Re: [PATCH v3] pinctrl: Add SX150X GPIO Extender Pinctrl Driver

From: Neil Armstrong
Date: Fri Oct 21 2016 - 05:39:44 EST

On 10/21/2016 11:09 AM, Neil Armstrong wrote:
> Since the I2C sx150x GPIO expander driver uses platform_data to manage
> the pins configurations, rewrite the driver as a pinctrl driver using
> pinconf to get/set pin configurations from DT or debugfs.
>
> The pinctrl driver is functionnally equivalent as the gpio-only driver
> and can use DT for pinconf. The platform_data confirmation is dropped.
>
> This patchset removed the gpio-only driver and selects the Pinctrl driver
> config instead. This patchset also migrates the gpio dt-bindings to pinctrl
> and add the pinctrl optional properties.
>
> The driver was tested with a SX1509 device on a BeagleBone black with
> interrupt support and on an X86_64 machine over an I2C to USB converter.
>
> Signed-off-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx>

Forgot to add :

Tested-by: Peter Rosin <peda@xxxxxxxxxx>
Acked-by: Rob Herring <robh@xxxxxxxxxx>

reported on the v2 patch.

> ---
> This is a fixed version that builds and runs on non-OF platforms and on
> arm based OF. The GPIO version is removed and the bindings are also moved
> to the pinctrl bindings.
>
> Changes since v2 at http://lkml.kernel.org/r/1474991325-1754-1-git-send-email-narmstrong@xxxxxxxxxxxx:
> - rebased on v4.9-rc1
> - removed MODULE_DEVICE_TABLE as in upstream bb411e771b0e [1]
>
> Changes since v1 at http://lkml.kernel.org/r/1473166599-29266-1-git-send-email-narmstrong@xxxxxxxxxxxx:
> - Fix Kconfig descriptions on pinctrl and gpio
> - Fix Kconfig dependency
> - Remove oscio support for non-789 devices
> - correct typo in dt bindings
> - remove probe reset for non-789 devices
>
> Changes since RFC at http://lkml.kernel.org/r/1472130692-14404-1-git-send-email-narmstrong@xxxxxxxxxxxx:
> - Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms
> - No more rely on OF_GPIO config
> - Moved and enhanced bindings to pinctrl bindings
> - Removed gpio-sx150x.c
> - Temporary select PINCTRL_SX150X when GPIO_SX150X
> - Temporary mark GPIO_SX150X as deprecated
>
> [1] gpio: sx150x: fix implicit assumption module.h is present
>
> .../gpio-sx150x.txt => pinctrl/pinctrl-sx150x.txt} | 46 +-
> drivers/gpio/Kconfig | 13 +-
> drivers/gpio/Makefile | 1 -
> drivers/pinctrl/Kconfig | 14 +
> drivers/pinctrl/Makefile | 1 +
> .../gpio-sx150x.c => pinctrl/pinctrl-sx150x.c} | 1174 ++++++++++++--------
> 6 files changed, 779 insertions(+), 470 deletions(-)
> rename Documentation/devicetree/bindings/{gpio/gpio-sx150x.txt => pinctrl/pinctrl-sx150x.txt} (40%)
> rename drivers/{gpio/gpio-sx150x.c => pinctrl/pinctrl-sx150x.c} (23%)
>
> diff --git a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt
> similarity index 40%
> rename from Documentation/devicetree/bindings/gpio/gpio-sx150x.txt
> rename to Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt
> index c809acb..c293c8a 100644
> --- a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt
> @@ -1,34 +1,54 @@
> SEMTECH SX150x GPIO expander bindings
>
> +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and
> +../interrupt-controller/interrupts.txt for generic information regarding
> +pin controller, GPIO, and interrupt bindings.
>
> Required properties:
> -
> -- compatible: should be "semtech,sx1506q",
> +- compatible: should be one of :
> + "semtech,sx1506q",
> "semtech,sx1508q",
> "semtech,sx1509q",
> "semtech,sx1502q".
>
> - reg: The I2C slave address for this device.
>
> -- interrupt-parent: phandle of the parent interrupt controller.
> -
> -- interrupts: Interrupt specifier for the controllers interrupt.
> -
> - #gpio-cells: Should be 2. The first cell is the GPIO number and the
> second cell is used to specify optional parameters:
> bit 0: polarity (0: normal, 1: inverted)
>
> - gpio-controller: Marks the device as a GPIO controller.
>
> +Optional properties :
> +- interrupt-parent: phandle of the parent interrupt controller.
> +
> +- interrupts: Interrupt specifier for the controllers interrupt.
> +
> - interrupt-controller: Marks the device as a interrupt controller.
>
> +- semtech,probe-reset: Will trigger a reset of the GPIO expander on probe,
> + only for sx1508q and sx1509q
> +
> The GPIO expander can optionally be used as an interrupt controller, in
> -which case it uses the default two cell specifier as described in
> -Documentation/devicetree/bindings/interrupt-controller/interrupts.txt.
> +which case it uses the default two cell specifier.
> +
> +Required properties for pin configuration sub-nodes:
> + - pins: List of pins to which the configuration applies.
> +
> +Optional properties for pin configuration sub-nodes:
> +----------------------------------------------------
> + - bias-disable: disable any pin bias, except the OSCIO pin
> + - bias-pull-up: pull up the pin, except the OSCIO pin
> + - bias-pull-down: pull down the pin, except the OSCIO pin
> + - bias-pull-pin-default: use pin-default pull state, except the OSCIO pin
> + - drive-push-pull: drive actively high and low
> + - drive-open-drain: drive with open drain only for sx1508q and sx1509q and except the OSCIO pin
> + - output-low: set the pin to output mode with low level
> + - output-high: set the pin to output mode with high level
>
> Example:
>
> - i2c_gpio_expander@20{
> + i2c0gpio-expander@20{
> #gpio-cells = <2>;
> #interrupt-cells = <2>;
> compatible = "semtech,sx1506q";
> @@ -38,4 +58,12 @@ Example:
>
> gpio-controller;
> interrupt-controller;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&gpio1_cfg_pins>;
> +
> + gpio1_cfg_pins: gpio1-cfg {
> + pins = "gpio1";
> + bias-pull-up;
> + };
> };
> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> index 26ee00f..db3f7aa 100644
> --- a/drivers/gpio/Kconfig
> +++ b/drivers/gpio/Kconfig
> @@ -781,16 +781,13 @@ config GPIO_PCF857X
> platform-neutral GPIO calls.
>
> config GPIO_SX150X
> - bool "Semtech SX150x I2C GPIO expander"
> - depends on I2C=y
> - select GPIOLIB_IRQCHIP
> + bool "Semtech SX150x I2C GPIO expander (deprecated)"
> + depends on PINCTRL && I2C=y
> + select PINCTRL_SX150X
> default n
> help
> - Say yes here to provide support for Semtech SX150-series I2C
> - GPIO expanders. Compatible models include:
> -
> - 8 bits: sx1508q
> - 16 bits: sx1509q
> + Say yes here to provide support for Semtech SX150x-series I2C
> + GPIO expanders. The GPIO driver was replaced by a Pinctrl version.
