Re: [PATCH 05/12] ARM: dts: imx6ul-isiot-common: Add touchscreen node

From: Jagan Teki
Date: Fri Mar 24 2017 - 03:33:02 EST


On Fri, Mar 24, 2017 at 12:55 PM, Shawn Guo <shawnguo@xxxxxxxxxx> wrote:
> On Fri, Mar 24, 2017 at 12:29:49PM +0530, Jagan Teki wrote:
>> On Fri, Mar 24, 2017 at 10:46 AM, Shawn Guo <shawnguo@xxxxxxxxxx> wrote:
>> > On Wed, Mar 22, 2017 at 11:18:10PM +0530, Jagan Teki wrote:
>> >> From: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx>
>> >>
>> >> Add touchscreen node as i2c1 slave device on Engicam Is.IoT MX6UL
>> >> modules, the touchscreen controlled 'st,stmpe-ts' connected via
>> >> i2c with st,stmpe811 mfb interface.
>> >
>> > s/mfb/mfd?
>> >
>> >>
>> >> Cc: Shawn Guo <shawnguo@xxxxxxxxxx>
>> >> Cc: Matteo Lisi <matteo.lisi@xxxxxxxxxxx>
>> >> Cc: Michael Trimarchi <michael@xxxxxxxxxxxxxxxxxxxx>
>> >> Signed-off-by: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx>
>> >> ---
>> >> arch/arm/boot/dts/imx6ul-isiot-common.dtsi | 34 ++++++++++++++++++++++++++++++
>> >> 1 file changed, 34 insertions(+)
>> >>
>> >> diff --git a/arch/arm/boot/dts/imx6ul-isiot-common.dtsi b/arch/arm/boot/dts/imx6ul-isiot-common.dtsi
>> >> index 9660e20..b149b5e 100644
>> >> --- a/arch/arm/boot/dts/imx6ul-isiot-common.dtsi
>> >> +++ b/arch/arm/boot/dts/imx6ul-isiot-common.dtsi
>> >> @@ -40,6 +40,34 @@
>> >> * OTHER DEALINGS IN THE SOFTWARE.
>> >> */
>> >>
>> >> +&i2c1 {
>> >> + touch: stmpe811@44 {
>> >
>> > Label a MFD device 'touch'? Also, the node name should be generic. Not
>> > sure what should be used for MFD device though.
>>
>> May be I can use stmpe811@41 the existing imx6qdl-apalis.dtsi using
>> the similar notation.
>
> Per application notes of stmpe811 below, I would suggest you name it
> gpio-expander.
>
> www.st.com/resource/zh/datasheet/CD00186725.pdf

OK, will this be ok?

stmpe811: gpio-expander@44 {

>
>>
>> >
>> >> + compatible = "st,stmpe811";
>> >> + reg = <0x44>;
>> >> + #address-cells = <1>;
>> >> + #size-cells = <0>;
>> >> + pinctrl-names = "default";
>> >> + pinctrl-0 = <&pinctrl_stmpe_ts>;
>> >
>> > If this is for stmpe-ts, shouldn't be put into touchscreen child node?
>>
>> Actually this is interrupt pad, for the touch controller via stmpe so
>> I can rename pinctrl_touch_int.
>
> Or just pinctrl_stmpe.
>
>>
>> >
>> >> + interrupt-parent = <&gpio1>;
>> >> + interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
>> >> + interrupt-controller;
>> >> + #interrupt-cells = <2>;
>> >> +
>> >> + stmpe_touchscreen {
>> >
>> > 'stmpe: touchscreen {' might be better.
>>
>> stmpe_touchscreen {
>>
>> This is also compatible with existing dtsi files
>
> We do not need to keep compatibility with something not good.

thanks!
--
Jagan Teki
Senior Linux Kernel Engineer | Amarula Solutions
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.