Re: [PATCH v2 3/3] hwmon: ltc2990: support all measurement modes
From: Tom Levens
Date: Wed Jun 28 2017 - 11:31:03 EST
On Wed, 28 Jun 2017, Guenter Roeck wrote:
On Wed, Jun 28, 2017 at 04:24:03PM +0200, Mike Looijmans wrote:
ïOn 17-11-16 17:56, Guenter Roeck wrote:
On 11/17/2016 04:10 AM, Tom Levens wrote:
Updated version of the ltc2990 driver which supports all measurement
modes available in the chip. The mode can be set through a devicetree
attribute.
property
Signed-off-by: Tom Levens <tom.levens@xxxxxxx>
---
Changes since v1:
* Refactored value conversion (patch 1/3)
* Split the devicetree binding into separate patch (patch 2/3)
* Specifying an invalid mode now returns -EINVAL, previously this
only issued a warning and used the default value
* Removed the "mode" sysfs attribute, as the mode of the chip is
hardware specific and should not be user configurable. This allows much
simpler code as a result.
Documentation/hwmon/ltc2990 | 24 ++++---
drivers/hwmon/Kconfig | 7 +--
drivers/hwmon/ltc2990.c | 167 ++++++++++++++++++++++++++++++++++++-------
3 files changed, 159 insertions(+), 39 deletions(-)
diff --git a/Documentation/hwmon/ltc2990 b/Documentation/hwmon/ltc2990
index c25211e..3ed68f6 100644
--- a/Documentation/hwmon/ltc2990
+++ b/Documentation/hwmon/ltc2990
@@ -8,6 +8,7 @@ Supported chips:
Datasheet: http://www.linear.com/product/ltc2990
Author: Mike Looijmans <mike.looijmans@xxxxxxxx>
+ Tom Levens <tom.levens@xxxxxxx>
Description
@@ -16,10 +17,8 @@ Description
LTC2990 is a Quad I2C Voltage, Current and Temperature Monitor.
The chip's inputs can measure 4 voltages, or two inputs together (1+2 and 3+4)
can be combined to measure a differential voltage, which is typically used to
-measure current through a series resistor, or a temperature.
-
-This driver currently uses the 2x differential mode only. In order to support
-other modes, the driver will need to be expanded.
+measure current through a series resistor, or a temperature with an external
+diode.
Usage Notes
@@ -32,12 +31,19 @@ devices explicitly.
Sysfs attributes
----------------
+in0_input Voltage at Vcc pin in millivolt (range 2.5V to 5V)
+temp1_input Internal chip temperature in millidegrees Celcius
+
+A subset of the following attributes are visible, depending on the measurement
+mode of the chip.
+
+in[1-4]_input Voltage at V[1-4] pin in millivolt
+temp2_input External temperature sensor TR1 in millidegrees Celcius
+temp3_input External temperature sensor TR2 in millidegrees Celcius
+curr1_input Current in mA across V1-V2 assuming a 1mOhm sense resistor
+curr2_input Current in mA across V3-V4 assuming a 1mOhm sense resistor
+
The "curr*_input" measurements actually report the voltage drop across the
input pins in microvolts. This is equivalent to the current through a 1mOhm
sense resistor. Divide the reported value by the actual sense resistor value
in mOhm to get the actual value.
-
-in0_input Voltage at Vcc pin in millivolt (range 2.5V to 5V)
-temp1_input Internal chip temperature in millidegrees Celcius
-curr1_input Current in mA across v1-v2 assuming a 1mOhm sense resistor.
-curr2_input Current in mA across v3-v4 assuming a 1mOhm sense resistor.
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 45cef3d..f7096ca 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -699,15 +699,12 @@ config SENSORS_LTC2945
be called ltc2945.
config SENSORS_LTC2990
- tristate "Linear Technology LTC2990 (current monitoring mode only)"
+ tristate "Linear Technology LTC2990"
depends on I2C
help
If you say yes here you get support for Linear Technology LTC2990
I2C System Monitor. The LTC2990 supports a combination of voltage,
- current and temperature monitoring, but in addition to the Vcc supply
- voltage and chip temperature, this driver currently only supports
- reading two currents by measuring two differential voltages across
- series resistors.