>
> config GPIO_TPIC2810
> tristate "TPIC2810 8-Bit I2C GPO expander"
> diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> index ab28a2d..76c7af6 100644
> --- a/drivers/gpio/Makefile
> +++ b/drivers/gpio/Makefile
> @@ -102,7 +102,6 @@ obj-$(CONFIG_GPIO_SPEAR_SPICS) += gpio-spear-spics.o
> obj-$(CONFIG_GPIO_STA2X11) += gpio-sta2x11.o
> obj-$(CONFIG_GPIO_STMPE) += gpio-stmpe.o
> obj-$(CONFIG_GPIO_STP_XWAY) += gpio-stp-xway.o
> -obj-$(CONFIG_GPIO_SX150X) += gpio-sx150x.o
> obj-$(CONFIG_GPIO_SYSCON) += gpio-syscon.o
> obj-$(CONFIG_GPIO_TB10X) += gpio-tb10x.o
> obj-$(CONFIG_GPIO_TC3589X) += gpio-tc3589x.o
> diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
> index 0e75d94..801fa8b 100644
> --- a/drivers/pinctrl/Kconfig
> +++ b/drivers/pinctrl/Kconfig
> @@ -164,6 +164,20 @@ config PINCTRL_SIRF
> select GENERIC_PINCONF
> select GPIOLIB_IRQCHIP
>
> +config PINCTRL_SX150X
> + bool "Semtech SX150x I2C GPIO expander pinctrl driver"
> + depends on GPIOLIB && I2C=y
> + select PINMUX
> + select PINCONF
> + select GENERIC_PINCONF
> + select GPIOLIB_IRQCHIP
> + help
> + Say yes here to provide support for Semtech SX150x-series I2C
> + GPIO expanders as pinctrl module.
> + Compatible models include:
> + - 8 bits: sx1508q, sx1502q
> + - 16 bits: sx1509q, sx1506q
> +
> config PINCTRL_PISTACHIO
> def_bool y if MACH_PISTACHIO
> depends on GPIOLIB
> diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
> index 11bad37..3b8e6f7 100644
> --- a/drivers/pinctrl/Makefile
> +++ b/drivers/pinctrl/Makefile
> @@ -25,6 +25,7 @@ obj-$(CONFIG_PINCTRL_PISTACHIO) += pinctrl-pistachio.o
> obj-$(CONFIG_PINCTRL_ROCKCHIP) += pinctrl-rockchip.o
> obj-$(CONFIG_PINCTRL_SINGLE) += pinctrl-single.o
> obj-$(CONFIG_PINCTRL_SIRF) += sirf/
> +obj-$(CONFIG_PINCTRL_SX150X) += pinctrl-sx150x.o
> obj-$(CONFIG_ARCH_TEGRA) += tegra/
> obj-$(CONFIG_PINCTRL_TZ1090) += pinctrl-tz1090.o
> obj-$(CONFIG_PINCTRL_TZ1090_PDC) += pinctrl-tz1090-pdc.o
> diff --git a/drivers/gpio/gpio-sx150x.c b/drivers/pinctrl/pinctrl-sx150x.c
> similarity index 23%
> rename from drivers/gpio/gpio-sx150x.c
> rename to drivers/pinctrl/pinctrl-sx150x.c
> index af95de8..e985471 100644
> --- a/drivers/gpio/gpio-sx150x.c
> +++ b/drivers/pinctrl/pinctrl-sx150x.c
> @@ -1,4 +1,8 @@
> -/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
> +/*
> + * Copyright (c) 2016, BayLibre, SAS. All rights reserved.
> + * Author: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
> + *
> + * Copyright (c) 2010, Code Aurora Forum. All rights reserved.
> *
> * Driver for Semtech SX150X I2C GPIO Expanders
> *
> @@ -12,13 +16,8 @@
> * but WITHOUT ANY WARRANTY; without even the implied warranty of
> * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> * GNU General Public License for more details.
> - *
> - * You should have received a copy of the GNU General Public License
> - * along with this program; if not, write to the Free Software
> - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
> - * 02110-1301, USA.
> */
> -#include <linux/gpio.h>
> +
> #include <linux/i2c.h>
> #include <linux/init.h>
> #include <linux/interrupt.h>
> @@ -26,17 +25,23 @@
> #include <linux/mutex.h>
> #include <linux/slab.h>
> #include <linux/of.h>
> -#include <linux/of_address.h>
> -#include <linux/of_irq.h>
> -#include <linux/of_gpio.h>
> -#include <linux/of_device.h>
> +#include <linux/gpio.h>
> +#include <linux/pinctrl/machine.h>
> +#include <linux/pinctrl/pinconf.h>
> +#include <linux/pinctrl/pinctrl.h>
> +#include <linux/pinctrl/pinmux.h>
> +#include <linux/pinctrl/pinconf-generic.h>
>
> -#define NO_UPDATE_PENDING -1
> +#include "core.h"
> +#include "pinconf.h"
> +#include "pinctrl-utils.h"
>
> /* The chip models of sx150x */
> -#define SX150X_123 0
> -#define SX150X_456 1
> -#define SX150X_789 2
> +enum {
> + SX150X_123 = 0,
> + SX150X_456,
> + SX150X_789,
> +};
>
> struct sx150x_123_pri {
> u8 reg_pld_mode;
> @@ -82,167 +87,146 @@ struct sx150x_device_data {
> struct sx150x_456_pri x456;
> struct sx150x_789_pri x789;
> } pri;
> + const struct pinctrl_pin_desc *pins;
> + unsigned int npins;
> };
>
> -/**
> - * struct sx150x_platform_data - config data for SX150x driver
> - * @gpio_base: The index number of the first GPIO assigned to this
> - * GPIO expander. The expander will create a block of
> - * consecutively numbered gpios beginning at the given base,
> - * with the size of the block depending on the model of the
> - * expander chip.
> - * @oscio_is_gpo: If set to true, the driver will configure OSCIO as a GPO
> - * instead of as an oscillator, increasing the size of the
> - * GP(I)O pool created by this expander by one. The
> - * output-only GPO pin will be added at the end of the block.
> - * @io_pullup_ena: A bit-mask which enables or disables the pull-up resistor
> - * for each IO line in the expander. Setting the bit at
> - * position n will enable the pull-up for the IO at
> - * the corresponding offset. For chips with fewer than
> - * 16 IO pins, high-end bits are ignored.
> - * @io_pulldn_ena: A bit-mask which enables-or disables the pull-down
> - * resistor for each IO line in the expander. Setting the
> - * bit at position n will enable the pull-down for the IO at
> - * the corresponding offset. For chips with fewer than
> - * 16 IO pins, high-end bits are ignored.
> - * @io_polarity: A bit-mask which enables polarity inversion for each IO line
> - * in the expander. Setting the bit at position n inverts
> - * the polarity of that IO line, while clearing it results
> - * in normal polarity. For chips with fewer than 16 IO pins,
> - * high-end bits are ignored.
> - * @irq_summary: The 'summary IRQ' line to which the GPIO expander's INT line
> - * is connected, via which it reports interrupt events
> - * across all GPIO lines. This must be a real,
> - * pre-existing IRQ line.
> - * Setting this value < 0 disables the irq_chip functionality
> - * of the driver.
> - * @irq_base: The first 'virtual IRQ' line at which our block of GPIO-based
> - * IRQ lines will appear. Similarly to gpio_base, the expander
> - * will create a block of irqs beginning at this number.
> - * This value is ignored if irq_summary is < 0.
> - * @reset_during_probe: If set to true, the driver will trigger a full
> - * reset of the chip at the beginning of the probe
> - * in order to place it in a known state.
