Re: [PATCHv3 1/3] dt-bindings: display: Intel FPGA VIP drm driver Devicetree bindings
From: Rob Herring
Date: Mon Jul 17 2017 - 13:44:58 EST
On Thu, Jul 13, 2017 at 09:40:45AM +0800, hean.loong.ong@xxxxxxxxx wrote:
> From: "Ong, Hean Loong" <hean.loong.ong@xxxxxxxxx>
>
> Device tree binding for Intel FPGA Video and Image
> Processing Suite. The binding involved would be generated
> from the Altera (Intel) Qsys system. The bindings would
> set the max width, max height, buts per pixel and memory
> port width. The device tree binding only supports the Intel
> Arria10 devkit and its variants. Vendor name retained as
> altr.
>
> Signed-off-by: Ong, Hean Loong <hean.loong.ong@xxxxxxxxx>
> ---
> .../devicetree/bindings/display/altr,vip-fb2.txt | 41 ++++++++++++++++++++++
> 1 file changed, 41 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/altr,vip-fb2.txt
>
> diff --git a/Documentation/devicetree/bindings/display/altr,vip-fb2.txt b/Documentation/devicetree/bindings/display/altr,vip-fb2.txt
> new file mode 100644
> index 0000000..ce249fd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/altr,vip-fb2.txt
> @@ -0,0 +1,41 @@
> +Intel Video and Image Processing(VIP) Frame Buffer II bindings
> +
> +Supported hardware: Arria 10 and above with display port IP
> +
> +The hardware associated with this device tree is a SoC FPGA. Where there is an ARM controller
> +and a FPGA device. The ARM controller would host the Linux OS while the FPGA device runs on its
> +individual IP firmware. In the Intel VIP Frame Buffer II the ARM controller would be
> +driving data from the Linux OS to the FPGA device programmed with the Frame Buffer II IP
> +to render pixels to be streamed to the Display Port connector.
> +
> +The DRM driver for the Arria 10 devkit would require the display resolution
Bindings are for h/w, not drivers and DRM is a Linuxism.
> +and pixel information to be included as these values are generated based
> +on the FPGA design that drives the video connector attached to the DRM driver.
> +
> +The Frame Buffer II device is a simple frame buffer device. The device contains the display
> +properties and the bridge or connector register. The output for this device currently
> +is a dedicated to a single Display Port.
> +
> +More information the FPGA video IP component can be acquired from
> +https://www.altera.com/content/dam/altera-www/global/en_US/pdfs/literature/ug/ug_vip.pdf
> +
> +Required properties:
> +----------------------------
> +- compatible: "altr,vip-frame-buffer-2.0"
> +- reg: Physical base address and length of the framebuffer controller's
> + registers.
> +- altr,max-width: The width of the framebuffer in pixels.
> +- altr,max-height: The height of the framebuffer in pixels.
> +- altr,bits-per-symbol: only "8" is currently supported
If only 8 is supported, then you don't need this property. You can
always add it later.
> +- altr,mem-port-width = the bus width of the avalon master port on the frame reader
> +
> +Example:
> +----------------------------
> + dp_0_frame_buf: vip@100000280 {
display-controller@...
> + compatible = "altr,vip-frame-buffer-2.0";
> + reg = <0x00000001 0x00000280 0x00000040>;
> + altr,max-width = <1280>;
> + altr,max-height = <720>;
> + altr,bits-per-symbol = <8>;
> + altr,mem-port-width = <128>;
> + };
> --
> 2.7.4
>