Re: [PATCH] pinctrl: cherryview: fix issues caused by dynamic gpio irqs mapping

[Grygorii Strashko]

On 10/07/2017 07:42 PM, Linus Walleij wrote:
> On Tue, Oct 3, 2017 at 7:00 PM, Grygorii Strashko
> <grygorii.strashko@xxxxxx> wrote:
> 
>> New GPIO IRQs are allocated and mapped dynamically by default when
>> GPIO IRQ infrastructure is used by cherryview-pinctrl driver.
>> This causes issues on some Intel platforms [1][2] with broken BIOS which
>> hardcodes Linux IRQ numbers in their ACPI tables.
>>
>> On such platforms cherryview-pinctrl driver should allocate and map all
>> GPIO IRQs at probe time.
>> Side effect - "Cannot allocate irq_descs @ IRQ%d, assuming pre-allocated\n"
>> can be seen at boot log.
>>
>> NOTE. It still may fail if boot sequence will changed and some interrupt
>> controller will be probed before cherryview-pinctrl which will shift Linux IRQ
>> numbering (expected with CONFIG_SPARCE_IRQ enabled).
>>
>> [1] https://bugzilla.kernel.org/show_bug.cgi?id=194945
>> [2] https://lkml.org/lkml/2017/9/28/153
>> Cc: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>
>> Cc: Chris Gorman <chrisjohgorman@xxxxxxxxx>
>> Cc: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
>> Cc: Heikki Krogerus <heikki.krogerus@xxxxxxxxxxxxxxx>
>> Signed-off-by: Grygorii Strashko <grygorii.strashko@xxxxxx>
>> Reported-by: Chris Gorman <chrisjohgorman@xxxxxxxxx>
>> Reported-by: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
> 
> OK patch applied for fixes.
> 
> But I'mm still very sceptical about this.
> 
> Look at the following (just from grep irq_base drivers/gpio/):
> 
> drivers/gpio/gpio-ml-ioh.c:
> 
> static int ioh_gpio_to_irq(struct gpio_chip *gpio, unsigned offset)
> {
>          struct ioh_gpio *chip = gpiochip_get_data(gpio);

It is ioh_gpio - not  gpio_chip ;)

>          return chip->irq_base + offset;
> }
> 
> (...)
>          ch = irq - chip->irq_base;
>          if (irq <= chip->irq_base + 7) {
>                  im_reg = &chip->reg->regs[chip->ch].im_0;
>                  im_pos = ch;
> (...)

not an issue gpio-ml-ioh.c:
ioh_gpio_probe()
 		irq_base = devm_irq_alloc_descs(&pdev->dev, -1, IOH_IRQ_BASE,
						num_ports[j], NUMA_NO_NODE);
...
		chip->irq_base = irq_base;
 


> 
> drivers/gpio/gpio-sta2x11.c:
> 
> static int gsta_gpio_to_irq(struct gpio_chip *gpio, unsigned offset)
> {
>          struct gsta_gpio *chip = gpiochip_get_data(gpio);
>          return chip->irq_base + offset;

same. It is gsta_gpio - not  gpio_chip ;)

> }
> 
> (etc)
> 
> The thing is that the lines you deleted from gpiolib were the only
> thing ever assigning chip->irq_base. This patch, if performed
> properly should have removed the .irq_base field from struct
> gpio_chip altogether without regressions.
> 
> As it is not, anything using .irq_base is regressing.
> 
> Either you need to convince me you can quickfix all of these
> users, or we need to simply revert this change.



-- 
regards,
-grygorii