> - */
> -struct sx150x_platform_data {
> - unsigned gpio_base;
> - bool oscio_is_gpo;
> - u16 io_pullup_ena;
> - u16 io_pulldn_ena;
> - u16 io_polarity;
> - int irq_summary;
> - unsigned irq_base;
> - bool reset_during_probe;
> +struct sx150x_pinctrl {
> + struct device *dev;
> + struct i2c_client *client;
> + struct pinctrl_dev *pctldev;
> + struct pinctrl_desc pinctrl_desc;
> + struct gpio_chip gpio;
> + struct irq_chip irq_chip;
> + struct {
> + int update;
> + u32 sense;
> + u32 masked;
> + u32 dev_sense;
> + u32 dev_masked;
> + } irq;
> + struct mutex lock;
> + const struct sx150x_device_data *data;
> };
>
> -struct sx150x_chip {
> - struct gpio_chip gpio_chip;
> - struct i2c_client *client;
> - const struct sx150x_device_data *dev_cfg;
> - int irq_summary;
> - int irq_base;
> - int irq_update;
> - u32 irq_sense;
> - u32 irq_masked;
> - u32 dev_sense;
> - u32 dev_masked;
> - struct irq_chip irq_chip;
> - struct mutex lock;
> +static const struct pinctrl_pin_desc sx150x_8_pins[] = {
> + PINCTRL_PIN(0, "gpio0"),
> + PINCTRL_PIN(1, "gpio1"),
> + PINCTRL_PIN(2, "gpio2"),
> + PINCTRL_PIN(3, "gpio3"),
> + PINCTRL_PIN(4, "gpio4"),
> + PINCTRL_PIN(5, "gpio5"),
> + PINCTRL_PIN(6, "gpio6"),
> + PINCTRL_PIN(7, "gpio7"),
> + PINCTRL_PIN(8, "oscio"),
> };
>
> -static const struct sx150x_device_data sx150x_devices[] = {
> - [0] = { /* sx1508q */
> - .model = SX150X_789,
> - .reg_pullup = 0x03,
> - .reg_pulldn = 0x04,
> - .reg_dir = 0x07,
> - .reg_data = 0x08,
> - .reg_irq_mask = 0x09,
> - .reg_irq_src = 0x0c,
> - .reg_sense = 0x0b,
> - .pri.x789 = {
> - .reg_drain = 0x05,
> - .reg_polarity = 0x06,
> - .reg_clock = 0x0f,
> - .reg_misc = 0x10,
> - .reg_reset = 0x7d,
> - },
> - .ngpios = 8,
> - },
> - [1] = { /* sx1509q */
> - .model = SX150X_789,
> - .reg_pullup = 0x07,
> - .reg_pulldn = 0x09,
> - .reg_dir = 0x0f,
> - .reg_data = 0x11,
> - .reg_irq_mask = 0x13,
> - .reg_irq_src = 0x19,
> - .reg_sense = 0x17,
> - .pri.x789 = {
> - .reg_drain = 0x0b,
> - .reg_polarity = 0x0d,
> - .reg_clock = 0x1e,
> - .reg_misc = 0x1f,
> - .reg_reset = 0x7d,
> - },
> - .ngpios = 16
> - },
> - [2] = { /* sx1506q */
> - .model = SX150X_456,
> - .reg_pullup = 0x05,
> - .reg_pulldn = 0x07,
> - .reg_dir = 0x03,
> - .reg_data = 0x01,
> - .reg_irq_mask = 0x09,
> - .reg_irq_src = 0x0f,
> - .reg_sense = 0x0d,
> - .pri.x456 = {
> - .reg_pld_mode = 0x21,
> - .reg_pld_table0 = 0x23,
> - .reg_pld_table1 = 0x25,
> - .reg_pld_table2 = 0x27,
> - .reg_pld_table3 = 0x29,
> - .reg_pld_table4 = 0x2b,
> - .reg_advance = 0xad,
> - },
> - .ngpios = 16
> +static const struct pinctrl_pin_desc sx150x_16_pins[] = {
> + PINCTRL_PIN(0, "gpio0"),
> + PINCTRL_PIN(1, "gpio1"),
> + PINCTRL_PIN(2, "gpio2"),
> + PINCTRL_PIN(3, "gpio3"),
> + PINCTRL_PIN(4, "gpio4"),
> + PINCTRL_PIN(5, "gpio5"),
> + PINCTRL_PIN(6, "gpio6"),
> + PINCTRL_PIN(7, "gpio7"),
> + PINCTRL_PIN(8, "gpio8"),
> + PINCTRL_PIN(9, "gpio9"),
> + PINCTRL_PIN(10, "gpio10"),
> + PINCTRL_PIN(11, "gpio11"),
> + PINCTRL_PIN(12, "gpio12"),
> + PINCTRL_PIN(13, "gpio13"),
> + PINCTRL_PIN(14, "gpio14"),
> + PINCTRL_PIN(15, "gpio15"),
> + PINCTRL_PIN(16, "oscio"),
> +};
> +
> +static const struct sx150x_device_data sx1508q_device_data = {
> + .model = SX150X_789,
> + .reg_pullup = 0x03,
> + .reg_pulldn = 0x04,
> + .reg_dir = 0x07,
> + .reg_data = 0x08,
> + .reg_irq_mask = 0x09,
> + .reg_irq_src = 0x0c,
> + .reg_sense = 0x0b,
> + .pri.x789 = {
> + .reg_drain = 0x05,
> + .reg_polarity = 0x06,
> + .reg_clock = 0x0f,
> + .reg_misc = 0x10,
> + .reg_reset = 0x7d,
> },
> - [3] = { /* sx1502q */
> - .model = SX150X_123,
> - .reg_pullup = 0x02,
> - .reg_pulldn = 0x03,
> - .reg_dir = 0x01,
> - .reg_data = 0x00,
> - .reg_irq_mask = 0x05,
> - .reg_irq_src = 0x08,
> - .reg_sense = 0x07,
> - .pri.x123 = {
> - .reg_pld_mode = 0x10,
> - .reg_pld_table0 = 0x11,
> - .reg_pld_table1 = 0x12,
> - .reg_pld_table2 = 0x13,
> - .reg_pld_table3 = 0x14,
> - .reg_pld_table4 = 0x15,
> - .reg_advance = 0xad,
> - },
> - .ngpios = 8,
> + .ngpios = 8,
> + .pins = sx150x_8_pins,
> + .npins = ARRAY_SIZE(sx150x_8_pins),
> +};
> +
> +static const struct sx150x_device_data sx1509q_device_data = {
> + .model = SX150X_789,
> + .reg_pullup = 0x07,
> + .reg_pulldn = 0x09,
> + .reg_dir = 0x0f,
> + .reg_data = 0x11,
> + .reg_irq_mask = 0x13,
> + .reg_irq_src = 0x19,
> + .reg_sense = 0x17,
> + .pri.x789 = {
> + .reg_drain = 0x0b,
> + .reg_polarity = 0x0d,
> + .reg_clock = 0x1e,
> + .reg_misc = 0x1f,
> + .reg_reset = 0x7d,
> },
> + .ngpios = 16,
> + .pins = sx150x_16_pins,
> + .npins = ARRAY_SIZE(sx150x_16_pins),
> };
>
> -static const struct i2c_device_id sx150x_id[] = {
> - {"sx1508q", 0},
> - {"sx1509q", 1},
> - {"sx1506q", 2},
> - {"sx1502q", 3},
> - {}
> +static const struct sx150x_device_data sx1506q_device_data = {
> + .model = SX150X_456,
> + .reg_pullup = 0x05,
> + .reg_pulldn = 0x07,
> + .reg_dir = 0x03,
> + .reg_data = 0x01,
> + .reg_irq_mask = 0x09,
> + .reg_irq_src = 0x0f,
> + .reg_sense = 0x0d,
> + .pri.x456 = {
> + .reg_pld_mode = 0x21,
> + .reg_pld_table0 = 0x23,
> + .reg_pld_table1 = 0x25,
> + .reg_pld_table2 = 0x27,
> + .reg_pld_table3 = 0x29,
> + .reg_pld_table4 = 0x2b,
> + .reg_advance = 0xad,
> + },
> + .ngpios = 16,
> + .pins = sx150x_16_pins,
> + .npins = 16, /* oscio not available */
> };
>
> -static const struct of_device_id sx150x_of_match[] = {
> - { .compatible = "semtech,sx1508q" },
> - { .compatible = "semtech,sx1509q" },
> - { .compatible = "semtech,sx1506q" },
> - { .compatible = "semtech,sx1502q" },
> - {},
> +static const struct sx150x_device_data sx1502q_device_data = {
> + .model = SX150X_123,
> + .reg_pullup = 0x02,
> + .reg_pulldn = 0x03,
> + .reg_dir = 0x01,
> + .reg_data = 0x00,
> + .reg_irq_mask = 0x05,
> + .reg_irq_src = 0x08,
> + .reg_sense = 0x07,
> + .pri.x123 = {
> + .reg_pld_mode = 0x10,
> + .reg_pld_table0 = 0x11,
> + .reg_pld_table1 = 0x12,
> + .reg_pld_table2 = 0x13,
> + .reg_pld_table3 = 0x14,
> + .reg_pld_table4 = 0x15,
> + .reg_advance = 0xad,
> + },
> + .ngpios = 8,
> + .pins = sx150x_8_pins,
> + .npins = 8, /* oscio not available */
> };
>
> static s32 sx150x_i2c_write(struct i2c_client *client, u8 reg, u8 val)
> @@ -269,11 +253,6 @@ static s32 sx150x_i2c_read(struct i2c_client *client, u8 reg, u8 *val)
> return err;
> }
>
> -static inline bool offset_is_oscio(struct sx150x_chip *chip, unsigned offset)
> -{
> - return (chip->dev_cfg->ngpios == offset);
> -}
> -
> /*
> * These utility functions solve the common problem of locating and setting
> * configuration bits. Configuration bits are grouped into registers
> @@ -294,7 +273,7 @@ static inline bool offset_is_oscio(struct sx150x_chip *chip, unsigned offset)
> * register and mask the correct bits.
