Re: [PATCH 2/3] clk: hisilicon: add CRG driver for Hi3516CV300 SoC

[Rob Herring]

On Mon, Oct 17, 2016 at 08:07:04PM +0800, Pan Wen wrote:
> Add CRG driver for Hi3516CV300 SoC. CRG(Clock and Reset
> Generator) module generates clock and reset signals used
> by other module blocks on SoC.
> 
> Signed-off-by: Pan Wen <wenpan@xxxxxxxxxxxxx>
> ---
>  .../devicetree/bindings/clock/hisi-crg.txt         |  50 ++++
>  drivers/clk/hisilicon/Kconfig                      |   8 +
>  drivers/clk/hisilicon/Makefile                     |   1 +
>  drivers/clk/hisilicon/crg-hi3516cv300.c            | 330 +++++++++++++++++++++
>  drivers/clk/hisilicon/crg.h                        |  34 +++
>  include/dt-bindings/clock/hi3516cv300-clock.h      |  48 +++
>  6 files changed, 471 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/clock/hisi-crg.txt
>  create mode 100644 drivers/clk/hisilicon/crg-hi3516cv300.c
>  create mode 100644 drivers/clk/hisilicon/crg.h
>  create mode 100644 include/dt-bindings/clock/hi3516cv300-clock.h
> 
> diff --git a/Documentation/devicetree/bindings/clock/hisi-crg.txt b/Documentation/devicetree/bindings/clock/hisi-crg.txt
> new file mode 100644
> index 0000000..cc60b3d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/clock/hisi-crg.txt
> @@ -0,0 +1,50 @@
> +* HiSilicon Clock and Reset Generator(CRG)

Seems kind of generic given there's already various HiSi clock bindings 
documented.

> +
> +The CRG module provides clock and reset signals to various
> +modules within the SoC.
> +
> +This binding uses the following bindings:
> +    Documentation/devicetree/bindings/clock/clock-bindings.txt
> +    Documentation/devicetree/bindings/reset/reset.txt
> +
> +Required Properties:
> +
> +- compatible: should be one of the following.
> +  - "hisilicon,hi3516cv300-crg"
> +  - "hisilicon,hi3516cv300-sysctrl"
> +  - "hisilicon,hi3519-crg"

There is already a binding for this. Please merge them.

> +  - "hisilicon,hi3798cv200-crg"
> +  - "hisilicon,hi3798cv200-sysctrl"
> +
> +- reg: physical base address of the controller and length of memory mapped
> +  region.
> +
> +- #clock-cells: should be 1.
> +
> +Each clock is assigned an identifier and client nodes use this identifier
> +to specify the clock which they consume.
> +
> +All these identifier could be found in <dt-bindings/clock/hi3519-clock.h>.
> +
> +- #reset-cells: should be 2.
> +
> +A reset signal can be controlled by writing a bit register in the CRG module.
> +The reset specifier consists of two cells. The first cell represents the
> +register offset relative to the base address. The second cell represents the
> +bit index in the register.
> +
> +Example: CRG nodes
> +CRG: clock-reset-controller@12010000 {
> +	compatible = "hisilicon,hi3519-crg";
> +	reg = <0x12010000 0x10000>;
> +	#clock-cells = <1>;
> +	#reset-cells = <2>;
> +};
> +
> +Example: consumer nodes
> +i2c0: i2c@12110000 {
> +	compatible = "hisilicon,hi3519-i2c";
> +	reg = <0x12110000 0x1000>;
> +	clocks = <&CRG HI3519_I2C0_RST>;
> +	resets = <&CRG 0xe4 0>;
> +};