver is trying to access PCI config space
> (with  hv_pcifront_read_config/hv_pcifront_write_config). The reboot
> appears to be induced by the hypervisor and no crash is observed. Windows
> event logs are not helpful at all ('Virtual machine ... has quit
> unexpectedly'). The particular access point is always different and
> putting debug between them (printk/mdelay/...) moves the issue further
> away. The server model affects the issue as well: on Dell R420 I'm able to
> pass-through BCM5720 NIC to SMP guests without issues.
> 
> While I'm obviously failing to reveal the essence of the issue I was able
> to come up with a (possible) solution: if explicit fencing is put to
> hv_pcifront_read_config/hv_pcifront_write_config the issue goes away. The
> essential minimum is rmb() at the end on _hv_pcifront_read_config() and
> wmb() at the end of _hv_pcifront_write_config() but I'm not confident it
> will be sufficient for all hardware. I suggest the following fencing:
> 1) wmb()/mb() between choosing the function and writing to its space.
> 2) mb() before releasing the spinlock in both _hv_pcifront_read_config()/
>    _hv_pcifront_write_config to ensure that consecutive reads/writes to
>   the space won't get re-ordered as drivers may count on that.
> Config space access is not supposed to be performance-critical so this
> explicit fencing is not supposed to bring any slowdown.
> 
> Signed-off-by: Vitaly Kuznetsov <vkuznets@xxxxxxxxxx>

Applied with Jake's ack to pci/host-hv for v4.7, thanks, Vitaly.

I changed "fence" to "barrier" in the changelog to follow the
common Linux terminology.

> ---
>  drivers/pci/host/pci-hyperv.c | 14 ++++++++++++++
>  1 file changed, 14 insertions(+)
> 
> diff --git a/drivers/pci/host/pci-hyperv.c b/drivers/pci/host/pci-hyperv.c
> index c17e792..7e9b2de 100644
> --- a/drivers/pci/host/pci-hyperv.c
> +++ b/drivers/pci/host/pci-hyperv.c
> @@ -553,6 +553,8 @@ static void _hv_pcifront_read_config(struct hv_pci_dev *hpdev, int where,
>  		spin_lock_irqsave(&hpdev->hbus->config_lock, flags);
>  		/* Choose the function to be read. (See comment above) */
>  		writel(hpdev->desc.win_slot.slot, hpdev->hbus->cfg_addr);
> +		/* Make sure the function was chosen before we start reading. */
> +		mb();
>  		/* Read from that function's config space. */
>  		switch (size) {
>  		case 1:
> @@ -565,6 +567,11 @@ static void _hv_pcifront_read_config(struct hv_pci_dev *hpdev, int where,
>  			*val = readl(addr);
>  			break;
>  		}
> +		/*
> +		 * Make sure the write was done before we release the spinlock
> +		 * allowing consecutive reads/writes.
> +		 */
> +		mb();
>  		spin_unlock_irqrestore(&hpdev->hbus->config_lock, flags);
>  	} else {
>  		dev_err(&hpdev->hbus->hdev->device,
> @@ -592,6 +599,8 @@ static void _hv_pcifront_write_config(struct hv_pci_dev *hpdev, int where,
>  		spin_lock_irqsave(&hpdev->hbus->config_lock, flags);
>  		/* Choose the function to be written. (See comment above) */
>  		writel(hpdev->desc.win_slot.slot, hpdev->hbus->cfg_addr);
> +		/* Make sure the function was chosen before we start writing. */
> +		wmb();
>  		/* Write to that function's config space. */
>  		switch (size) {
>  		case 1:
> @@ -604,6 +613,11 @@ static void _hv_pcifront_write_config(struct hv_pci_dev *hpdev, int where,
>  			writel(val, addr);
>  			break;
>  		}
> +		/*
> +		 * Make sure the write was done before we release the spinlock
> +		 * allowing consecutive reads/writes.
> +		 */
> +		mb();
>  		spin_unlock_irqrestore(&hpdev->hbus->config_lock, flags);
>  	} else {
>  		dev_err(&hpdev->hbus->hdev->device,
> -- 
> 2.5.5
>