> */
> static inline void sx150x_find_cfg(u8 offset, u8 width,
> - u8 *reg, u8 *mask, u8 *shift)
> + u8 *reg, u8 *mask, u8 *shift)
> {
> *reg -= offset * width / 8;
> *mask = (1 << width) - 1;
> @@ -302,185 +281,241 @@ static inline void sx150x_find_cfg(u8 offset, u8 width,
> *mask <<= *shift;
> }
>
> -static s32 sx150x_write_cfg(struct sx150x_chip *chip,
> - u8 offset, u8 width, u8 reg, u8 val)
> +static int sx150x_write_cfg(struct i2c_client *client,
> + u8 offset, u8 width, u8 reg, u8 val)
> {
> u8 mask;
> u8 data;
> u8 shift;
> - s32 err;
> + int err;
>
> sx150x_find_cfg(offset, width, &reg, &mask, &shift);
> - err = sx150x_i2c_read(chip->client, reg, &data);
> + err = sx150x_i2c_read(client, reg, &data);
> if (err < 0)
> return err;
>
> data &= ~mask;
> data |= (val << shift) & mask;
> - return sx150x_i2c_write(chip->client, reg, data);
> + return sx150x_i2c_write(client, reg, data);
> }
>
> -static int sx150x_get_io(struct sx150x_chip *chip, unsigned offset)
> +static int sx150x_read_cfg(struct i2c_client *client,
> + u8 offset, u8 width, u8 reg)
> {
> - u8 reg = chip->dev_cfg->reg_data;
> u8 mask;
> u8 data;
> u8 shift;
> - s32 err;
> + int err;
>
> - sx150x_find_cfg(offset, 1, &reg, &mask, &shift);
> - err = sx150x_i2c_read(chip->client, reg, &data);
> - if (err >= 0)
> - err = (data & mask) != 0 ? 1 : 0;
> + sx150x_find_cfg(offset, width, &reg, &mask, &shift);
> + err = sx150x_i2c_read(client, reg, &data);
> + if (err < 0)
> + return err;
>
> - return err;
> + return (data & mask);
> }
>
> -static void sx150x_set_oscio(struct sx150x_chip *chip, int val)
> +static int sx150x_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
> {
> - sx150x_i2c_write(chip->client,
> - chip->dev_cfg->pri.x789.reg_clock,
> - (val ? 0x1f : 0x10));
> + return 0;
> }
>
> -static void sx150x_set_io(struct sx150x_chip *chip, unsigned offset, int val)
> +static const char *sx150x_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
> + unsigned int group)
> {
> - sx150x_write_cfg(chip,
> - offset,
> - 1,
> - chip->dev_cfg->reg_data,
> - (val ? 1 : 0));
> + return NULL;
> }
>
> -static int sx150x_io_input(struct sx150x_chip *chip, unsigned offset)
> +static int sx150x_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
> + unsigned int group,
> + const unsigned int **pins,
> + unsigned int *num_pins)
> {
> - return sx150x_write_cfg(chip,
> - offset,
> - 1,
> - chip->dev_cfg->reg_dir,
> - 1);
> + return -ENOTSUPP;
> }
>
> -static int sx150x_io_output(struct sx150x_chip *chip, unsigned offset, int val)
> +static const struct pinctrl_ops sx150x_pinctrl_ops = {
> + .get_groups_count = sx150x_pinctrl_get_groups_count,
> + .get_group_name = sx150x_pinctrl_get_group_name,
> + .get_group_pins = sx150x_pinctrl_get_group_pins,
> +#ifdef CONFIG_OF
> + .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
> + .dt_free_map = pinctrl_utils_free_map,
> +#endif
> +};
> +
> +static bool sx150x_pin_is_oscio(struct sx150x_pinctrl *pctl, unsigned int pin)
> {
> - int err;
> + if (pin >= pctl->data->npins)
> + return false;
>
> - err = sx150x_write_cfg(chip,
> - offset,
> - 1,
> - chip->dev_cfg->reg_data,
> - (val ? 1 : 0));
> - if (err >= 0)
> - err = sx150x_write_cfg(chip,
> - offset,
> - 1,
> - chip->dev_cfg->reg_dir,
> - 0);
> - return err;
> + /* OSCIO pin is only present in 789 devices */
> + if (pctl->data->model != SX150X_789)
> + return false;
> +
> + return !strcmp(pctl->data->pins[pin].name, "oscio");
> }
>
> -static int sx150x_gpio_get(struct gpio_chip *gc, unsigned offset)
> +static int sx150x_gpio_get_direction(struct gpio_chip *chip,
> + unsigned int offset)
> {
> - struct sx150x_chip *chip = gpiochip_get_data(gc);
> - int status = -EINVAL;
> + struct sx150x_pinctrl *pctl = gpiochip_get_data(chip);
> + int status;
>
> - if (!offset_is_oscio(chip, offset)) {
> - mutex_lock(&chip->lock);
> - status = sx150x_get_io(chip, offset);
> - mutex_unlock(&chip->lock);
> - }
> + if (sx150x_pin_is_oscio(pctl, offset))
> + return false;
> +
> + status = sx150x_read_cfg(pctl->client, offset, 1, pctl->data->reg_dir);
> + if (status >= 0)
> + status = !!status;
>
> - return (status < 0) ? status : !!status;
> + return status;
> }
>
> -static void sx150x_gpio_set(struct gpio_chip *gc, unsigned offset, int val)
> +static int sx150x_gpio_get(struct gpio_chip *chip, unsigned int offset)
> {
> - struct sx150x_chip *chip = gpiochip_get_data(gc);
> + struct sx150x_pinctrl *pctl = gpiochip_get_data(chip);
> + int status;
>
> - mutex_lock(&chip->lock);
> - if (offset_is_oscio(chip, offset))
> - sx150x_set_oscio(chip, val);
> - else
> - sx150x_set_io(chip, offset, val);
> - mutex_unlock(&chip->lock);
> + if (sx150x_pin_is_oscio(pctl, offset))
> + return -EINVAL;
> +
> + status = sx150x_read_cfg(pctl->client, offset, 1, pctl->data->reg_data);
> + if (status >= 0)
> + status = !!status;
> +
> + return status;
> }
>
> -static int sx150x_gpio_set_single_ended(struct gpio_chip *gc,
> - unsigned offset,
> - enum single_ended_mode mode)
> +static int sx150x_gpio_set_single_ended(struct gpio_chip *chip,
> + unsigned int offset,
> + enum single_ended_mode mode)
> {
> - struct sx150x_chip *chip = gpiochip_get_data(gc);
> -
> - /* On the SX160X 789 we can set open drain */
> - if (chip->dev_cfg->model != SX150X_789)
> + struct sx150x_pinctrl *pctl = gpiochip_get_data(chip);
> + int ret;
> +
> + switch (mode) {
> + case LINE_MODE_PUSH_PULL:
> + if (pctl->data->model != SX150X_789 ||
> + sx150x_pin_is_oscio(pctl, offset))
> + return 0;
> +
> + mutex_lock(&pctl->lock);
> + ret = sx150x_write_cfg(pctl->client, offset, 1,
> + pctl->data->pri.x789.reg_drain,
> + 0);
> + mutex_unlock(&pctl->lock);
> + if (ret < 0)
> + return ret;