+ current and temperature monitoring.
This driver can also be built as a module. If so, the module will
be called ltc2990.
diff --git a/drivers/hwmon/ltc2990.c b/drivers/hwmon/ltc2990.c
index 0ec4102..e8d36f5 100644
--- a/drivers/hwmon/ltc2990.c
+++ b/drivers/hwmon/ltc2990.c
@@ -6,11 +6,7 @@
*
* License: GPLv2
*
- * This driver assumes the chip is wired as a dual current monitor, and
- * reports the voltage drop across two series resistors. It also reports
- * the chip's internal temperature and Vcc power supply voltage.
- *
- * Value conversion refactored
+ * Value conversion refactored and support for all measurement modes added
* by Tom Levens <tom.levens@xxxxxxx>
*/
@@ -21,6 +17,7 @@
#include <linux/i2c.h>
#include <linux/kernel.h>
#include <linux/module.h>
+#include <linux/of.h>
#define LTC2990_STATUS 0x00
#define LTC2990_CONTROL 0x01
@@ -35,32 +32,96 @@
#define LTC2990_CONTROL_KELVIN BIT(7)
#define LTC2990_CONTROL_SINGLE BIT(6)
#define LTC2990_CONTROL_MEASURE_ALL (0x3 << 3)
-#define LTC2990_CONTROL_MODE_CURRENT 0x06
-#define LTC2990_CONTROL_MODE_VOLTAGE 0x07
+#define LTC2990_CONTROL_MODE_DEFAULT 0x06
I think LTC2990_CONTROL_MODE_CURRENT was better - it describes the actual mode.
Changing the define to _DEFAULT does not really improve code readability.
+#define LTC2990_CONTROL_MODE_MAX 0x07
+
+#define LTC2990_IN0 BIT(0)
+#define LTC2990_IN1 BIT(1)
+#define LTC2990_IN2 BIT(2)
+#define LTC2990_IN3 BIT(3)
+#define LTC2990_IN4 BIT(4)
+#define LTC2990_CURR1 BIT(5)
+#define LTC2990_CURR2 BIT(6)
+#define LTC2990_TEMP1 BIT(7)
+#define LTC2990_TEMP2 BIT(8)
+#define LTC2990_TEMP3 BIT(9)
+
+static const int ltc2990_attrs_ena[] = {
+ LTC2990_IN1 | LTC2990_IN2 | LTC2990_TEMP3,
+ LTC2990_CURR1 | LTC2990_TEMP3,
+ LTC2990_CURR1 | LTC2990_IN3 | LTC2990_IN4,
+ LTC2990_TEMP2 | LTC2990_IN3 | LTC2990_IN4,
+ LTC2990_TEMP2 | LTC2990_CURR2,
+ LTC2990_TEMP2 | LTC2990_TEMP3,
+ LTC2990_CURR1 | LTC2990_CURR2,
+ LTC2990_IN1 | LTC2990_IN2 | LTC2990_IN3 | LTC2990_IN4
+};
+
+struct ltc2990_data {
+ struct i2c_client *i2c;
+ u32 mode;
+};
/* Return the converted value from the given register in uV or mC */
-static int ltc2990_get_value(struct i2c_client *i2c, u8 reg, s32 *result)
+static int ltc2990_get_value(struct i2c_client *i2c, int index, s32 *result)
{
s32 val;
+ u8 reg;
+
+ switch (index) {
+ case LTC2990_IN0:
+ reg = LTC2990_VCC_MSB;
+ break;
+ case LTC2990_IN1:
+ case LTC2990_CURR1:
+ case LTC2990_TEMP2:
+ reg = LTC2990_V1_MSB;
+ break;
+ case LTC2990_IN2:
+ reg = LTC2990_V2_MSB;
+ break;
+ case LTC2990_IN3:
+ case LTC2990_CURR2:
+ case LTC2990_TEMP3:
+ reg = LTC2990_V3_MSB;
+ break;
+ case LTC2990_IN4:
+ reg = LTC2990_V4_MSB;
+ break;
+ case LTC2990_TEMP1:
+ reg = LTC2990_TINT_MSB;
+ break;
+ default:
+ return -EINVAL;
+ }
val = i2c_smbus_read_word_swapped(i2c, reg);
if (unlikely(val < 0))
return val;
- switch (reg) {
- case LTC2990_TINT_MSB:
- /* internal temp, 0.0625 degrees/LSB, 13-bit */
+ switch (index) {
+ case LTC2990_TEMP1:
+ case LTC2990_TEMP2:
+ case LTC2990_TEMP3:
+ /* temp, 0.0625 degrees/LSB, 13-bit */
*result = sign_extend32(val, 12) * 1000 / 16;
break;
- case LTC2990_V1_MSB:
- case LTC2990_V3_MSB:
- /* Vx-Vy, 19.42uV/LSB. Depends on mode. */
+ case LTC2990_CURR1:
+ case LTC2990_CURR2:
+ /* Vx-Vy, 19.42uV/LSB */
*result = sign_extend32(val, 14) * 1942 / 100;
break;
- case LTC2990_VCC_MSB:
- /* Vcc, 305.18ÃÂV/LSB, 2.5V offset */
+ case LTC2990_IN0:
+ /* Vcc, 305.18uV/LSB, 2.5V offset */
*result = sign_extend32(val, 14) * 30518 / (100 * 1000) + 2500;
break;
+ case LTC2990_IN1:
+ case LTC2990_IN2:
+ case LTC2990_IN3:
+ case LTC2990_IN4:
+ /* Vx: 305.18uV/LSB */
+ *result = sign_extend32(val, 14) * 30518 / (100 * 1000);
+ break;
default:
return -EINVAL; /* won't happen, keep compiler happy */
}
@@ -72,48 +133,104 @@ static ssize_t ltc2990_show_value(struct device *dev,
struct device_attribute *da, char *buf)
{
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+ struct ltc2990_data *data = dev_get_drvdata(dev);
s32 value;
int ret;
- ret = ltc2990_get_value(dev_get_drvdata(dev), attr->index, &value);
+ ret = ltc2990_get_value(data->i2c, attr->index, &value);
if (unlikely(ret < 0))
return ret;
return snprintf(buf, PAGE_SIZE, "%d\n", value);
}
+static umode_t ltc2990_attrs_visible(struct kobject *kobj,
+ struct attribute *a, int n)
+{
+ struct device *dev = container_of(kobj, struct device, kobj);
+ struct ltc2990_data *data = dev_get_drvdata(dev);
+ struct device_attribute *da =
+ container_of(a, struct device_attribute, attr);
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+
+ if (attr->index == LTC2990_TEMP1 ||
+ attr->index == LTC2990_IN0 ||
+ attr->index & ltc2990_attrs_ena[data->mode])
+ return a->mode;
+ else
Unnecessary else
+ return 0;
+}
+
static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, ltc2990_show_value, NULL,
- LTC2990_TINT_MSB);
+ LTC2990_TEMP1);
+static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, ltc2990_show_value, NULL,
+ LTC2990_TEMP2);
+static SENSOR_DEVICE_ATTR(temp3_input, S_IRUGO, ltc2990_show_value, NULL,
+ LTC2990_TEMP3);
static SENSOR_DEVICE_ATTR(curr1_input, S_IRUGO, ltc2990_show_value, NULL,
- LTC2990_V1_MSB);
+ LTC2990_CURR1);
static SENSOR_DEVICE_ATTR(curr2_input, S_IRUGO, ltc2990_show_value, NULL,
- LTC2990_V3_MSB);
+ LTC2990_CURR2);
static SENSOR_DEVICE_ATTR(in0_input, S_IRUGO, ltc2990_show_value, NULL,
- LTC2990_VCC_MSB);
+ LTC2990_IN0);
+static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, ltc2990_show_value, NULL,
+ LTC2990_IN1);
+static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, ltc2990_show_value, NULL,
+ LTC2990_IN2);
+static SENSOR_DEVICE_ATTR(in3_input, S_IRUGO, ltc2990_show_value, NULL,
+ LTC2990_IN3);
+static SENSOR_DEVICE_ATTR(in4_input, S_IRUGO, ltc2990_show_value, NULL,
+ LTC2990_IN4);
static struct attribute *ltc2990_attrs[] = {
&sensor_dev_attr_temp1_input.dev_attr.attr,
+ &sensor_dev_attr_temp2_input.dev_attr.attr,
+ &sensor_dev_attr_temp3_input.dev_attr.attr,
&sensor_dev_attr_curr1_input.dev_attr.attr,
&sensor_dev_attr_curr2_input.dev_attr.attr,
