Re: [PATCH v5 01/44] dt-bindings: clock: Add new bindings for TI Davinci PLL clocks

[Adam Ford]

On Thu, Jan 11, 2018 at 2:04 PM, David Lechner <david@xxxxxxxxxxxxxx> wrote:
> On 01/11/2018 12:50 PM, Adam Ford wrote:
>>
>> On Thu, Jan 11, 2018 at 12:29 PM, David Lechner <david@xxxxxxxxxxxxxx>
>> wrote:
>>>
>>> If removing the "clk_ignore_unused" option causes the board to not boot,
>>> then we still have problems that need to be fixed, so please also test
>>> without this option.
>>
>>
>> Without this option, it still does not boot.  Without device tree it
>> hangs after:
>>
>> [snip]
>>
>> NET: Registered protocol family 17
>> Loading compiled-in X.509 certificates
>> console [netcon0] enabled
>> netconsole: network logging started
>> davinci_emac davinci_emac.1: using random MAC addr: 5e:38:1a:1f:4f:77
>> mmc0: host does not support reading read-only switch, assuming
>> write-enable
>> hctosys: unable to open rtc device (rtc0)
>> mmc0: new high speed SDHC card at address b368
>>
>>
>> With device tree it hangs after:
>>
>> [snip]
>> mmc0: host does not support reading read-only switch, assuming
>> write-enable
>> mmc0: new high speed SDHC card at address b368
>> mmcblk0: mmc0:b368 00000 3.75 GiB
>>   mmcblk0: p1 p2
>> pca953x 0-0020: 0-0020 supply vcc not found, using dummy regulator
>> pca953x 0-0020: failed reading register
>> pca953x: probe of 0-0020 failed with error -121
>> console [netcon0] enabled
>> netconsole: network logging started
>> davinci_emac 1e20000.ethernet: incompatible machine/device type for
>> reading mac address
>> hctosys: unable to open rtc device (rtc0)
>>
>>
>
> Please try this change:
>
> diff --git a/drivers/clk/davinci/psc-da850.c
> b/drivers/clk/davinci/psc-da850.c
> index 3fd6b49..a526cc2 100644
> --- a/drivers/clk/davinci/psc-da850.c
> +++ b/drivers/clk/davinci/psc-da850.c
> @@ -17,7 +17,7 @@ static const struct davinci_psc_clk_info da850_psc0_info[]
> __initconst = {
>         LPSC(0, 0, tpcc0, pll0_sysclk2, LPSC_ALWAYS_ENABLED),
>         LPSC(1, 0, tptc0, pll0_sysclk2, LPSC_ALWAYS_ENABLED),
>         LPSC(2, 0, tptc1, pll0_sysclk2, LPSC_ALWAYS_ENABLED),
> -       LPSC(3, 0, aemif, pll0_sysclk3, 0),
> +       LPSC(3, 0, aemif, pll0_sysclk3, LPSC_ALWAYS_ENABLED),
>         LPSC(4, 0, spi0, pll0_sysclk2, 0),
>         LPSC(5, 0, mmcsd0, pll0_sysclk2, 0),
>         LPSC(6, 0, aintc, pll0_sysclk4, LPSC_ALWAYS_ENABLED),
>
>
>
> If that does not work, try adding LPSC_ALWAYS_ENABLED to all of the clocks
> in this file and then eliminate them one by one until you find which one is
> preventing boot.
>
Unfortunately, that didn't work.  I switch all the entries in both
tables that had a 0 to LPSC_ALWAYS_ENABLED, but no luck booting.

> If it still does not boot, there is a similar DIVCLK_ALWAYS_ENABLED flag in
> drivers/clk/davinci/pll-da850.c that you can repeat the exercise with. Add
> DIVCLK_ALWAYS_ENABLED to all of the clocks there and then eliminate it one
> by one until you find the clock that is causing the problem.

Still no good news.  I switched all the entries with a 0 to
DIVCLK_ALWAYS_ENABLED and it still didn't finish booting.

I wonder if Sekhar Nori might have some suggestions.  I didn't look at
the code or try to understand it.  I just changed the settings.
>

adam