> + break;
> +
> + case LINE_MODE_OPEN_DRAIN:
> + if (pctl->data->model != SX150X_789 ||
> + sx150x_pin_is_oscio(pctl, offset))
> + return -ENOTSUPP;
> +
> + mutex_lock(&pctl->lock);
> + ret = sx150x_write_cfg(pctl->client, offset, 1,
> + pctl->data->pri.x789.reg_drain,
> + 1);
> + mutex_unlock(&pctl->lock);
> + if (ret < 0)
> + return ret;
> + break;
> +
> + default:
> return -ENOTSUPP;
> + }
>
> - if (mode == LINE_MODE_PUSH_PULL)
> - return sx150x_write_cfg(chip,
> - offset,
> - 1,
> - chip->dev_cfg->pri.x789.reg_drain,
> - 0);
> -
> - if (mode == LINE_MODE_OPEN_DRAIN)
> - return sx150x_write_cfg(chip,
> - offset,
> - 1,
> - chip->dev_cfg->pri.x789.reg_drain,
> - 1);
> - return -ENOTSUPP;
> + return 0;
> }
>
> -static int sx150x_gpio_direction_input(struct gpio_chip *gc, unsigned offset)
> +static void sx150x_gpio_set(struct gpio_chip *chip, unsigned int offset,
> + int value)
> {
> - struct sx150x_chip *chip = gpiochip_get_data(gc);
> - int status = -EINVAL;
> + struct sx150x_pinctrl *pctl = gpiochip_get_data(chip);
> +
> + if (sx150x_pin_is_oscio(pctl, offset)) {
>
> - if (!offset_is_oscio(chip, offset)) {
> - mutex_lock(&chip->lock);
> - status = sx150x_io_input(chip, offset);
> - mutex_unlock(&chip->lock);
> + mutex_lock(&pctl->lock);
> + sx150x_i2c_write(pctl->client,
> + pctl->data->pri.x789.reg_clock,
> + (value ? 0x1f : 0x10));
> + mutex_unlock(&pctl->lock);
> + } else {
> + mutex_lock(&pctl->lock);
> + sx150x_write_cfg(pctl->client, offset, 1,
> + pctl->data->reg_data,
> + (value ? 1 : 0));
> + mutex_unlock(&pctl->lock);
> }
> - return status;
> }
>
> -static int sx150x_gpio_direction_output(struct gpio_chip *gc,
> - unsigned offset,
> - int val)
> +static int sx150x_gpio_direction_input(struct gpio_chip *chip,
> + unsigned int offset)
> {
> - struct sx150x_chip *chip = gpiochip_get_data(gc);
> - int status = 0;
> + struct sx150x_pinctrl *pctl = gpiochip_get_data(chip);
> + int ret;
>
> - if (!offset_is_oscio(chip, offset)) {
> - mutex_lock(&chip->lock);
> - status = sx150x_io_output(chip, offset, val);
> - mutex_unlock(&chip->lock);
> + if (sx150x_pin_is_oscio(pctl, offset))
> + return -EINVAL;
> +
> + mutex_lock(&pctl->lock);
> + ret = sx150x_write_cfg(pctl->client, offset, 1,
> + pctl->data->reg_dir, 1);
> + mutex_unlock(&pctl->lock);
> +
> + return ret;
> +}
> +
> +static int sx150x_gpio_direction_output(struct gpio_chip *chip,
> + unsigned int offset, int value)
> +{
> + struct sx150x_pinctrl *pctl = gpiochip_get_data(chip);
> + int status;
> +
> + if (sx150x_pin_is_oscio(pctl, offset)) {
> + sx150x_gpio_set(chip, offset, value);
> + return 0;
> }
> +
> + mutex_lock(&pctl->lock);
> + status = sx150x_write_cfg(pctl->client, offset, 1,
> + pctl->data->reg_data,
> + (value ? 1 : 0));
> + if (status >= 0)
> + status = sx150x_write_cfg(pctl->client, offset, 1,
> + pctl->data->reg_dir, 0);
> + mutex_unlock(&pctl->lock);
> +
> return status;
> }
>
> static void sx150x_irq_mask(struct irq_data *d)
> {
> - struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d));
> - unsigned n = d->hwirq;
> + struct sx150x_pinctrl *pctl =
> + gpiochip_get_data(irq_data_get_irq_chip_data(d));
> + unsigned int n = d->hwirq;
>
> - chip->irq_masked |= (1 << n);
> - chip->irq_update = n;
> + pctl->irq.masked |= (1 << n);
> + pctl->irq.update = n;
> }
>
> static void sx150x_irq_unmask(struct irq_data *d)
> {
> - struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d));
> - unsigned n = d->hwirq;
> + struct sx150x_pinctrl *pctl =
> + gpiochip_get_data(irq_data_get_irq_chip_data(d));
> + unsigned int n = d->hwirq;
>
> - chip->irq_masked &= ~(1 << n);
> - chip->irq_update = n;
> + pctl->irq.masked &= ~(1 << n);
> + pctl->irq.update = n;
> }
>
> static int sx150x_irq_set_type(struct irq_data *d, unsigned int flow_type)
> {
> - struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d));
> - unsigned n, val = 0;
> + struct sx150x_pinctrl *pctl =
> + gpiochip_get_data(irq_data_get_irq_chip_data(d));
> + unsigned int n, val = 0;
>
> if (flow_type & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW))
> return -EINVAL;
> @@ -492,37 +527,40 @@ static int sx150x_irq_set_type(struct irq_data *d, unsigned int flow_type)
> if (flow_type & IRQ_TYPE_EDGE_FALLING)
> val |= 0x2;
>
> - chip->irq_sense &= ~(3UL << (n * 2));
> - chip->irq_sense |= val << (n * 2);
> - chip->irq_update = n;
> + pctl->irq.sense &= ~(3UL << (n * 2));
> + pctl->irq.sense |= val << (n * 2);
> + pctl->irq.update = n;
> return 0;
> }
>
> static irqreturn_t sx150x_irq_thread_fn(int irq, void *dev_id)
> {
> - struct sx150x_chip *chip = (struct sx150x_chip *)dev_id;
> - unsigned nhandled = 0;
> - unsigned sub_irq;
> - unsigned n;
> + struct sx150x_pinctrl *pctl = (struct sx150x_pinctrl *)dev_id;
> + unsigned int nhandled = 0;
> + unsigned int sub_irq;
> + unsigned int n;
> s32 err;
> u8 val;
> int i;
>
> - for (i = (chip->dev_cfg->ngpios / 8) - 1; i >= 0; --i) {
> - err = sx150x_i2c_read(chip->client,
> - chip->dev_cfg->reg_irq_src - i,
> + for (i = (pctl->data->ngpios / 8) - 1; i >= 0; --i) {
> + err = sx150x_i2c_read(pctl->client,
> + pctl->data->reg_irq_src - i,
> &val);
> if (err < 0)
> continue;
>
> - sx150x_i2c_write(chip->client,
> - chip->dev_cfg->reg_irq_src - i,
> - val);
> + err = sx150x_i2c_write(pctl->client,
> + pctl->data->reg_irq_src - i,
> + val);
> + if (err < 0)
> + continue;
> +
> for (n = 0; n < 8; ++n) {
> if (val & (1 << n)) {
> sub_irq = irq_find_mapping(
> - chip->gpio_chip.irqdomain,
> - (i * 8) + n);
> + pctl->gpio.irqdomain,
> + (i * 8) + n);
> handle_nested_irq(sub_irq);
> ++nhandled;
> }
> @@ -534,251 +572,483 @@ static irqreturn_t sx150x_irq_thread_fn(int irq, void *dev_id)
>