&sensor_dev_attr_in0_input.dev_attr.attr,
+ &sensor_dev_attr_in1_input.dev_attr.attr,
+ &sensor_dev_attr_in2_input.dev_attr.attr,
+ &sensor_dev_attr_in3_input.dev_attr.attr,
+ &sensor_dev_attr_in4_input.dev_attr.attr,
NULL,
};
-ATTRIBUTE_GROUPS(ltc2990);
+
+static const struct attribute_group ltc2990_group = {
+ .attrs = ltc2990_attrs,
+ .is_visible = ltc2990_attrs_visible,
+};
+__ATTRIBUTE_GROUPS(ltc2990);
static int ltc2990_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)
{
int ret;
struct device *hwmon_dev;
+ struct ltc2990_data *data;
+ struct device_node *of_node = i2c->dev.of_node;
if (!i2c_check_functionality(i2c->adapter, I2C_FUNC_SMBUS_BYTE_DATA |
I2C_FUNC_SMBUS_WORD_DATA))
return -ENODEV;
- /* Setup continuous mode, current monitor */
+ data = devm_kzalloc(&i2c->dev, sizeof(struct ltc2990_data), GFP_KERNEL);
+ if (unlikely(!data))
+ return -ENOMEM;
+ data->i2c = i2c;
+
+ if (!of_node || of_property_read_u32(of_node, "lltc,mode", &data->mode))
+ data->mode = LTC2990_CONTROL_MODE_DEFAULT;
Iam arguing with myself if we should still do this or if we should read the mode
from the chip instead if it isn't provided (after all, it may have been
initialized
by the BIOS/ROMMON).
Mike, would that break your application, or can you specify the mode in
devicetree ?
OMFG, I just spent half the day implementing the exact same thing, and only
after sumbmitting it, I stumbled upon this thread. I must be getting old.
A well, seems I implemented things a bit differently, so you get to pick and
choose which patch was better.
As I just replied to your patch, there is no question here. The compatible
statement refers to chip compatibility; one can not use it to also provide
configuration information.
Whatever happened to this patch though? It didn't make it to mainline,
otherwise I'd have found it sooner...
I'll have to look it up, but I guess I didn't get an updated version.
As far as I remember I had a working V3 of this patch, but it is entirely
possible that it was never submitted as I have been busy with other
projects recently. I'll dig it out and check that it is complete.
Cheers,
Guenter
Thanks,
Guenter
+
+ if (data->mode > LTC2990_CONTROL_MODE_MAX) {
+ dev_err(&i2c->dev, "Error: Invalid mode %d.\n", data->mode);
+ return -EINVAL;
+ }
+
+ /* Setup continuous mode */
ret = i2c_smbus_write_byte_data(i2c, LTC2990_CONTROL,
LTC2990_CONTROL_MEASURE_ALL |
- LTC2990_CONTROL_MODE_CURRENT);
+ data->mode);
if (ret < 0) {
dev_err(&i2c->dev, "Error: Failed to set control mode.\n");
return ret;
@@ -127,7 +244,7 @@ static int ltc2990_i2c_probe(struct i2c_client *i2c,
hwmon_dev = devm_hwmon_device_register_with_groups(&i2c->dev,
i2c->name,
- i2c,
+ data,
ltc2990_groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
Kind regards,
Mike Looijmans
System Expert
TOPIC Products
Materiaalweg 4, NL-5681 RJ Best
Postbus 440, NL-5680 AK Best
Telefoon: +31 (0) 499 33 69 79
E-mail: mike.looijmans@xxxxxxxxxxxxxxxxx
Website: www.topicproducts.com
Please consider the environment before printing this e-mail