> static void sx150x_irq_bus_lock(struct irq_data *d)
> {
> - struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d));
> + struct sx150x_pinctrl *pctl =
> + gpiochip_get_data(irq_data_get_irq_chip_data(d));
>
> - mutex_lock(&chip->lock);
> + mutex_lock(&pctl->lock);
> }
>
> static void sx150x_irq_bus_sync_unlock(struct irq_data *d)
> {
> - struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d));
> - unsigned n;
> + struct sx150x_pinctrl *pctl =
> + gpiochip_get_data(irq_data_get_irq_chip_data(d));
> + unsigned int n;
>
> - if (chip->irq_update == NO_UPDATE_PENDING)
> + if (pctl->irq.update < 0)
> goto out;
>
> - n = chip->irq_update;
> - chip->irq_update = NO_UPDATE_PENDING;
> + n = pctl->irq.update;
> + pctl->irq.update = -1;
>
> /* Avoid updates if nothing changed */
> - if (chip->dev_sense == chip->irq_sense &&
> - chip->dev_masked == chip->irq_masked)
> + if (pctl->irq.dev_sense == pctl->irq.sense &&
> + pctl->irq.dev_masked == pctl->irq.masked)
> goto out;
>
> - chip->dev_sense = chip->irq_sense;
> - chip->dev_masked = chip->irq_masked;
> + pctl->irq.dev_sense = pctl->irq.sense;
> + pctl->irq.dev_masked = pctl->irq.masked;
>
> - if (chip->irq_masked & (1 << n)) {
> - sx150x_write_cfg(chip, n, 1, chip->dev_cfg->reg_irq_mask, 1);
> - sx150x_write_cfg(chip, n, 2, chip->dev_cfg->reg_sense, 0);
> + if (pctl->irq.masked & (1 << n)) {
> + sx150x_write_cfg(pctl->client, n, 1,
> + pctl->data->reg_irq_mask, 1);
> + sx150x_write_cfg(pctl->client, n, 2,
> + pctl->data->reg_sense, 0);
> } else {
> - sx150x_write_cfg(chip, n, 1, chip->dev_cfg->reg_irq_mask, 0);
> - sx150x_write_cfg(chip, n, 2, chip->dev_cfg->reg_sense,
> - chip->irq_sense >> (n * 2));
> + sx150x_write_cfg(pctl->client, n, 1,
> + pctl->data->reg_irq_mask, 0);
> + sx150x_write_cfg(pctl->client, n, 2,
> + pctl->data->reg_sense,
> + pctl->irq.sense >> (n * 2));
> }
> out:
> - mutex_unlock(&chip->lock);
> + mutex_unlock(&pctl->lock);
> }
>
> -static void sx150x_init_chip(struct sx150x_chip *chip,
> - struct i2c_client *client,
> - kernel_ulong_t driver_data,
> - struct sx150x_platform_data *pdata)
> +static int sx150x_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
> + unsigned long *config)
> {
> - mutex_init(&chip->lock);
> -
> - chip->client = client;
> - chip->dev_cfg = &sx150x_devices[driver_data];
> - chip->gpio_chip.parent = &client->dev;
> - chip->gpio_chip.label = client->name;
> - chip->gpio_chip.direction_input = sx150x_gpio_direction_input;
> - chip->gpio_chip.direction_output = sx150x_gpio_direction_output;
> - chip->gpio_chip.get = sx150x_gpio_get;
> - chip->gpio_chip.set = sx150x_gpio_set;
> - chip->gpio_chip.set_single_ended = sx150x_gpio_set_single_ended;
> - chip->gpio_chip.base = pdata->gpio_base;
> - chip->gpio_chip.can_sleep = true;
> - chip->gpio_chip.ngpio = chip->dev_cfg->ngpios;
> -#ifdef CONFIG_OF_GPIO
> - chip->gpio_chip.of_node = client->dev.of_node;
> - chip->gpio_chip.of_gpio_n_cells = 2;
> -#endif
> - if (pdata->oscio_is_gpo)
> - ++chip->gpio_chip.ngpio;
> -
> - chip->irq_chip.name = client->name;
> - chip->irq_chip.irq_mask = sx150x_irq_mask;
> - chip->irq_chip.irq_unmask = sx150x_irq_unmask;
> - chip->irq_chip.irq_set_type = sx150x_irq_set_type;
> - chip->irq_chip.irq_bus_lock = sx150x_irq_bus_lock;
> - chip->irq_chip.irq_bus_sync_unlock = sx150x_irq_bus_sync_unlock;
> - chip->irq_summary = -1;
> - chip->irq_base = -1;
> - chip->irq_masked = ~0;
> - chip->irq_sense = 0;
> - chip->dev_masked = ~0;
> - chip->dev_sense = 0;
> - chip->irq_update = NO_UPDATE_PENDING;
> + struct sx150x_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
> + unsigned int param = pinconf_to_config_param(*config);
> + int ret;
> + u32 arg;
> +
> + if (sx150x_pin_is_oscio(pctl, pin)) {
> + u8 data;
> +
> + switch (param) {
> + case PIN_CONFIG_DRIVE_PUSH_PULL:
> + case PIN_CONFIG_OUTPUT:
> + mutex_lock(&pctl->lock);
> + ret = sx150x_i2c_read(pctl->client,
> + pctl->data->pri.x789.reg_clock,
> + &data);
> + mutex_unlock(&pctl->lock);
> +
> + if (ret < 0)
> + return ret;
> +
> + if (param == PIN_CONFIG_DRIVE_PUSH_PULL)
> + arg = (data & 0x1f) ? 1 : 0;
> + else {
> + if ((data & 0x1f) == 0x1f)
> + arg = 1;
> + else if ((data & 0x1f) == 0x10)
> + arg = 0;
> + else
> + return -EINVAL;
> + }
> +
> + break;
> + default:
> + return -ENOTSUPP;
> + }
> +
> + goto out;
> + }
> +
> + switch (param) {
> + case PIN_CONFIG_BIAS_PULL_DOWN:
> + mutex_lock(&pctl->lock);
> + ret = sx150x_read_cfg(pctl->client, pin, 1,
> + pctl->data->reg_pulldn);
> + mutex_unlock(&pctl->lock);
> +
> + if (ret < 0)
> + return ret;
> +
> + if (!ret)
> + return -EINVAL;
> +
> + arg = 1;
> + break;
> +
> + case PIN_CONFIG_BIAS_PULL_UP:
> + mutex_lock(&pctl->lock);
> + ret = sx150x_read_cfg(pctl->client, pin, 1,
> + pctl->data->reg_pullup);
> + mutex_unlock(&pctl->lock);
> +
> + if (ret < 0)
> + return ret;
> +
> + if (!ret)
> + return -EINVAL;
> +
> + arg = 1;
> + break;
> +
> + case PIN_CONFIG_DRIVE_OPEN_DRAIN:
> + if (pctl->data->model != SX150X_789)
> + return -ENOTSUPP;
> +
> + mutex_lock(&pctl->lock);
> + ret = sx150x_read_cfg(pctl->client, pin, 1,
> + pctl->data->pri.x789.reg_drain);
> + mutex_unlock(&pctl->lock);
> +
> + if (ret < 0)
> + return ret;
> +
> + if (!ret)
> + return -EINVAL;
> +
> + arg = 1;
> + break;
> +
> + case PIN_CONFIG_DRIVE_PUSH_PULL:
> + if (pctl->data->model != SX150X_789)
> + arg = true;
> + else {
> + mutex_lock(&pctl->lock);
> + ret = sx150x_read_cfg(pctl->client, pin, 1,
> + pctl->data->pri.x789.reg_drain);
> + mutex_unlock(&pctl->lock);
> +
> + if (ret < 0)
> + return ret;
> +
> + if (ret)
> + return -EINVAL;
> +
> + arg = 1;
> + }
> + break;
> +
> + case PIN_CONFIG_OUTPUT:
> + ret = sx150x_gpio_get_direction(&pctl->gpio, pin);
> + if (ret < 0)
> + return ret;
> +
> + if (ret)
> + return -EINVAL;
> +
> + ret = sx150x_gpio_get(&pctl->gpio, pin);
> + if (ret < 0)
> + return ret;
> +
> + arg = ret;
> + break;
> +
> + default:
> + return -ENOTSUPP;
> + }
> +
> +out:
> + *config = pinconf_to_config_packed(param, arg);
> +
> + return 0;
> +}
> +
> +static int sx150x_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
> + unsigned long *configs, unsigned int num_configs)
> +{
> + struct sx150x_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
> + enum pin_config_param param;
> + u32 arg;
> + int i;
> + int ret;
> +
> + for (i = 0; i < num_configs; i++) {
> + param = pinconf_to_config_param(configs[i]);
> + arg = pinconf_to_config_argument(configs[i]);
> +
> + if (sx150x_pin_is_oscio(pctl, pin)) {
> + if (param == PIN_CONFIG_OUTPUT) {
> + ret = sx150x_gpio_direction_output(&pctl->gpio,
> + pin, arg);
> + if (ret < 0)
> + return ret;
> +
> + continue;
> + } else
> + return -ENOTSUPP;
> + }
> +
> + switch (param) {
> + case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT:
> + case PIN_CONFIG_BIAS_DISABLE:
> + mutex_lock(&pctl->lock);
> + ret = sx150x_write_cfg(pctl->client, pin, 1,
> + pctl->data->reg_pulldn, 0);
> + mutex_unlock(&pctl->lock);
> + if (ret < 0)
> + return ret;
> +
> + mutex_lock(&pctl->lock);
> + ret = sx150x_write_cfg(pctl->client, pin, 1,
> + pctl->data->reg_pullup, 0);
> + mutex_unlock(&pctl->lock);
> + if (ret < 0)
> + return ret;
> +
> + break;
> +
> + case PIN_CONFIG_BIAS_PULL_UP:
> + mutex_lock(&pctl->lock);
> + ret = sx150x_write_cfg(pctl->client, pin, 1,
> + pctl->data->reg_pullup,
> + 1);
> + mutex_unlock(&pctl->lock);
> + if (ret < 0)
> + return ret;
> +
> + break;
> +
> + case PIN_CONFIG_BIAS_PULL_DOWN:
> + mutex_lock(&pctl->lock);
> + ret = sx150x_write_cfg(pctl->client, pin, 1,
> + pctl->data->reg_pulldn,
> + 1);
> + mutex_unlock(&pctl->lock);
> + if (ret < 0)
> + return ret;
> +
> + break;
> +
> + case PIN_CONFIG_DRIVE_OPEN_DRAIN:
> + ret = sx150x_gpio_set_single_ended(&pctl->gpio,
> + pin, LINE_MODE_OPEN_DRAIN);
> + if (ret < 0)
> + return ret;
> +
> + break;
> +
> + case PIN_CONFIG_DRIVE_PUSH_PULL:
> + ret = sx150x_gpio_set_single_ended(&pctl->gpio,
> + pin, LINE_MODE_PUSH_PULL);
> + if (ret < 0)
> + return ret;
> +
> + break;
> +
> + case PIN_CONFIG_OUTPUT:
> + ret = sx150x_gpio_direction_output(&pctl->gpio,
> + pin, arg);
> + if (ret < 0)
> + return ret;
> +
> + break;
> +
> + default:
> + return -ENOTSUPP;
> + }
> + } /* for each config */
> +
> + return 0;
> }
>
> -static int sx150x_init_io(struct sx150x_chip *chip, u8 base, u16 cfg)
> +static const struct pinconf_ops sx150x_pinconf_ops = {
> + .pin_config_get = sx150x_pinconf_get,
> + .pin_config_set = sx150x_pinconf_set,
> + .is_generic = true,
> +};
> +
> +static const struct i2c_device_id sx150x_id[] = {
> + {"sx1508q", (kernel_ulong_t) &sx1508q_device_data },
> + {"sx1509q", (kernel_ulong_t) &sx1509q_device_data },
> + {"sx1506q", (kernel_ulong_t) &sx1506q_device_data },
> + {"sx1502q", (kernel_ulong_t) &sx1502q_device_data },
> + {}
> +};
> +
> +static const struct of_device_id sx150x_of_match[] = {
> + { .compatible = "semtech,sx1508q" },
> + { .compatible = "semtech,sx1509q" },
> + { .compatible = "semtech,sx1506q" },
> + { .compatible = "semtech,sx1502q" },
> + {},
> +};
> +
> +static int sx150x_init_io(struct sx150x_pinctrl *pctl, u8 base, u16 cfg)
> {
> int err = 0;
> - unsigned n;
> + unsigned int n;
>
> - for (n = 0; err >= 0 && n < (chip->dev_cfg->ngpios / 8); ++n)
> - err = sx150x_i2c_write(chip->client, base - n, cfg >> (n * 8));
> + for (n = 0; err >= 0 && n < (pctl->data->ngpios / 8); ++n)
> + err = sx150x_i2c_write(pctl->client, base - n, cfg >> (n * 8));
> return err;
> }
>
> -static int sx150x_reset(struct sx150x_chip *chip)
> +static int sx150x_reset(struct sx150x_pinctrl *pctl)
> {
> int err;
>
> - err = i2c_smbus_write_byte_data(chip->client,
> - chip->dev_cfg->pri.x789.reg_reset,
> + err = i2c_smbus_write_byte_data(pctl->client,
> + pctl->data->pri.x789.reg_reset,
> 0x12);
> if (err < 0)
> return err;
>
> - err = i2c_smbus_write_byte_data(chip->client,
> - chip->dev_cfg->pri.x789.reg_reset,
> + err = i2c_smbus_write_byte_data(pctl->client,
> + pctl->data->pri.x789.reg_reset,
> 0x34);
> return err;
> }
>
> -static int sx150x_init_hw(struct sx150x_chip *chip,
> - struct sx150x_platform_data *pdata)
> +static int sx150x_init_hw(struct sx150x_pinctrl *pctl)
> {
> - int err = 0;
> + int err;
>
> - if (pdata->reset_during_probe) {
> - err = sx150x_reset(chip);
> + if (pctl->data->model == SX150X_789 &&
> + of_property_read_bool(pctl->dev->of_node, "semtech,probe-reset")) {
> + err = sx150x_reset(pctl);
> if (err < 0)
> return err;
> }
>
> - if (chip->dev_cfg->model == SX150X_789)
> - err = sx150x_i2c_write(chip->client,
> - chip->dev_cfg->pri.x789.reg_misc,
> + if (pctl->data->model == SX150X_789)
> + err = sx150x_i2c_write(pctl->client,
> + pctl->data->pri.x789.reg_misc,
> 0x01);
> - else if (chip->dev_cfg->model == SX150X_456)
> - err = sx150x_i2c_write(chip->client,
> - chip->dev_cfg->pri.x456.reg_advance,
> + else if (pctl->data->model == SX150X_456)
> + err = sx150x_i2c_write(pctl->client,
> + pctl->data->pri.x456.reg_advance,
> 0x04);
> else
> - err = sx150x_i2c_write(chip->client,
> - chip->dev_cfg->pri.x123.reg_advance,
> + err = sx150x_i2c_write(pctl->client,
> + pctl->data->pri.x123.reg_advance,
> 0x00);
> if (err < 0)
> return err;
>
> - err = sx150x_init_io(chip, chip->dev_cfg->reg_pullup,
> - pdata->io_pullup_ena);
> - if (err < 0)
> - return err;
> -
> - err = sx150x_init_io(chip, chip->dev_cfg->reg_pulldn,
> - pdata->io_pulldn_ena);
> - if (err < 0)
> - return err;
> -
> - if (chip->dev_cfg->model == SX150X_789) {
> - err = sx150x_init_io(chip,
> - chip->dev_cfg->pri.x789.reg_polarity,
> - pdata->io_polarity);
> + /* Set all pins to work in normal mode */
> + if (pctl->data->model == SX150X_789) {
> + err = sx150x_init_io(pctl,
> + pctl->data->pri.x789.reg_polarity,
> + 0);
> if (err < 0)
> return err;
> - } else if (chip->dev_cfg->model == SX150X_456) {
> + } else if (pctl->data->model == SX150X_456) {
> /* Set all pins to work in normal mode */
> - err = sx150x_init_io(chip,
> - chip->dev_cfg->pri.x456.reg_pld_mode,
> + err = sx150x_init_io(pctl,
> + pctl->data->pri.x456.reg_pld_mode,
> 0);
> if (err < 0)
> return err;
> } else {
> /* Set all pins to work in normal mode */
> - err = sx150x_init_io(chip,
> - chip->dev_cfg->pri.x123.reg_pld_mode,
> + err = sx150x_init_io(pctl,
> + pctl->data->pri.x123.reg_pld_mode,
> 0);
> if (err < 0)
> return err;
> }
>
> -
> - if (pdata->oscio_is_gpo)
> - sx150x_set_oscio(chip, 0);
> -
> - return err;
> -}
> -
> -static int sx150x_install_irq_chip(struct sx150x_chip *chip,
> - int irq_summary,
> - int irq_base)
> -{
> - int err;
> -
> - chip->irq_summary = irq_summary;
> - chip->irq_base = irq_base;
> -
> - /* Add gpio chip to irq subsystem */
> - err = gpiochip_irqchip_add(&chip->gpio_chip,
> - &chip->irq_chip, chip->irq_base,
> - handle_edge_irq, IRQ_TYPE_EDGE_BOTH);
> - if (err) {
> - dev_err(&chip->client->dev,
> - "could not connect irqchip to gpiochip\n");
> - return err;
> - }
> -
> - err = devm_request_threaded_irq(&chip->client->dev,
> - irq_summary, NULL, sx150x_irq_thread_fn,
> - IRQF_ONESHOT | IRQF_SHARED | IRQF_TRIGGER_FALLING,
> - chip->irq_chip.name, chip);
> - if (err < 0) {
> - chip->irq_summary = -1;
> - chip->irq_base = -1;
> - }
> -
> - return err;
> + return 0;
> }
>
> static int sx150x_probe(struct i2c_client *client,
> - const struct i2c_device_id *id)
> + const struct i2c_device_id *id)
> {
> static const u32 i2c_funcs = I2C_FUNC_SMBUS_BYTE_DATA |
> I2C_FUNC_SMBUS_WRITE_WORD_DATA;
> - struct sx150x_platform_data *pdata;
> - struct sx150x_chip *chip;
> - int rc;
> + struct device *dev = &client->dev;
> + struct sx150x_pinctrl *pctl;
> + int ret;
>
> - pdata = dev_get_platdata(&client->dev);
> - if (!pdata)
> + if (!id->driver_data)
> return -EINVAL;
>
> if (!i2c_check_functionality(client->adapter, i2c_funcs))
> return -ENOSYS;
>
> - chip = devm_kzalloc(&client->dev,
> - sizeof(struct sx150x_chip), GFP_KERNEL);
> - if (!chip)
> + pctl = devm_kzalloc(dev, sizeof(*pctl), GFP_KERNEL);
> + if (!pctl)
> return -ENOMEM;
>
> - sx150x_init_chip(chip, client, id->driver_data, pdata);
> - rc = sx150x_init_hw(chip, pdata);
> - if (rc < 0)
> - return rc;
> -
> - rc = devm_gpiochip_add_data(&client->dev, &chip->gpio_chip, chip);
> - if (rc)
> - return rc;
> -
> - if (pdata->irq_summary >= 0) {
> - rc = sx150x_install_irq_chip(chip,
> - pdata->irq_summary,
> - pdata->irq_base);
> - if (rc < 0)
> - return rc;
> + pctl->dev = dev;
> + pctl->client = client;
> + pctl->data = (void *)id->driver_data;
> +
> + mutex_init(&pctl->lock);
> +
> + ret = sx150x_init_hw(pctl);
> + if (ret)
> + return ret;
> +
> + /* Register GPIO controller */
> + pctl->gpio.label = devm_kstrdup(dev, client->name, GFP_KERNEL);
> + pctl->gpio.base = -1;
> + pctl->gpio.ngpio = pctl->data->npins;
> + pctl->gpio.get_direction = sx150x_gpio_get_direction;
> + pctl->gpio.direction_input = sx150x_gpio_direction_input;
> + pctl->gpio.direction_output = sx150x_gpio_direction_output;
> + pctl->gpio.get = sx150x_gpio_get;
> + pctl->gpio.set = sx150x_gpio_set;
> + pctl->gpio.set_single_ended = sx150x_gpio_set_single_ended;
> + pctl->gpio.parent = dev;
> +#ifdef CONFIG_OF_GPIO
> + pctl->gpio.of_node = dev->of_node;
> +#endif
> + pctl->gpio.can_sleep = true;
> +
> + ret = devm_gpiochip_add_data(dev, &pctl->gpio, pctl);
> + if (ret)
> + return ret;
> +
> + /* Add Interrupt support if an irq is specified */
> + if (client->irq > 0) {
> + pctl->irq_chip.name = devm_kstrdup(dev, client->name,
> + GFP_KERNEL);
> + pctl->irq_chip.irq_mask = sx150x_irq_mask;
> + pctl->irq_chip.irq_unmask = sx150x_irq_unmask;
> + pctl->irq_chip.irq_set_type = sx150x_irq_set_type;
> + pctl->irq_chip.irq_bus_lock = sx150x_irq_bus_lock;
> + pctl->irq_chip.irq_bus_sync_unlock = sx150x_irq_bus_sync_unlock;
> +
> + pctl->irq.masked = ~0;
> + pctl->irq.sense = 0;
> + pctl->irq.dev_masked = ~0;
> + pctl->irq.dev_sense = 0;
> + pctl->irq.update = -1;
> +
> + ret = gpiochip_irqchip_add(&pctl->gpio,
> + &pctl->irq_chip, 0,
> + handle_edge_irq, IRQ_TYPE_EDGE_BOTH);
> + if (ret) {
> + dev_err(dev, "could not connect irqchip to gpiochip\n");
> + return ret;
> + }
> +
> + ret = devm_request_threaded_irq(dev, client->irq, NULL,
> + sx150x_irq_thread_fn,
> + IRQF_ONESHOT | IRQF_SHARED |
> + IRQF_TRIGGER_FALLING,
> + pctl->irq_chip.name, pctl);
> + if (ret < 0)
> + return ret;
> }
>
> - i2c_set_clientdata(client, chip);
> + /* Pinctrl_desc */
> + pctl->pinctrl_desc.name = "sx150x-pinctrl";
> + pctl->pinctrl_desc.pctlops = &sx150x_pinctrl_ops;
> + pctl->pinctrl_desc.confops = &sx150x_pinconf_ops;
> + pctl->pinctrl_desc.pins = pctl->data->pins;
> + pctl->pinctrl_desc.npins = pctl->data->npins;
> + pctl->pinctrl_desc.owner = THIS_MODULE;
> +
> + pctl->pctldev = pinctrl_register(&pctl->pinctrl_desc, dev, pctl);
> + if (IS_ERR(pctl->pctldev)) {
> + dev_err(dev, "Failed to register pinctrl device\n");
> + return PTR_ERR(pctl->pctldev);
> + }
>
> return 0;
> }
>
> static struct i2c_driver sx150x_driver = {
> .driver = {
> - .name = "sx150x",
> + .name = "sx150x-pinctrl",
> .of_match_table = of_match_ptr(sx150x_of_match),
> },
> .probe = sx150x_probe,
>